MAX3232EEAE+ - 15kV ESD 16-SSOP RS-232 IC | Analog Devices
料号: MAX3232EEAE+ ✓ 量产中MAX3232EEAE+ 概述
A true RS-232 transceiver is an interface IC that integrates line drivers, line receivers, and charge-pump circuitry. Its role in the hierarchy is UART controller to RS-232 transceiver to serial connector. This is different from a UART transceiver that handles only logic-level signaling or an RS-485 interface, which uses differential signaling. The MAX3232EEAE+ is intended for industrial-control, instrumentation, and embedded data links requiring a compact multi-line interface.
The main features include two transmit drivers, two receive receivers, dual charge-pump voltage generation, ±15 kV ESD protection, and a low-power design described as operating down to 10 nA. Its 3.0 V to 5.5 V supply range supports both 3.3 V and 5 V systems. Data rates of up to 1 Mbps make the device suitable for moderate-speed serial links, including legacy RS-232 ports, point-to-point equipment interfaces, and industrial service connections.
The dual charge-pump architecture generates the positive and negative voltage levels required by true RS-232 drivers from a single low-voltage supply. Four external charge-pump capacitors support the internal voltage conversion. The integrated receivers invert the incoming RS-232 levels and provide compatible logic-level outputs to the host UART. The Analog Devices MAX3232E data sheet, Rev. 13, identifies the device as a true RS-232 transceiver with pin-to-pin protection on the serial-port connections.
Typical applications include industrial serial adapters, programmable-logic-controller service ports, instrumentation interfaces, embedded controller communication, and point-to-point control links. The compact 16-pin SSOP package helps reduce board area when two drivers and two receivers are required. The 1 Mbps maximum data rate provides ample margin for many legacy serial protocols, although cable length, baud rate, grounding, and signal integrity must be evaluated together.
For layout, follow the charge-pump capacitor connections and polarity shown in the manufacturer data sheet exactly. Place the four external capacitors close to their associated pins, route serial outputs away from sensitive analog inputs, and provide a low-impedance return path between connected equipment. Use an appropriate connector and board-level protection strategy when exposed cables carry greater electrostatic-discharge risk.
This page combines the MAX3232E family specifications, ordering information, pin-compatible alternatives, application guidance, and practical interface-design notes. It is intended to help engineers confirm package fit, voltage compatibility, protection requirements, and replacement strategy before integrating the MAX3232EEAE+ into an RS-232 design.
直接替换替代料: MAX3232EEAE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX3232EEAE+ (相同外形与封装尺寸) ——差异在于 ESD Protection, Supply Voltage Range, Interface Standard, Package, Product Type.
MAX3232EEAE
✅ 直接替换📋 参考替代料(不在目录中)
MAX3232EEAE+ 规格参数
| Product Type | True RS-232 transceiver |
| Line Drivers | 2 |
| Line Receivers | 2 |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps |
| ESD Protection | ±15 kV |
| Low-Power Operation | Down to 10 nA |
| Charge Pumps | 2 |
| External Charge-Pump Capacitors | 4 capacitors |
| Package Type | SSOP-16 |
| 引脚数量 | 16 pins |
| 安装类型 | Surface mount |
| Interface Standard | TIA/EIA-232-F |
MAX3232EEAE+ ssop-16 引脚配置指南
MAX3232EEAE+(ssop-16 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3232EEAE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3232EEAE+ 适用于 6 应用s: Industrial Serial Port Interface, Embedded Controller Serial Link, Test and Measurement Equipment, Point-to-Point Control Systems, Instrumentation and Data Acquisition, Legacy Computer and Peripheral Connectivity.
Industrial Serial Port Interface
The MAX3232EEAE+ fits industrial equipment that must translate between a 3.3 V or 5 V UART and a true RS-232 connector. Its two drivers and two receivers support a compact point-to-point interface, while the 3.0 V to 5.5 V supply range accommodates both common logic rails. The Analog Devices MAX3232E data sheet, Rev. 13, specifies operation up to 1 Mbps and ±15 kV ESD protection, useful characteristics for service ports connected through exposed cables. Place the four required charge-pump capacitors close to their pins and route driver outputs away from sensitive analog nodes.
推荐
Embedded Controller Serial Link
The MAX3232EEAE+ provides a straightforward interface between an embedded controller's UART and an external RS-232 device. Two driver and two receiver channels allow bidirectional communication when both ends of the link are RS-232, and the 3.0 V to 5.5 V range supports common embedded supply rails. The 1 Mbps capability is substantially above many legacy peripheral baud rates. Use the manufacturer application circuit as the PCB-layout reference, maintain a common ground reference, and verify the selected connector and cable shielding against the installation environment.
