MAX3232EEUP+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices
料号: MAX3232EEUP+TG1Z ✓ 量产中MAX3232EEUP+TG1Z 概述
An RS-232 transceiver is an interface IC that converts between complementary logic-level signals and the voltage-defined signaling used by RS-232 equipment. The MAX3232EEUP+TG1Z belongs to the RS-232 transceiver class within interface ICs and semiconductor signal-conditioning products. Its integrated level conversion allows a low-voltage digital system to communicate with legacy serial peripherals, industrial controllers, and computer equipment without external line-driver circuitry.
The device provides two transmit channels and two receive channels, supporting full-duplex point-to-point links when both directions are required. Operation across a 3.0V to 5.5V supply range allows it to interface with 3.3V and 5V digital logic systems. The 1Mbps maximum data rate supports modern high-speed serial links, while 15kV ESD protection strengthens the interface against electrostatic discharge encountered in industrial and commercial environments.
The MAX3232E family uses an on-chip charge-pump circuit to generate the positive and negative voltage levels required by RS-232 transmitters. This architecture permits true RS-232 operation from a single low-voltage supply. The manufacturer identifies the MAX3232E as pin, package, and functionally compatible with the industry-standard MAX232, while also providing low-power characteristics suited to portable and power-conscious equipment.
Typical applications include industrial serial adapters, data-acquisition equipment, test and measurement instruments, point-of-sale terminals, and control systems that exchange data with RS-232 devices. The 20-pin TSSOP package supports compact surface-mount construction, although correct charge-pump capacitor placement and controlled RS-232 signal routing remain essential for reliable operation.
For PCB design, place the external charge-pump capacitors close to their associated pins and keep RS-232 driver traces away from sensitive logic or analog nets. Confirm logic thresholds and signal direction before connecting external equipment because the transceiver's TTL-side inputs and outputs do not provide galvanic isolation. Confirm electrostatic requirements against the application's enclosure, grounding, and cable environment.
This page combines manufacturer compatibility information, structured technical specifications, practical application guidance, and same-package replacement analysis to support faster component selection and PCB-level replacement decisions.
直接替换替代料: MAX3232EEUP+TG1Z ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX3232EEUP+TG1Z (相同外形与封装尺寸) ——差异在于 ESD Protection.
MAX3232EEUP+
✅ 直接替换联系询价
查看数据手册 →MAX3232EEUP
✅ 直接替换📋 参考替代料(不在目录中)
MAX3222EEUP+TG1Z
✅ 直接替换📋 参考替代料(不在目录中)
MAX3232EUP+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX3232CUP+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX3232EEUP+TG1Z 规格参数
| Product Type | RS-232 transceiver |
| Number of Transmitters | 2 |
| Number of Receivers | 2 |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 1Mbps |
| ESD Protection | 15kV |
| Low-Power Supply Current | 10nA |
| Interface Standard | True RS-232 |
| 封装 | 20-pin TSSOP |
| 安装类型 | Surface mount |
MAX3232EEUP+TG1Z 20-pin tssop 引脚配置指南
MAX3232EEUP+TG1Z(20-pin tssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3232EEUP+TG1Z.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3232EEUP+TG1Z 适用于 6 应用s: Industrial Serial Data Acquisition, Test and Measurement Instruments, Point-of-Sale Terminal Interfaces, Embedded Control and Monitoring, Data Communications Equipment, Portable Diagnostic Equipment.
Industrial Serial Data Acquisition
The MAX3232EEUP+TG1Z fits legacy RS-232 data-acquisition equipment because it provides two transmit channels, two receive channels, and operation up to 1Mbps from a 3.0V to 5.5V supply. Place the device between the controller's logic-level UART and the isolated or grounded RS-232 connector circuitry. Its 15kV ESD protection improves interface robustness in industrial environments, while the integrated charge pump generates compliant positive and negative line voltages. The 20-pin TSSOP layout keeps the converter compact, although external charge-pump capacitors must be placed close to their pins and the RS-232 route should be kept away from sensitive measurement circuitry.
推荐
Test and Measurement Instruments
The MAX3232EEUP+TG1Z is suitable for RS-232 control and response ports on test and measurement instruments because it combines a 1Mbps data rate with a 3.0V to 5.5V supply range. A modern instrument controller can communicate through logic-level UART pins while the transceiver supplies the required RS-232 voltage levels. Two transmitters and two receivers support bidirectional control and status channels without adding another package. Use short, controlled traces between the transceiver and connector, and apply the datasheet's charge-pump capacitor placement to minimize coupling into the instrument's analog or precision timing sections.
