LPC2124FBD64 - 60MHz ARM7TDMI-S MCU | NXP Semiconductors
料号: LPC2124FBD64 ✗ 停产LPC2124FBD64 概述
A microcontroller is a programmable semiconductor device that integrates a processor core, memory, and peripherals into one package. The LPC2124 belongs to the Arm7TDMI-S embedded-control hierarchy, combining deterministic real-time execution with in-system programming, in-application programming, analog conversion, timers, serial interfaces, and general-purpose I/O. This makes it suitable for industrial controllers, embedded data acquisition, communications equipment, and real-time monitoring systems.
The LPC2124FBD64 provides 256 KB of flash for firmware and 16 KB of SRAM for working data. Its 10-bit ADC supports analog measurement functions, while 46 GPIO pins provide flexible connections to sensors, actuators, displays, and communication transceivers. The 60 MHz Arm7TDMI-S core supports 32-bit instruction execution, and the accelerator architecture improves performance on suitable memory-intensive operations.
The device uses a 3.3 V CMOS supply according to the manufacturer product information. The LQFP-64 package has a 0.50 mm terminal pitch and is suitable for conventional surface-mount PCB assembly. Its documented operating-temperature range for the LPC2124FBD64/00,15 ordering variant is -40 °C to +85 °C. The manufacturer identifies the family as supporting real-time emulation and embedded trace functions.
Typical applications include industrial automation controllers, serial-protocol gateways, data-acquisition units, motor and process-control systems, and communications equipment. The combination of 256 KB flash, 16 KB SRAM, 46 I/O lines, and a 10-bit ADC supports compact embedded designs requiring both digital control and analog measurement.
For PCB implementation, assign the power, ground, reset, clock, and programming signals according to the manufacturer pin-description table in the LPC2124 datasheet. Place decoupling capacitors close to the supply pins and preserve the required signal-routing geometry around the 64-pin LQFP footprint. Firmware changes should follow the manufacturer’s ISP/IAP and flash-programming procedure rather than relying on undocumented bootloader behavior.
This page consolidates the manufacturer specifications, package information, ordering variants, and design guidance needed to evaluate the LPC2124FBD64, compare same-footprint family alternatives, and plan an embedded-controller board without duplicating the raw datasheet organization.
直接替换替代料: LPC2124FBD64 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LPC2124FBD64 (相同外形与封装尺寸) ——差异在于 Package, Programming Support, Terminal Pitch.
LPC2124FBD64/01,15
✅ 直接替换📋 参考替代料(不在目录中)
LPC2124FBD64-S
✅ 直接替换📋 参考替代料(不在目录中)
LPC2122FBD64
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LPC2129FBD64
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LPC2136FBD64
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LPC2124FBD64 最大额定值与电气特性
| CPU Core | Arm7TDMI-S 16/32-bit |
| Maximum CPU Frequency | 60 MHz |
| Flash Memory | 256 KB |
| SRAM | 16 KB |
| General-Purpose I/O Lines | 46 |
| ADC Resolution | 10 bit |
| 电源电压 | 3.3 V |
| 封装 | 64-pin LQFP, 10 mm x 10 mm |
| Terminal Pitch | 0.50 mm |
| Memory Interface Width | 128 bit |
| Programming Support | ISP/IAP flash |
| Debug Features | Real-time emulation and embedded trace |
| 工作温度 | -40 °C to +85 °C for LPC2124FBD64/00,15 |
| Technology | CMOS |
| Architecture | 32-bit code execution with accelerator architecture |
| 安装类型 | Surface mount |
| RoHS 状态 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
LPC2124FBD64 64-pin lqfp, 10 mm x 10 mm 引脚配置指南
LPC2124FBD64(64-pin lqfp, 10 mm x 10 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: LPC2124FBD64.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LPC2124FBD64 适用于 6 应用s: Industrial Automation Controller, Data Acquisition Unit, Serial Communications Gateway, Real-Time Monitoring System, Process and Motor Control, Embedded Communication Equipment.
Industrial Automation Controller
The LPC2124FBD64 fits compact industrial automation controllers because it combines a 60 MHz Arm7TDMI-S core, 256 KB of flash, 16 KB of SRAM, and 46 GPIO lines. The microcontroller can coordinate digital inputs, outputs, interlocks, and operator functions in one controller. Its 10-bit ADC supports process measurement when a sensor produces an analog voltage, while the 128-bit memory interface and accelerator architecture support responsive 32-bit execution. For an industrial board, use the exact manufacturer pin table, isolate external interface circuits, and confirm the required temperature suffix before deployment.
推荐
Data Acquisition Unit
The LPC2124FBD64 is suitable for a compact data-acquisition unit where sensor conditioning must be combined with local control. Its 10-bit ADC can digitize suitable analog inputs, while 46 GPIO lines permit multiplexed digital channels, status indicators, and control outputs. The 256 KB flash stores application firmware and calibration parameters, and the 16 KB SRAM supports acquisition buffers and communication state. Place analog and digital return paths carefully, reference the datasheet for ADC input limits, and include external conditioning when the sensor output exceeds the MCU input range.