推荐
Test and Measurement Equipment
The MAX3232EEAE+ is appropriate for test and measurement instruments that need a legacy RS-232 control or data port alongside modern UART logic. The 2/2 channel configuration provides enough drivers and receivers for common point-to-point instrument arrangements without occupying a larger multi-channel package. Its ±15 kV ESD protection helps improve interface robustness, while operation from 3.0 V to 5.5 V simplifies supply planning. Confirm equipment-grounding practices, use shielded cable where appropriate, and keep external charge-pump capacitors close to the device to follow the reference circuit.
推荐
Point-to-Point Control Systems
The MAX3232EEAE+ can serve as the electrical interface in point-to-point control and monitoring systems where one controller communicates with a remote subsystem over RS-232. Its true RS-232 drivers and receivers are intended for unbalanced serial connections, and the dual charge pump generates the required signal levels from one low-voltage supply. The 1 Mbps maximum data rate allows operation beyond many legacy serial-port speeds. Design the cable route and grounding carefully, because connector protection alone does not replace proper signal-return and enclosure practices.
推荐
Instrumentation and Data Acquisition
The MAX3232EEAE+ is suitable for instrumentation modules that exchange commands or measurement data with a host computer through RS-232. The two receivers and two drivers offer a balanced channel count for typical request-and-response arrangements, while low-power operation down to 10 nA can benefit compact systems. The device operates from 3.0 V to 5.5 V and supports rates up to 1 Mbps. Place external capacitors close to the charge-pump pins, keep receive traces away from switching nodes, and use the Analog Devices application diagram as the layout baseline.
推荐
Legacy Computer and Peripheral Connectivity
The MAX3232EEAE+ provides a practical bridge between a modern embedded UART and a legacy RS-232 peripheral. Its 3.0 V minimum supply supports 3.3 V systems, while the 5.5 V maximum allows use in established 5 V equipment. Two drivers and two receivers are sufficient for several desktop-style peripheral connections, and the 1 Mbps rating provides headroom for common serial baud rates. Verify the exact logic polarity, pin assignment, and connector wiring in the manufacturer data sheet before production, and confirm that any baud-rate inversion or hardware handshaking is handled correctly.
推荐
推荐产品汇总
工程参考数据: MAX3232EEAE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3232EEAE |
|---|---|---|
| Package | SSOP-16 | SSOP-16 |
| Brand | Analog Devices | Analog Devices |
| Device Type | True RS-232 transceiver | True RS-232 transceiver |
| Number of Drivers | 2 | 2 |
| Number of Receivers | 2 | 2 |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Maximum Data Rate | 1 Mbps | 1 Mbps |
| ESD Protection | ±15 kV | ±15 kV |
| External Charge-Pump Capacitors | 4 capacitors | 4 capacitors |
| Interface Compliance | TIA/EIA-232-F | TIA/EIA-232-F |
关键差异点
- Compact two-channel true RS-232 interface (对比 MAX3232EEAE)
- Integrated electrostatic-discharge protection (对比 MAX3232EEAE)
- True RS-232 operation from a single low-voltage supply (对比 MAX3232EEAE)
设计说明
Use the Analog Devices MAX3232E data sheet, Rev. 13, application diagram as the authority for the four external charge-pump capacitors. Place each capacitor close to the associated IC pin and minimize loop area around the charge-pump connections. Correct capacitor value, polarity where applicable, and pin assignment are essential because incorrect connections can prevent the drivers from producing valid RS-232 levels.
Keep the two RS-232 driver outputs physically separated from sensitive receiver inputs and nearby low-level analog circuitry. Route serial traces over a continuous ground reference, avoid long stubs to connectors, and provide a direct return path between communicating systems. Although the device provides ±15 kV ESD protection, board layout and enclosure grounding remain part of the system-level ESD strategy.
Do not treat SSOP-16, TSSOP-16, and SOIC-16 as interchangeable footprints solely because each has 16 pins. The MAX3232EUE+ is identified as TSSOP-16 and the MAX3232ECDR as SOIC-16, while the MAX3232EEAE+ uses SSOP-16. Check body width, lead span, land pattern, and counterclockwise pin numbering against the PCB footprint before approving a substitute.
Confirm the exact ordering suffix, temperature grade, and delivery format when releasing a BOM. The base part, lead-free designation, and tape-and-reel suffix are separate ordering details, and mixing them can create assembly or traceability issues. Have procurement confirm the marking and package against the approved manufacturer ordering table before accepting material.
合规信息
The manufacturer product page identifies TIA/EIA-232-F interface compliance. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the available product information.