MAX306EQI+ - 16:1 CMOS Multiplexer | Analog Devices
料号: MAX306EQI+ ✓ 量产中MAX306EQI+ 概述
An analog multiplexer is an analog switch network that routes one of several input signals to a common output while minimizing distortion, offset, and switching transients. In the signal-chain hierarchy, it belongs to the analog switch and multiplexer category within interface ICs. This precision CMOS implementation is designed for measurement, control, and instrumentation systems where selecting among closely spaced voltage or current signals requires consistent resistance and predictable switching behavior.
Key characteristics include on-resistance below 100 ohm, on-resistance matching between channels within 5 ohm, and variation across the specified analog signal range limited to 7 ohm maximum. Off leakage remains below 2.5 nA at +85 degrees Celsius, while low charge injection below 10 pC helps limit switching disturbances. The device also provides ESD protection greater than 2000 V and uses an improved 44 V silicon-gate CMOS process.
The MAX306's multiplexed architecture reduces the number of external signal connections required by a system. A common 16-to-1 arrangement can select one measurement channel for a shared amplifier or converter, while the family's dual 8-channel configuration can support two multiplexed groups. Matching within 5 ohm is particularly useful when channels are calibrated individually or when gain errors must remain predictable across a scan.
Typical uses include automated test equipment, data-acquisition systems, industrial process monitoring, laboratory instrumentation, and mixed-signal measurement modules. The sub-250 ns transition time supports higher-rate channel scanning, while low leakage and low charge injection are valuable when handling high-impedance sources, sensor outputs, or precision low-level signals.
Designers should verify the control-state truth table, pin assignments, supply requirements, and signal-range limits against the manufacturer datasheet before laying out the PCB. Keeping analog traces short, providing a stable reference and ground plane, and placing decoupling capacitors close to the device can help preserve the low-noise behavior expected from a precision analog multiplexer.
This page combines the manufacturer specifications with engineering-focused application guidance, package details, comparison parameters, and replacement analysis. It is intended to help designers select the correct multiplex configuration, recognize meaningful differences among related MAX306 order codes, and plan a PCB-compatible replacement before committing a precision analog signal chain to production.
直接替换替代料: MAX306EQI+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX306EQI
✅ 直接替换📋 参考替代料(不在目录中)
MAX306EQI+T
✅ 直接替换📋 参考替代料(不在目录中)
MAX306EQI+ 规格参数
| Multiplexer Configuration | 16-to-1 / dual 8-to-1 |
| Number of Circuits | 1 circuit |
| On-Resistance | Less than 100 ohm |
| On-Resistance Matching | Within 5 ohm between channels |
| On-Resistance Variation | 7 ohm maximum across the specified analog signal range |
| Off-Leakage Current | Less than 2.5 nA at +85 degrees Celsius |
| Charge Injection | Less than 10 pC |
| Transition Time | Less than 250 ns |
| ESD Protection | Greater than 2000 V |
| Process Technology | 44 V silicon-gate CMOS |
| 电源电压 | 5 V |
| 封装 | 28-pin PLCC, 11.51 x 11.51 mm |
| 安装类型 | Surface mount |
| Channel Count | 16 analog channels / dual 8-channel configuration |
MAX306EQI+ 28-pin plcc, 11.51 x 11.51 mm 引脚配置指南
MAX306EQI+(28-pin plcc, 11.51 x 11.51 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX306EQI+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX306EQI+ 适用于 6 应用s: Automated Test Equipment, Precision Data Acquisition, Industrial Process Monitoring, Laboratory Instrumentation, Mixed-Signal Control Systems, Battery-Powered Measurement Module.
Automated Test Equipment
The MAX306EQI+ fits automated test systems that must route many test points to a shared measurement chain. Its 16-to-1 configuration reduces the number of analog connections required between the device under test and downstream instrumentation. Less than 100 ohm on-resistance and channel matching within 5 ohm help maintain predictable signal amplitude across the selected channel, while transition time below 250 ns supports rapid point selection. Place the multiplexer close to the instrument amplifier when source impedances are high to minimize added sensitivity to capacitance and noise pickup.
推荐
Precision Data Acquisition
The MAX306EQI+ is appropriate for multichannel data-acquisition modules in which several sensor or divider outputs share an amplifier and analog-to-converter input. Its 16-to-1 routing reduces wiring complexity, while off leakage below 2.5 nA at +85 degrees Celsius is useful with high-impedance sources. Charge injection below 10 pC limits the voltage disturbance created when a channel is selected. The 28-pin PLCC footprint is suitable for surface-mount assembly, and the less-than-250 ns transition time enables faster scans when downstream filtering does not dominate settling time.
