LPC2114FBD64 - 60MHz ARM7 MCU 128KB Flash | NXP
料号: LPC2114FBD64 ✓ 量产中LPC2114FBD64 概述
An ARM7TDMI-S microcontroller is a 32-bit embedded processor core that can execute ARM or 16-bit Thumb instructions. The LPC2000 family combines that processor with memory, peripheral peripherals, interrupt handling, and communication interfaces in one package. The 128-bit wide memory interface and accelerator architecture support efficient 32-bit code execution, while Thumb mode can reduce code size for applications where memory density is important.
The LPC2114/2124 family provides 128 KB or 256 KB of embedded high-speed ISP/IAP flash, depending on the selected device. The LPC2114FBD64 is identified with 128 KB of flash in the manufacturer product listing and distributor documentation. The device also includes a 10-bit ADC, programmable I/O, PWM capability, and serial peripherals suited to industrial control, communications, consumer equipment, and general-purpose embedded products.
The 64-LQFP package provides 64 external leads and a compact surface-mount footprint. Its 10 mm by 10 mm body size supports conventional automated PCB assembly while leaving more routing space than many smaller leaded packages. The product family is based on an Arm7TDMI-S architecture with real-time emulation and embedded trace support, which assists development, debugging, and board bring-up.
Typical uses include industrial controllers, data acquisition equipment, communication modules, embedded gateways, motor and power-control systems, and consumer products. The integrated ADC and PWM outputs reduce the number of external devices required for sensing and actuator control, while flash memory allows firmware, boot software, and application code to reside on the MCU.
For PCB implementation, confirm the exact pin assignments, power rails, decoupling requirements, crystal or oscillator connections, programming interface, and exposed-pad or thermal requirements against the manufacturer datasheet. Use the package-specific land pattern and keep high-current supply paths compact. Firmware migration should also account for memory size, peripheral variants, oscillator configuration, and any differences in speed grade.
This product summary combines the manufacturer’s LPC2114FBD64 information with distributor technical listings, package details, and practical implementation guidance for engineers evaluating legacy embedded-control designs.
直接替换替代料: LPC2114FBD64 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
LPC2114FBD64/00
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LPC2114FBD64/01
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LPC2114FBD64/01,15
✅ 直接替换📋 参考替代料(不在目录中)
LPC2114FBD64/01,15
✅ 直接替换📋 参考替代料(不在目录中)
LPC2114FBD64/01
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LPC2114FBD64 最大额定值与电气特性
| Product Type | Single-chip 16/32-bit ARM microcontroller |
| CPU Core | Arm7TDMI-S |
| 最大时钟频率 | 60 MHz |
| Flash Memory | 128 KB |
| SRAM | 16 KB |
| ADC Resolution | 10 bit |
| Programmable I/O Pins | 46 |
| Instruction Set | 32-bit ARM and 16-bit Thumb |
| Memory Interface Width | 128 bit |
| Flash Type | Embedded ISP/IAP flash |
| 封装 | 64-LQFP, 10 mm x 10 mm |
| 引脚数量 | 64 pins |
| 安装类型 | Surface mount |
| 工作温度范围 | -40 °C to +85 °C |
| Core Voltage Range | 1.8 V to 1.95 V |
| Debug Support | Real-time emulation and embedded trace support |
| PWM Support | Yes |
| Terminal Pitch | 0.50 mm |
LPC2114FBD64 64-lqfp, 10 mm x 10 mm 引脚配置指南
LPC2114FBD64(64-lqfp, 10 mm x 10 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: LPC2114FBD64.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LPC2114FBD64 适用于 6 应用s: Industrial Control Systems, Data Acquisition Equipment, Communication Equipment, Motor and Power Control, Consumer Embedded Products, Embedded Development and Legacy Systems.
Industrial Control Systems
The LPC2114FBD64 fits compact industrial controllers that require deterministic control, sensor monitoring, and local communications. Its 60 MHz Arm7TDMI-S core provides processing headroom for protocol handling, while 128 KB of embedded ISP/IAP flash stores application and bootloader code. The 10-bit ADC supports process-input acquisition, 46 programmable I/O pins support digital interfaces, and PWM outputs can drive valves, indicators, or actuator command signals. The 64-LQFP package also preserves ample routing space on a control board.
推荐
Data Acquisition Equipment
The LPC2114FBD64 is appropriate for compact data-acquisition equipment that combines analog measurement with embedded control. Its 10-bit ADC can digitize sensor inputs, while the 60 MHz processor supports sampling control, filtering, local storage, and communication. With 128 KB flash and 16 KB SRAM, the device can execute focused acquisition firmware without requiring a separate memory component. The 64-LQFP footprint also leaves generous PCB space for analog conditioning, protection, and interface circuitry.
