LSF0102DDFR - 2-Ch 100Mbps Level Translator | TI
料号： LSF0102DDFR ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $0.85 | $0.85 |
| 10 | $0.76 | $7.60 |
| 100 | $0.54 | $54.00 |
| 500 | $0.42 | $210.00 |
| 1,000 | $0.33 | $330.00 |
LSF0102DDFR 概述
A level translator, or voltage level shifter, is a logic IC that enables digital signals to safely cross between circuits operating at different supply voltages, such as 1.8V, 3.3V, and 5V domains. Within the hierarchy of logic ICs, translators sit alongside buffers and bus switches in the signal-interface layer of a system, ensuring reliable communication in mixed-voltage designs.
Key features include fully automatic bidirectional translation with no direction pin, support for open-drain buses (I2C, SMBus) and push-pull interfaces (SPI, UART), a wide 0.95V to 5V translation range, and ultra-low quiescent current of 6 uA typical. The fast propagation delay preserves signal timing in high-speed links up to 100 Mbps.
Technically, the LSF0102 uses a pass-gate (transmission-gate) architecture. The reference pins VREF_A and VREF_B set the logic levels on each side, and external pull-up resistors define the high levels of each domain. The device senses data direction automatically, making it transparent to the host system and reducing pin count and firmware complexity compared to directional translators.
Typical applications include I2C and SMBus level shifting between 1.8V, 3.3V, and 5V domains, SPI and UART interfaces in mixed-voltage embedded systems, general-purpose GPIO translation, and battery-powered portable devices where the 6 uA quiescent current minimizes standby drain.
Design consideration: pull-up resistor values directly trade off maximum data rate against power consumption; use lower resistance (1-2 kilohm) for high-speed push-pull operation and higher resistance (4.7-10 kilohm) for low-power open-drain buses.
直接替换替代料： LSF0102DDFR ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： LSF0102DDFR （相同外形与封装尺寸） ——差异在于 Package.
快速对比工具——选择替代料号进行并排对比：
LSF0102-Q1
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →LSF0102DDFR 最大额定值与电气特性
| 通道数 | 2 |
| Translation Type | Auto-Bidirectional Multi-Voltage |
| Signal Type Support | Open-Drain and Push-Pull |
| 数据速率 | 100 Mbps |
| VCCA / VCCB Range | 1.8 V to 5.5 V |
| Reference Voltage Range (VREF) | 0.9 V to 5.5 V |
| Direction Control Pin | Not required (automatic) |
| 静态电流 | 6 uA (typical) |
| 工作温度 | -40C to +125C |
| 封装 | TSOT-23-8 (DDF), 8 pins |
| 安装类型 | Surface Mount |
| 输出类型 | Push-Pull, Open Drain |
| Input Logic Level | TTL |
| RoHS 状态 | Compliant |
| Feature | Partial power-down (Ioff) supported per LSF family |
LSF0102DDFR 引脚配置
| 引脚 1 | A1 — Channel 1, side A (low-voltage reference domain) |
| 引脚 2 | VREF_A — Reference voltage for side A, sets A-side logic low level |
| 引脚 3 | A2 — Channel 2, side A |
| 引脚 4 | GND — Ground |
| 引脚 5 | EN — Enable (high = translation active) |
| 引脚 6 | B2 — Channel 2, side B |
| 引脚 7 | VREF_B — Reference voltage for side B, sets B-side logic high level |
| 引脚 8 | B1 — Channel 1, side B |
典型应用
LSF0102DDFR 适用于 6 应用s: I2C / SMBus Level Shifting, Mixed-Voltage SPI and UART Interfaces, Battery-Powered Portable Devices, Automotive Mixed-Voltage Buses, Sensor Interface Translation in IoT Nodes, Industrial Control GPIO Translation.
I2C / SMBus Level Shifting
The LSF0102DDFR is purpose-built for open-drain I2C and SMBus translation between 1.8V, 3.3V, and 5V controllers and peripherals. Its auto-bidirectional transmission gate requires no direction pin, and the open-drain topology means only two channels are needed for SDA and SCL. With 4.7 kilohm pull-ups the bus supports 100 kHz Standard-mode, and 2 kilohm pull-ups enable 400 kHz Fast-mode operation while keeping the 6 uA quiescent current advantage.
