MAX232AMLP - 2/2 RS-232 Transceiver, 5V | Analog Devices
料号: MAX232AMLP ✓ 量产中MAX232AMLP 概述
An RS-232 transceiver is a line-interface IC that bridges the logic-voltage domain used by digital controllers and the bipolar voltage domain used by RS-232 equipment. The MAX232A belongs to the MAX220 through MAX249 family of multichannel line drivers and receivers. Its integrated dual charge-pump voltage converters generate the positive and negative voltages required by RS-232 without requiring an external ±12 V supply.
Key features include two RS-232 drivers, two RS-232 receivers, operation from a single +5 V supply, and support for EIA/TIA-232E as well as V.28 and V.24 interfaces. The MAX232AMLP is appropriate when a system must transmit and receive asynchronous serial data between a 5 V logic circuit and an RS-232 port. Its through-hole ceramic package also supports applications that favor a rugged, leaded component over a surface-mount package.
The device combines charge-pump generation, driver outputs, and receiver inputs in one interface circuit. Charge-pump circuitry develops the RS-232 voltage rails from the +5 V supply, while the receivers provide the logic-side signaling required by the host controller. The MAX232A family is specifically intended for systems where ±12 V is unavailable, allowing a conventional regulated 5 V supply to serve both logic and interface requirements.
Typical uses include industrial serial-port equipment, test and measurement instruments, data acquisition systems, embedded serial adapters, and legacy computer peripherals. Two transmitter channels can support one hardware flow-control path while carrying data on the other, and two receiver channels can accept data and a status signal. Connection to a DB-9 or equivalent connector still requires the appropriate protection, filtering, and signal-routing components required by the target port.
When laying out the circuit, treat each driver output as a high-voltage RS-232 node and each receiver input as a sensitive line. Follow the manufacturer datasheet for charge-pump capacitor selection and placement, keep the external components close to their designated pins, and verify the connector-side protection network for the environmental conditions of the equipment. The ceramic LCC footprint and pin assignment must also be checked against the PCB library before assembly.
This page consolidates the exact MAX232AMLP package information, interface family characteristics, sourcing references, design guidance, and same-package comparison points. It also identifies where an engineer should consult the Analog Devices datasheet for the exact pin map, temperature range, capacitance values, and qualification attributes before releasing a production design.
直接替换替代料: MAX232AMLP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX232AMLP/883B
✅ 直接替换📋 参考替代料(不在目录中)
MAX232CMLP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX233AMLP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX233CMLP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX232AMLP
✅ 直接替换联系询价
查看数据手册 →MAX232AMLP 规格参数
| Product Type | RS-232 driver/receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| 电源电压 | +5 V |
| Interface Standard | EIA/TIA-232E |
| Supported Signaling Standards | V.28 and V.24 |
| 封装 | 20-LCC ceramic package |
| Package Dimensions | 8.9 mm x 8.9 mm |
| 安装类型 | Through-hole |
| Voltage Converter Configuration | Dual charge-pump DC-DC converters |
| External Positive Supply Requirement | Not required; single +5 V supply |
MAX232AMLP 8.9 mm x 8.9 mm 引脚配置指南
MAX232AMLP(8.9 mm x 8.9 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232AMLP.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232AMLP 适用于 6 应用s: Industrial Serial-Port Interface, Data Acquisition Equipment, Test and Measurement Instruments, Embedded Serial Adapters, Legacy Computer Peripherals, Data and Control Communication.
Industrial Serial-Port Interface
The MAX232AMLP fits legacy industrial controllers that expose an RS-232 port but operate from a regulated +5 V logic rail. Its two drivers and two receivers can carry one serial data path and a second pair of flow-control or status signals, while the integrated charge pumps eliminate a separate ±12 V supply. The 20-LCC ceramic package also suits through-hole industrial boards where leaded assembly, service access, and long product cycles are preferred. Confirm the exact pin assignment and external charge-pump capacitors in the MAX232A datasheet, and include suitable protection at the connector.
推荐
Data Acquisition Equipment
The MAX232AMLP is appropriate for laboratory and industrial data-acquisition equipment that must communicate with a host computer through an RS-232 connection. A +5 V system can use the transceiver's two transmit and two receive channels without adding a separate bipolar supply, reducing the interface power-tree complexity. The through-hole 20-LCC package is useful when the acquisition board uses conventional through-hole construction. Designers should verify the MAX232AMLP data rate and receiver thresholds for the selected cable length and place the required charge-pump capacitors close to the device.
