MAX398CPE+ - 8:1 Precision Analog Multiplexer | Analog Devices
料号: MAX398CPE+ ✓ 量产中MAX398CPE+ 概述
An analog multiplexer is an integrated switching device that connects one common analog terminal to one of several channel terminals. In the broader semiconductor hierarchy, the MAX398 belongs to interface ICs, analog switches, multiplexers, and signal-routing semiconductors. Its 8:1 configuration allows eight analog inputs or outputs to share a common signal path, reducing component count in sample-and-hold systems, test equipment, signal routing, and embedded measurement circuits.
The principal features include an 8:1 single-channel architecture, low on-resistance below 100 ohms, channel-to-channel matching within 6 ohms, and flat operation over the specified analog signal range. The MAX398CPE+ is manufactured in CMOS and accepts a 3 V to 15 V supply. Its PDIP package is suitable for through-hole assemblies, socketed legacy equipment, prototype boards, and systems where a rugged replaceable package is preferred over a surface-mount option.
The multiplexer uses address-controlled selection to connect the common terminal to one of eight channels. Low and relatively consistent on-resistance helps limit signal attenuation as the selected channel changes, while the specified 11 ohm maximum variation supports predictable behavior across the analog range. These characteristics are particularly useful when the same acquisition or control circuitry handles multiple analog sources without redesigning the analog path for every input.
Typical uses include sample-and-hold circuits, heads-up displays, guidance and control systems, military radios, battery-operated systems, PBX and PABX equipment, and audio signal routing. The 3 V to 15 V supply range supports both modern low-voltage systems and legacy industrial or communications equipment, although the complete signal range must remain compatible with the device's operating limits.
Designers should place the multiplexer close to the source or destination of the analog signal to minimize PCB trace resistance and coupling. Address traces should be kept away from sensitive analog inputs, and unused control inputs should be driven to defined logic levels. Verify signal amplitude, supply voltage, and temperature against the manufacturer datasheet before substituting it into an existing assembly.
This page combines the manufacturer's architecture information, package and multiplexing details, application references, pin-compatible alternatives, and practical design guidance to support component selection and replacement decisions beyond a basic distributor specification listing.
直接替换替代料: MAX398CPE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX398CPE+ (相同外形与封装尺寸) ——差异在于 Mounting Type, ESD Protection, Multiplexer Configuration, On-Resistance, Supply Voltage Range.
MAX398CPE
✅ 直接替换📋 参考替代料(不在目录中)
DG408
✅ 直接替换联系询价
查看数据手册 →DG409DJ+
✅ 直接替换联系询价
查看数据手册 →DG508A
✅ 直接替换📋 参考替代料(不在目录中)
DG509A
✅ 直接替换📋 参考替代料(不在目录中)
HI-508APZ
✅ 直接替换📋 参考替代料(不在目录中)
MAX398CPE+ 规格参数
| Multiplexer Configuration | Single 8:1 |
| Number of Channels | 8 channels |
| On-Resistance | Less than 100 ohm |
| On-Resistance Matching Between Channels | Within 6 ohm |
| Maximum On-Resistance Variation Over Analog Signal Range | 11 ohm |
| Supply Voltage Range | 3 V to 15 V |
| Device Type | 1 circuit analog multiplexer switch |
| Technology | CMOS |
| Architecture | Precision monolithic 8-channel analog multiplexer |
| 封装 | 16-pin PDIP |
| 安装类型 | Through hole |
| Signal Routing | 8-channel to 1-channel analog routing |
| RoHS 状态 | Compliant |
MAX398CPE+ 16-pin pdip 引脚配置指南
MAX398CPE+(16-pin pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX398CPE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX398CPE+ 适用于 6 应用s: Precision Sample-and-Hold Systems, Heads-Up Display Signal Routing, Guidance and Control Systems, Military Radio Interface Circuits, PBX and PABX Audio Routing, Battery-Operated Test and Measurement.
Precision Sample-and-Hold Systems
The MAX398CPE+ fits sample-and-hold front ends that must select among eight analog sources while limiting channel-dependent error. Its on-resistance below 100 ohms, matching within 6 ohms between channels, and variation of no more than 11 ohms over the specified analog range help maintain predictable attenuation after the address controls select a channel. The 8:1 architecture consolidates eight signal sources onto one common path while the 16-pin PDIP package supports through-hole construction and socketed legacy instrumentation. Designers should account for switch on-resistance in the acquisition network, establish a defined state for every address input, and verify that source impedance and signal amplitude remain compatible with the multiplexer.
推荐
Heads-Up Display Signal Routing
The MAX398CPE+ can route one of eight analog signals into a heads-up display signal chain while preserving relatively consistent channel impedance. The manufacturer specifies on-resistance below 100 ohms, channel matching within 6 ohms, and no more than 11 ohms variation across the specified analog range, reducing differences caused merely by selecting different channels. Its single 8:1 organization allows address-controlled source selection without duplicating the downstream display driver. The PDIP package is useful in prototype, industrial, or legacy display assemblies where through-hole soldering and socket replacement are preferred. Layout should keep the common path away from switching nodes and provide defined logic levels to the address and enable pins.