推荐
Point-of-Sale Terminal Interfaces
The MAX3232EEUP+TG1Z can connect a compact point-of-sale controller to older RS-232 peripherals such as scanners, printers, or customer displays. The 3.0V to 5.5V operating range allows use with 3.3V and 5V control electronics, while the 1Mbps capability provides ample bandwidth for short command and transaction exchanges. Two receivers can monitor peripheral status and two transmitters can support control and data paths. Keep the cable-side nets physically separated from high-speed logic, and verify ground relationships because RS-232 does not provide galvanic isolation between connected systems.
推荐
Embedded Control and Monitoring
The MAX3232EEUP+TG1Z is appropriate for embedded controllers that must communicate with RS-232 sensors, service tools, or remote monitoring units. A 3.3V controller can operate the transceiver within its 3.0V to 5.5V range, and the 1Mbps rate supports responsive command traffic. The integrated ESD protection is valuable where cables enter compact or industrial enclosures, although it does not replace surge protection for long cables. Maintain a controlled ground reference, avoid placing the RS-232 traces beneath sensitive digital routes, and use the manufacturer's recommended capacitor values for stable charge-pump operation.
推荐
Data Communications Equipment
The MAX3232EEUP+TG1Z fits legacy data-communications equipment requiring bidirectional RS-232 connectivity without a separate positive and negative supply. Its two transmitters and two receivers support full-duplex links when both ends of a port are active, while the single 3.0V to 5.5V supply simplifies system power design. The 1Mbps maximum rate is suitable for command-oriented links and legacy peripheral traffic. In multiport systems, allocate the two channels carefully and preserve the distinction between logic-side and cable-side pins to prevent incorrect transmitter or receiver connections.
推荐
Portable Diagnostic Equipment
The MAX3232EEUP+TG1Z supports portable diagnostic and configuration equipment that uses RS-232 for service access or external sensor connections. The low-power current down to 10nA is advantageous when the equipment spends substantial time in a low-energy state, while the 3.0V to 5.5V supply range accommodates portable logic levels. Its 20-pin TSSOP package supports compact surface-mount construction. Confirm the active-state supply consumption for the final battery budget, and follow the recommended shutdown-state behavior if the serial interface must remain available for remote monitoring.
推荐
推荐产品汇总
工程参考数据: MAX3232EEUP+TG1Z ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3232EEUP+ | MAX3232EEUP | MAX3222EEUP+TG1Z | MAX3232EUP+ | MAX3232CUP+ |
|---|---|---|---|---|---|---|
| Package | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transmitter Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Receiver Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V | 3.0V to 5.5V |
| Industry Compatibility | Pin, package, and functionally compatible with MAX232 | MAX3232E compatible | MAX3232E compatible | MAX3222E compatible | MAX3232E compatible | MAX3232C family |
关键差异点
- Lower specified low-power current (对比 MAX3222EEUP+TG1Z)
- Direct MAX232 interface compatibility (对比 MAX3232CUP+)
- One-Mbps operation with modern supply range (对比 MAX3232EUP+)
设计说明
Place the external charge-pump capacitors directly beside the designated MAX3232E pins and use the capacitance and tolerance specified in the manufacturer datasheet. Keep the capacitor return paths short and avoid routing the charge-pump nets beneath the analog section. Correct placement reduces switching transients and helps the transmitters maintain stable RS-232 voltage levels under data traffic.
Separate logic-side nets from RS-232 cable-side nets in the PCB layout and maintain clear spacing around connector entry points. Route the RS-232 lines away from clocks, ADC inputs, and sensitive sensor traces. Where a cable can introduce surge energy beyond the device's 15kV ESD capability, add an appropriately rated external protection network and verify it does not distort receiver thresholds.
Do not treat TTL logic pins and RS-232 line pins as interchangeable. Confirm each transmitter output, receiver input, ground, supply, and charge-pump connection against the manufacturer pin-description table. Also check whether the application expects receiver monitoring during shutdown; MAX3222E-family behavior differs from MAX3232E-family behavior and can affect a drop-in decision.
合规信息
The + ordering designation may be associated with lead-free or RoHS status, but the manufacturer document linked by the product listing does not explicitly state the applicable status. Confirm the ordering guide and material declaration for the exact suffix before release.