推荐
Industrial Process Monitoring
The MAX306EQI+ can select pressure, temperature, or level signals from multiple industrial sensors and route them into a shared conditioning circuit. Its on-resistance remains below 100 ohm, and channel-to-channel matching within 5 ohm supports repeatable measurements when each input path is calibrated. Low off leakage reduces loading errors in high-impedance sensor circuits, while ESD protection greater than 2000 V adds handling robustness. The design should still use protected routing, appropriate grounding, and input-range protection because those protections are separate from the multiplexer's internal ESD rating.
推荐
Laboratory Instrumentation
The MAX306EQI+ fits laboratory instruments that connect multiple transducers, reference nodes, or programmable inputs to a common precision front end. The 16-to-1 topology keeps the analog routing compact while matching within 5 ohm and limiting on-resistance variation to 7 ohm maximum across the specified signal range. Those characteristics help preserve repeatable gain and offset calibration. Transition time below 250 ns permits rapid channel selection, while low charge injection below 10 pC reduces the disturbance seen by sensitive downstream circuitry.
推荐
Mixed-Signal Control Systems
The MAX306EQI+ is useful in mixed-signal control boards that must select feedback, setpoint, or diagnostic signals before conversion by a common analog channel. Its 16-to-1 architecture simplifies the routing matrix and reduces the number of external analog switches. The less-than-100-ohm on-resistance provides low series impedance for typical low-impedance sensor interfaces, and the sub-250 ns transition time supports responsive channel updates. For high-precision control, include settling time, charge injection, and the finite on-resistance in the loop-error budget rather than treating channel selection as instantaneous.
推荐
Battery-Powered Measurement Module
The MAX306EQI+ can reduce analog routing hardware in compact battery-powered measurement modules by selecting up to 16 external signals through one common path. The multiplexer's 28-pin PLCC package supports compact surface-mount layouts, and its low leakage can limit the load imposed on high-impedance sensors between selections. Designers must still budget for quiescent current and supply requirements using the manufacturer datasheet. Low on-resistance helps prevent the selected sensor from seeing excessive divider loading, although cable capacitance and leakage should also be evaluated.
推荐
推荐产品汇总
工程参考数据: MAX306EQI+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX306EQI | MAX306EQI+T |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-PLCC (11.51 x 11.51 mm) | 28-PLCC (11.51 x 11.51 mm) | 28-PLCC (11.51 x 11.51 mm) |
| Multiplexer Configuration | 16:1 | 16:1 | 16:1 |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit |
| On-Resistance | Less than 100 ohm | Less than 100 ohm | Less than 100 ohm |
| On-Resistance Matching | Within 5 ohm between channels | Within 5 ohm between channels | Within 5 ohm between channels |
| Charge Injection | Less than 10 pC | Less than 10 pC | Less than 10 pC |
| Transition Time | Less than 250 ns | Less than 250 ns | Less than 250 ns |
| Off-Leakage Current | Less than 2.5 nA at +85 degrees Celsius | Less than 2.5 nA at +85 degrees Celsius | Less than 2.5 nA at +85 degrees Celsius |
关键差异点
- Combines precision channel matching with rapid switching (对比 MAX306EQI)
- Maintains the same electrical architecture across production suffixes (对比 MAX306EQI+T)
- Low channel disturbance for precision acquisition (对比 MAX306EQI)
设计说明
Use the Analog Devices package drawing to create the 28-pin PLCC footprint and confirm the orientation of pin 1 before routing. Place the device near the source of the multiplexed signals when high-impedance nodes are involved, because long copper tracks can add parasitic capacitance and increase settling time. Keep the common output path short and route it away from switching-clock and digital-control traces.
Include on-resistance, source impedance, amplifier input capacitance, and the downstream filter in the settling-time calculation. The specified transition time below 250 ns does not by itself define the time required for a complete measurement acquisition. For high-impedance sources, verify leakage and capacitance against the MAX306/MAX307 datasheet because the switched capacitance can determine how long the measurement chain requires to settle.
Provide a continuous ground reference beneath and around the analog routing area, and place supply-decoupling components close to the device pins using the manufacturer layout guidance. Keep the analog common node away from high-current return paths and switching power-converter nodes. Although the device provides ESD protection greater than 2000 V, external protection may still be required for accessible industrial connectors and long external wiring.
Do not assume that every MAX306 order suffix is interchangeable at procurement. MAX306EQI+ and MAX306EQI+T use the same core 16-to-1 electrical architecture and 28-pin PLCC package, but the suffix can affect packing, shipment form, or qualification. Confirm the exact part marking, temperature grade, reel configuration, assembly method, and manufacturer ordering information before approving a substitution.
合规信息
The MAX306 product page identifies the family as production, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were established from the cited content.