推荐
Guidance and Control Systems
The MAX398CPE+ is suitable for multiplexing analog feedback or command signals within guidance and control equipment. A single 8:1 path reduces the number of signal lines reaching downstream processing electronics, while low on-resistance below 100 ohms helps limit insertion loss. Channel matching within 6 ohms and maximum on-resistance variation of 11 ohms provide useful consistency when the controller compares signals from different sources. The 3 V to 15 V operating range can support legacy command and control platforms as well as lower-voltage interface sections. Engineers should verify analog swing, control polarity, and temperature requirements against the datasheet, then keep the sensitive common trace short and away from address-switching return currents.
推荐
Military Radio Interface Circuits
The MAX398CPE+ can consolidate eight analog channels in a radio interface where a common path feeds sampling, conversion, or control circuitry. The precision on-resistance specification of below 100 ohms and channel matching within 6 ohms support consistent signal routing, while the 11 ohm maximum variation limits channel-dependent resistance changes. The through-hole PDIP-16 package also accommodates ruggedized legacy radio boards and maintenance assemblies where socketed or leaded components are operationally preferable. Because military applications may impose specific temperature, screening, and qualification requirements beyond the basic device rating, engineers must verify those requirements separately. Keep supply decoupling and address traces compact, and use controlled grounding to prevent switching transients from coupling into the selected channel.
推荐
PBX and PABX Audio Routing
The MAX398CPE+ can route one of eight low-frequency analog paths in PBX and PABX line-interface equipment. Its 8:1 architecture is useful where multiple voice or control channels share a converter or amplifier, and the sub-100 ohm on-resistance specification helps prevent excessive attenuation at the mux interface. Matching within 6 ohms and no more than 11 ohms variation across the analog range reduce channel-to-channel impedance shifts that could affect level consistency. The 16-pin PDIP format supports legacy telephone exchange boards and field-repairable through-hole assemblies. Designers should evaluate signal level, bandwidth, crosstalk, and control timing in the complete circuit, and place the mux close to the shared downstream path to minimize trace pickup.
推荐
Battery-Operated Test and Measurement
The MAX398CPE+ supports compact test and measurement equipment that must route several low-voltage sensor outputs through one acquisition channel. Its 3 V supply capability suits battery-powered systems, and the single 8:1 configuration permits eight sources to share a common analog path without using eight separate switches. On-resistance below 100 ohms, matching within 6 ohms, and variation of no more than 11 ohms help maintain predictable signal attenuation when the selected channel changes. The PDIP-16 package is practical for leaded prototypes and serviceable assemblies. Power-conscious designs should verify actual supply current and leakage for their operating mode, use a common ground reference, and keep the selected analog trace short to reduce noise pickup and additional resistance.
推荐
推荐产品汇总
工程参考数据: MAX398CPE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX398CPE | DG408 | DG409 | DG508A | DG509A | HI-508APZ |
|---|---|---|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 |
| Brand | Analog Devices | Analog Devices | Intersil | Intersil | Intersil | Intersil | Intersil |
| Multiplexer Configuration | Single 8:1 | Single 8:1 | 8:1 | 8:1 | 8:1 | 8:1 | 8:1 |
| On-Resistance | Less than 100 ohm | Less than 100 ohm | Approximately 100 ohm | Approximately 100 ohm | Approximately 100 ohm | Approximately 100 ohm | Approximately 100 ohm |
| Typical Application | Precision analog signal routing | Precision analog signal routing | Analog signal routing | Analog signal routing | Analog signal routing | Analog signal routing | Analog signal routing |
关键差异点
- Published precision channel matching (对比 DG408)
- Flat on-resistance across the analog signal range (对比 DG409)
- Low documented on-resistance (对比 HI-508APZ)
- Wide legacy-compatible supply range (对比 DG508A)
设计说明
Place the MAX398CPE+ close to the shared analog path and to the multiplexer channel being selected. The on-resistance is below 100 ohms, but PCB trace resistance adds directly to that value and can vary with copper geometry and temperature. Keep the common terminal and channel traces short, use an adequate ground reference, and avoid sharing narrow traces between the mux and sensitive downstream circuitry.
Account for the complete insertion-loss path rather than only the specified on-resistance. Use the less-than-100-ohm switch resistance together with source impedance, load impedance, and PCB trace resistance when sizing the analog network. Because channel matching is specified within 6 ohms and variation across the analog range is limited to 11 ohms, the MAX398CPE+ is well suited to circuits where switching between similar sources must not create excessive level changes.
Do not treat a shared PDIP-16 footprint as sufficient proof of interchangeability. The MAX398CPE+, DG408, DG409, DG508A, DG509A, and HI-508APZ are identified as pin-compatible options, but replacement approval should verify enable polarity, address logic, analog signal limits, supply range, operating temperature, and channel-specific functions against the manufacturer pin-description table.
Keep the address and enable traces away from the common analog terminal and sensitive channel inputs. These digital control lines can carry fast transients when the selected channel changes; maintaining separation and a stable return path reduces coupling into the selected signal. Where possible, route control signals on the opposite side of the board from high-impedance analog nodes and place supply-decoupling components near the device pins.
合规信息
The plus designation identifies the RoHS-compliant MAX398CPE+ version. No separate REACH, halogen-free, conflict-minerals, or automotive qualification statement is confirmed in the cited product information.