推荐
Mixed-Voltage SPI and UART Interfaces
For SPI (MOSI, MISO, SCLK) and UART links crossing between a 1.8V microcontroller and 3.3V or 5V peripherals, the LSF0102DDFR provides automatic push-pull translation up to 100 Mbps. Two channels cover UART TX/RX; multiple devices can be cascaded for 4-wire SPI. Low 1.2 ns-class propagation delay preserves timing margins, and 1-2 kilohm pull-ups ensure fast rising edges at high clock rates.
推荐
Battery-Powered Portable Devices
The 6 uA typical quiescent current of the LSF0102DDFR minimizes standby drain in wearables, meters, and handheld instruments where the coin cell or Li-ion budget is tight. Its 0.9V reference floor allows translation from low-voltage sub-1.2V domain cores up to 5V accessory rails, and the small TSOT-23-8 package saves board area in space-constrained portable designs.
推荐
Automotive Mixed-Voltage Buses
Using the AEC-Q100 qualified LSF0102-Q1 variant (same die, same TSOT-23-8 footprint), designers can bridge 1.8V MCU domains to 3.3V or 5V automotive sensors and actuators across the -40C to +125C range. The open-drain support makes it ideal for translating LIN/K-line service interfaces and sensor I2C buses without direction-control firmware.
推荐
Sensor Interface Translation in IoT Nodes
IoT nodes frequently mix 1.8V low-power MCUs with 3.3V sensors. The LSF0102DDFR transparently shifts I2C sensor buses (temperature, humidity, accelerometers) in both directions with no software overhead. The wide 0.9V reference floor supports future migration to lower-voltage process nodes, and the small footprint suits dense multi-sensor PCBs.
推荐
Industrial Control GPIO Translation
In PLC and factory automation I/O modules, 5V field-side logic often meets 3.3V or 1.8V controller logic. The LSF0102DDFR handles push-pull GPIO, enable, and status lines across this boundary at speeds to 100 Mbps, with -40C to +125C operation for cabinet environments. Its pass-gate design adds negligible load to the bus, preserving signal integrity on long backplane traces.
推荐
推荐产品汇总
工程参考数据： LSF0102DDFR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LSF0102-Q1 | LSF0101 |
|---|---|---|---|
| Package | TSOT-23-8 (DDF) | TSOT-23-8 (DDF) - same, drop-in | Different package (1-channel family member) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Channels | 2 | 2 | 1 |
| Voltage Translation Range | 0.9 V to 5.5 V | 0.9 V to 5.5 V | 0.9 V to 5.5 V |
| Max Data Rate | 100 Mbps | 100 Mbps | 100 Mbps |
| Direction Control | Automatic (no DIR pin) | Automatic (no DIR pin) | Automatic (no DIR pin) |
| Quiescent Current | 6 uA (typ) | 6 uA (typ) | 6 uA (typ) |
| Automotive Grade | No | Yes (AEC-Q100) | No |
关键差异点
- Supports both open-drain and push-pull buses （对比 TXS0102-Q1)
- 0.9V reference floor （对比 SN74LVC2T45)
- Ultra-low 6 uA quiescent current （对比 LSF0101)
设计说明
Pull-up resistor selection dominates LSF0102 performance. Oversized resistors (10 kilohm+) create slow RC rising edges that cap usable data rate; undersized resistors increase static power on open-drain buses. Start with 4.7 kilohm for I2C at 100-400 kHz and 1-2 kilohm for push-pull links near 100 Mbps. Never omit pull-ups on the VREF_B side - the transmission-gate architecture relies on them to define high levels.
The VREF_B pin is also the B-side supply path; current through pull-up resistors flows via the device. Keep total pull-up current within datasheet limits, and hold VREF_B >= VREF_A per datasheet requirements (an LSF family constraint). With 6 uA typical quiescent current, the device itself is negligible for battery budget - the pull-up network is the real consumption term.
Place the TSOT-23-8 device close to the domain crossing point to minimize stub lengths, and add 100 nF decoupling on the VREF_B/VCC rail. For push-pull links above 50 Mbps, keep traces under 10 cm and reference to a solid ground plane; the pass-gate adds minimal series resistance but bus capacitance directly slows edges via the pull-up network.
合规信息
RoHS compliant per LCSC/JLCPCB product listings. AEC-Q100 qualified variant available as LSF0102-Q1 (separate MPN). REACH and halogen-free status not stated in provided data.
