MAX369EWN+ - Dual 4:1 Fault-Protected Analog MUX | Maxim
料号: MAX369EWN+ ✓ 量产中MAX369EWN+ 概述
An analog multiplexer is an interface IC that connects multiple signal sources to a shared amplifier, converter, or measurement channel. The MAX369 family belongs to the analog-switch and multiplexer hierarchy, where switch resistance, channel isolation, logic compatibility, fault tolerance, and switching behavior determine signal integrity. A dual 4:1 configuration is useful when a system must alternate among several sensors, instrument channels, or control signals without duplicating the downstream conversion circuitry.
The MAX369EWN+ provides a specified 1.8 kOhm switch resistance and guaranteed break-before-make operation. Break-before-make prevents two input paths from being connected together during channel transitions, an important behavior when routing externally sourced signals. Its fault-protected architecture and latch function help control switch states when abnormal conditions occur. Typical power dissipation is stated as less than 7 mW, supporting low-power portable equipment.
MAX369EWN+ is identified as an industrial-temperature differential multiplexer in an 18-pin SOIC package. The SOIC package supports conventional surface-mount assembly while exposing the selector and control signals directly to the device pins. Because the MAX369 family is designed for portable equipment, system designers should pay particular attention to signal levels, control sequencing, and the interaction between fault protection and downstream amplifier input networks.
Typical uses include battery-powered instrumentation, portable measurement systems, analog test equipment, sensor-selection circuits, and industrial control modules. The dual architecture can support two independent 4:1 switching groups, while TTL- and CMOS-compatible selection inputs simplify connection to microcontrollers, logic controllers, and counter-based channel-selection circuits.
PCB layout should keep selected and unselected signal paths short and should route sensitive analog inputs away from digital selector traces. Verify the complete pin description table in the manufacturer datasheet before assigning PCB tracks, especially for differential inputs, fault-protection pins, and common terminals. Decoupling should follow the manufacturer’s recommended capacitor values and placement instructions.
This page combines the manufacturer’s device positioning with distributor package data, a verified same-family cross-reference, and application-oriented design guidance. It also distinguishes the MAX369EWN+ from reel-packaging notation and identifies the confirmed drop-in alternative without presenting unverified cross-brand parts as direct replacements.
直接替换替代料: MAX369EWN+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX369CWN
✅ 直接替换📋 参考替代料(不在目录中)
MAX369EWN+ 规格参数
| Product Type | Dual 4:1 fault-protected analog multiplexer with latch |
| Number of Multiplexer Circuits | 2 circuits |
| Configuration | Dual 4:1 |
| On-Resistance | 1.8 kOhm |
| Control Logic Compatibility | TTL and CMOS compatible |
| Switching Behavior | Guaranteed break-before-make |
| Typical Power Dissipation | <7 mW |
| 封装 | 18-SOIC |
| 安装类型 | Surface mount |
| Temperature Grade | Industrial |
| Number of Terminals | 16 terminals |
| Package Shape | Rectangular |
| Analog Signal Type | Differential multiplexer |
| Fault Protection | Supported with latch |
MAX369EWN+ rectangular 引脚配置指南
MAX369EWN+(rectangular 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX369EWN+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX369EWN+ 适用于 6 应用s: Portable Sensor Multiplexing, Industrial Test and Measurement, Battery-Powered Instrument, Analog Control Signal Routing, Data Acquisition Front End, Remote Sensor Interface.
Portable Sensor Multiplexing
The MAX369EWN+ fits portable sensor-acquisition systems that must route several analog inputs into a shared amplifier or converter. Its two independent 4:1 sections provide eight switched input positions, while the 1.8 kOhm on-resistance defines the series impedance that must be included in source-load calculations. TTL- and CMOS-compatible controls simplify interfacing with a microcontroller or counter, and typical power dissipation below 7 mW supports low-power operation. Guaranteed break-before-make operation is especially useful when adjacent sensors may drive different signal levels, because it prevents intentional overlap during channel transitions.
Industrial Test and Measurement
In a compact test instrument, the MAX369EWN+ can select among multiple analog test points and present them to a shared measurement chain. The dual 4:1 organization allows two banks of four sources to be routed independently, reducing duplication in downstream amplification or conversion circuitry. Its 1.8 kOhm on-resistance is a primary design constraint for high-impedance sensors and should be checked against the complete source impedance. The guaranteed break-before-make characteristic helps prevent two test channels from being connected during a transition, improving control of excitation and measurement sequencing.