推荐
Communication Equipment
The LPC2114FBD64 can serve as the host controller in communication modules, gateways, and embedded protocol equipment. Its Arm7TDMI-S core supports 32-bit processing and 16-bit Thumb operation, allowing developers to balance throughput and code density. The 128 KB flash accommodates firmware, configuration, and network parameters, while serial and general-purpose I/O resources connect transceivers or companion interface devices. At 60 MHz, it is suitable for moderate protocol workloads that do not require a high-performance Cortex-M core.
推荐
Motor and Power Control
The LPC2114FBD64 is useful in motor-control and power-conversion subsystems where timing, ADC measurement, and PWM outputs must coexist in one controller. The 10-bit ADC can monitor feedback signals, and PWM channels support command generation for drivers or power stages. The 60 MHz Arm7TDMI-S processor can execute control loops, diagnostics, and communication routines. Designers should use the manufacturer timing and peripheral documentation to configure PWM synchronization and validate feedback latency.
推荐
Consumer Embedded Products
The LPC2114FBD64 fits cost-conscious embedded products requiring integrated flash and a compact surface-mount package. A typical product can use the 10-bit ADC for simple analog inputs, PWM for display or indicator control, and GPIO for buttons, sensors, and external logic. The 128 KB flash supports a self-contained firmware image, while 16 KB SRAM is adequate for many real-time control tasks. The 64-LQFP package is particularly useful where a smaller fine-pitch package would complicate assembly.
推荐
Embedded Development and Legacy Systems
The LPC2114FBD64 is a practical choice for maintaining or cloning legacy ARM7-based equipment. Existing LPC2100 firmware can be evaluated on a board using the same processor architecture, 128 KB flash organization, and 64-LQFP footprint. Its real-time emulation and embedded trace support assist board bring-up and diagnostics. For production migration, verify peripheral mapping, startup code, linker memory regions, oscillator settings, and any ordering-code differences before replacing an installed original device.
推荐
工程参考数据: LPC2114FBD64 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LPC2114FBD64/00 | LPC2114FBD64/01 | LPC2114FBD64/01,15 | LPC2114FBD64/01,15 | LPC2114FBD64/01 |
|---|---|---|---|---|---|---|
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| CPU Core | Arm7TDMI-S | Arm7TDMI-S | Arm7TDMI-S | Arm7TDMI-S | Arm7TDMI-S | Arm7TDMI-S |
| Maximum Clock Frequency | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| ADC Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit |
| Programmable I/O Pins | 46 pins | 46 pins | 46 pins | 46 pins | 46 pins | 46 pins |
关键差异点
- Integrated flash and SRAM in the same 64-LQFP controller (对比 LPC2114FBD64/01,15)
- 60 MHz Arm7TDMI-S processing with Thumb-mode support (对比 LPC2114FBD64/01)
- Integrated 10-bit ADC and PWM resources (对比 LPC2114FBD64/00)
设计说明
Use the manufacturer LQFP64 land pattern and pin-1 orientation when placing the LPC2114FBD64. Keep the 1.8 V to 1.95 V core supply and its decoupling network close to the supply pins, with short return paths to the ground plane. The 0.50 mm terminal pitch requires careful solder-paste and inspection control. Confirm whether the package includes an exposed thermal pad before defining copper and assembly clearance.
Plan the power tree so that the MCU core voltage remains within the manufacturer’s 1.8 V to 1.95 V range under startup, sleep, and maximum-clock operating states. Place bulk capacitance near the regulator output and local high-frequency decoupling beside the MCU supply pins. Validate startup current, peripheral rail sequencing, and clock-dependent current in the complete system rather than relying only on nominal core current.
Route oscillator and programming signals away from switching nodes and high-current return paths. The Arm7TDMI-S device depends on accurate clocking for stable timing, so keep crystal or oscillator traces short and ground-guarded where practical. Provide unobstructed access to the serial programming signals and avoid routing high-speed or noisy analog-adjacent traces beneath sensitive clock and reference circuitry.
Do not treat a similarly named LPC2114 suffix as automatically interchangeable without checking the ordering table. Speed-grade, temperature-range, qualification, and lead-finish codes can differ even when flash size and package remain unchanged. For firmware compatibility, also review startup code, linker memory regions, peripheral availability, interrupt vectors, and clock initialization when moving between LPC2114 ordering variants.
合规信息
No explicit compliance declarations were included in the manufacturer or distributor product information. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status using the exact ordering code and current manufacturer documentation.