推荐
Serial Communications Gateway
The LPC2124FBD64 can serve as a protocol gateway because the 60 MHz Arm7TDMI-S processor provides more than enough speed for multiple UART, SPI, or I2C-oriented tasks. Its 256 KB flash accommodates gateway firmware and protocol tables, while 16 KB SRAM supports message buffering. The 46 GPIO lines leave configuration and status-control resources available. Firmware should include protocol timeouts, CRC checks, and controlled buffering because the MCU does not provide an Ethernet interface directly. Validate each peripheral mapping and interrupt priority against the LPC2124 datasheet before releasing the PCB.
推荐
Real-Time Monitoring System
The LPC2124FBD64 fits real-time monitoring equipment that must sample inputs and report status without a separate processor. The Arm7TDMI-S core executes at up to 60 MHz, while the 10-bit ADC supports analog measurement and the 46 GPIO lines support digital sensors, alarms, and local controls. Embedded trace and real-time emulation features assist firmware development and diagnostics. A practical design should define sampling deadlines, isolate high-current outputs from sensitive analog paths, and use the manufacturer's recommended oscillator and decoupling arrangements to maintain predictable timing.
推荐
Process and Motor Control
The LPC2124FBD64 supports process-control or motor-control subsystems where deterministic execution, ample I/O, and mixed analog/digital functions are valuable. The 60 MHz core can execute control logic while 46 GPIO lines operate discrete inputs, outputs, and fault signals; the 10-bit ADC can monitor analog process or feedback signals. The 128-bit memory interface and accelerator architecture improve execution efficiency for 32-bit code. Choose external driver transistors or gate drivers for power stages, preserve separation between sensing and switching paths, and verify timing against the MCU’s operating limits.
推荐
Embedded Communication Equipment
The LPC2124FBD64 can be used in embedded communication equipment requiring a 32-bit processor, local protocol handling, and flexible serial connectivity. Its 256 KB flash supports embedded firmware, while 16 KB SRAM and the 60 MHz Arm7TDMI-S core provide room for message and control processing. The 46 GPIO lines can support modem control, link indicators, and configuration signals. Firmware development should take advantage of real-time emulation and embedded trace for task scheduling and interrupt analysis. Power sequencing, connector protection, and signal conditioning must be designed around the external communications hardware rather than assumed from the MCU specifications.
推荐
推荐产品汇总
工程参考数据: LPC2124FBD64 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LPC2124FBD64/01,15 | LPC2124FBD64-S | LPC2122FBD64 | LPC2129FBD64 | LPC2136FBD64 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-pin LQFP, 10 mm x 10 mm, 0.50 mm pitch | 64-pin LQFP | 64-pin LQFP | 64-pin LQFP family package | 64-pin LQFP family package | 64-pin LQFP family package |
| CPU Core | Arm7TDMI-S 16/32-bit | Arm7TDMI-S 16/32-bit | Arm7TDMI-S 16/32-bit | Arm7TDMI-S 16/32-bit | Arm7TDMI-S 16/32-bit | Arm7TDMI-S 16/32-bit |
| Programming Support | ISP/IAP flash | ISP/IAP flash | ISP/IAP flash | ISP/IAP flash family support | ISP/IAP flash family support | ISP/IAP flash family support |
关键差异点
- Higher flash capacity within the LPC2124 ordering family (对比 LPC2122FBD64)
- Defined 60 MHz operating point (对比 LPC2129FBD64)
- Established exact manufacturer ordering option (对比 LPC2136FBD64)
设计说明
Use the manufacturer LQFP-64 land pattern and verify every pin assignment against the LPC2124 pin-description table before routing. Keep the 0.50 mm pitch escape paths short and inspect the design for solder bridges on fine-pitch pads. Place input, output, and flash-bus routing away from switching nodes and high-current return paths. A pin-compatible package does not by itself establish that every peripheral signal has an identical alternate function.
The LPC2124FBD64 operates from a 3.3 V CMOS supply. Follow the manufacturer’s recommended power and decoupling network, placing each decoupling capacitor directly between the relevant power and ground pins with a short return path. Provide clean, stable source voltage for both core and I/O operation, and account for voltage drops across board traces. Do not derive supply limits from unrelated LPC21xx variants without checking the exact datasheet.
Separate analog and digital return currents carefully because the device includes a 10-bit ADC. Route analog inputs away from switching-node copper and digital clock lines, use a compact ground reference around the analog section, and avoid sharing narrow return paths between the ADC and high-current outputs. ADC accuracy depends on the selected external network and board noise environment, so validate the final layout with the system’s actual sensor and switching conditions.
Do not treat LPC2124FBD64, LPC2124FBD64/01,15, and LPC2124FBD64-S as interchangeable without checking the NXP ordering table, temperature grade, packing method, and marking scheme. Likewise, LPC2122, LPC2129, and LPC2136 share a broad family identity but may differ in memory, peripherals, and pin multiplexing. Preserve the original boot, clock, and ISP/IAP configuration when substituting a part into an existing design.
合规信息
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact LPC2124FBD64 ordering code in the manufacturer product information. AEC-Q100 is not applicable because this is not an automotive-qualified MCU variant.