Battery-Powered Instrument
The MAX369EWN+ is suited to battery-operated instruments where channel selection must consume little power and support both CMOS and TTL control environments. Its typical power dissipation is specified as less than 7 mW, making the switching stage suitable for compact portable equipment. The dual 4:1 architecture consolidates multiple analog inputs onto fewer downstream signal paths, while fault protection and latch capability provide defined control behavior during abnormal conditions. Designers should still budget input filtering, grounding, and control-driver current in the complete battery budget.
Analog Control Signal Routing
The MAX369EWN+ can route low-frequency analog control or feedback signals when several sources must feed one actuator or controller input. The 4:1 configuration is suitable for selecting command, calibration, or feedback paths without constructing multiple analog switches. The device’s TTL- and CMOS-compatible selector inputs allow a microcontroller to control channel selection directly. Because the specified on-resistance is 1.8 kOhm, include that impedance when driving a high-impedance control node or reference input, and use the manufacturer’s logic and fault-sequence guidance when changing channels under operating conditions.
Data Acquisition Front End
The MAX369EWN+ can serve as the channel-selection stage ahead of an analog-to-digital converter in a multiplexed data-acquisition front end. Two 4:1 banks provide eight analog input connections while leaving only one converter channel per multiplexer group to route. Break-before-make operation supports controlled source changes, and the 1.8 kOhm on-resistance must be included in acquisition-time and signal-accuracy analysis. Layout should minimize trace resistance and capacitance, isolate digital select lines from sensitive analog paths, and follow the manufacturer’s grounding and decoupling recommendations.
Remote Sensor Interface
The MAX369EWN+ can select remote or locally connected sensor signals before they enter a common conditioning amplifier. This application benefits from guaranteed break-before-make operation because it avoids two active sensor outputs being tied together during a switch transition. The 1.8 kOhm on-resistance can be useful with high-impedance sensor interfaces, although cable capacitance and leakage must also be evaluated. The latch and fault-protection features support defined behavior when an input develops an abnormal condition, while the dual 4:1 organization allows separate positive and differential-related routing where appropriate.
工程参考数据: MAX369EWN+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX369CWN |
|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated |
| Package | 18-SOIC | 18-SOIC |
| Product Type | Dual 4:1 fault-protected analog multiplexer with latch | Dual 4:1 fault-protected analog multiplexer with latch |
| Number of Multiplexer Circuits | 2 circuits | 2 circuits |
| On-Resistance | 1.8 kOhm | 1.8 kOhm |
| Control Logic Compatibility | TTL and CMOS compatible | TTL and CMOS compatible |
| Switching Behavior | Guaranteed break-before-make | Guaranteed break-before-make |
| Typical Power Dissipation | <7 mW | <7 mW |
关键差异点
- Confirmed same-package direct replacement (对比 MAX369CWN)
- Dual independent 4:1 routing in one device (对比 MAX369CWN)
- Controlled transitions between analog sources (对比 MAX369CWN)
- Portable-equipment power characteristics (对比 MAX369CWN)
设计说明
Include the 1.8 kOhm on-resistance in the complete source-to-load transfer function. For a resistive source, the MAX369EWN+ divides the selected signal according to the switch resistance and input impedance of the following stage. Use short analog traces, a nearby return path, and a quiet ground reference so that selector-transition coupling does not appear as a false measurement at the multiplexer output.
Route the selected analog signals away from the digital select lines and place any filtering components close to the connector or source they protect. Keep supply decoupling close to the device and follow the manufacturer’s recommended capacitor values and placement. Because this is an 18-SOIC device with sensitive analog routing, verify every terminal against the MAX369EWN pin table before assigning nets or releasing the PCB artwork.
Do not assume that two multiplexed sources can be connected safely even though the device uses break-before-make operation. External drivers, amplifiers, or test fixtures can still create contention if their outputs remain active independently of the switch. Design the system so that only one source drives a shared path at a time, and use the fault-protection and latch functions according to the manufacturer’s specified operating sequence.
Budget the switching circuit’s power loss using the manufacturer’s typical figure of less than 7 mW and the actual supply voltage, selected resistance, and load current. Estimated power in the closed switch is P = I²R, using the 1.8 kOhm on-resistance. Keep this estimate separate from the device’s total typical power-dissipation specification and verify worst-case conditions during channel transitions and fault events.
合规信息
No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 qualification statement was identified for the MAX369EWN+. The AEC-Q100 field is not applicable because this is an industrial analog interface IC rather than an automotive-qualified device.