推荐
Test and Measurement Instruments
The MAX232AMLP can provide the RS-232 port required by test equipment, service tools, and programmable instruments that use a single +5 V supply. Two receivers allow the controller to monitor a data line and an auxiliary status input, while two drivers can support command output and handshake signaling. The ceramic leaded package is especially attractive for instrument platforms assembled with through-hole workflows. For reliable operation, follow the Analog Devices reference circuit for charge-pump capacitors and verify that the selected connector includes the protection required by the operating environment.
推荐
Embedded Serial Adapters
The MAX232AMLP is suitable for embedded serial adapters that convert a 5 V UART signal into a full-duplex RS-232 connection. The two transmit channels can carry serial data and a hardware flow-control output, while the two receive channels can accept data and a hardware flow-control input. This avoids a separate level-shifter assembly in equipment designed around a legacy PC serial port. The through-hole ceramic package fits leaded adapter boards, but the PCB must use the exact 20-LCC footprint rather than a generic 20-pin DIP or SOIC footprint.
推荐
Legacy Computer Peripherals
MAX232AMLP addresses legacy computer peripherals and service equipment that communicate through an EIA/TIA-232E, V.28, or V.24 port. Because the interface operates from +5 V and contains the charge-pump converters internally, the design can retain an RS-232 connection without a separate ±12 V supply. The 20-LCC package supports retrofit boards that already accommodate a leaded ceramic footprint. Before using the part, confirm that the equipment's logic levels, handshake convention, and connector pin arrangement match the transceiver and its receiver and driver definitions.
推荐
Data and Control Communication
The MAX232AMLP can combine asynchronous data communication with hardware handshake signals in compact control equipment. Two drivers and two receivers allow a controller to exchange serial data while independently driving or monitoring request-to-send and ready-to-send lines. Its +5 V charge-pump architecture simplifies power distribution compared with an interface requiring external negative voltage, and its 20-LCC package preserves compatibility with leaded legacy hardware. Design the interface to use the correct RS-232 polarity and verify timing against the datasheet's specified driver and receiver propagation characteristics.
推荐
推荐产品汇总
工程参考数据: MAX232AMLP ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232AMLP/883B | MAX232CMLP | MAX233AMLP | MAX233CMLP | MAX232AMLP |
|---|---|---|---|---|---|---|
| Package | 20-LCC (8.9 mm x 8.9 mm) | 20-LCC (8.9 mm x 8.9 mm) | 20-LCC (8.9 mm x 8.9 mm) | 20-LCC (8.9 mm x 8.9 mm) | 20-LCC (8.9 mm x 8.9 mm) | 20-LCC (8.9 mm x 8.9 mm) |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver | 2/2 RS-232 transceiver |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Charge-Pump Configuration | Dual charge-pump converters | Dual charge-pump converters | Dual charge-pump converters | Dual charge-pump converters | Dual charge-pump converters | Dual charge-pump converters |
关键差异点
- Exact ceramic through-hole footprint retention (对比 MAX232AESE+)
- Two full-duplex interface channels (对比 MAX242EPN+)
- Single-supply charge-pump implementation (对比 MAX233EPP)
设计说明
Use the exact 20-LCC footprint from the MAX232A mechanical drawing rather than substituting a 20-pin DIP or SOIC library symbol. The LCC lead arrangement, body size, and pin-1 orientation determine solderability and clearance. Confirm each numbered lead against the datasheet pin-description table, especially if the board also uses another MAX232A variant whose multiplexing or external capacitor requirements differ.
Follow the manufacturer charge-pump capacitor values and connection diagram exactly; the +5 V supply does not make those capacitors optional. Place the charge-pump and interface capacitors adjacent to their assigned device pins, and provide a low-impedance supply connection to the relevant ground and supply pins. Avoid long current loops around the charge-pump network because they can increase supply disturbance and reduce margin on RS-232 outputs.
Do not treat a 20-pin RS-232 IC with a different package as a drop-in replacement. SOIC, plastic-DIP, and LCC versions can have different pin numbering, lead spacing, capacitance requirements, and thermal behavior. For a redesign, verify the MAX232AMLP logic levels, receiver thresholds, propagation timing, channel direction, and charge-pump topology against the candidate datasheet before updating the schematic and PCB.
合规信息
The interface standards EIA/TIA-232E, V.28, and V.24 are documented for the MAX232A family. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for the MAX232AMLP ordering code requires confirmation from the manufacturer or its compliance documentation.