MC33201VD - 2.2MHz Rail-to-Rail Op Amp | onsemi | SOIC-8
料号: MC33201VD ✓ 量产中MC33201VD 概述
A rail-to-rail operational amplifier is an analog amplifier whose input and output voltage ranges extend close to the positive and negative supply rails. It belongs to the operational amplifier hierarchy within analog and signal-processing ICs, making it useful when a low-voltage system cannot support conventional amplifiers whose inputs and outputs remain farther from the supply limits. The MC33201 family is designed to preserve usable signal range in compact, single-supply equipment.
The principal operating characteristics include a 1.8 V to 12 V supply-voltage range, 2.2 MHz gain-bandwidth product, and 1 V/µs slew rate. Rail-to-rail input and output operation allows more of the available supply voltage to be used for signal conditioning. The input can be driven 200 mV beyond the supply rails without phase reversal, helping the amplifier tolerate overdrive near the rail limits. Output swing is specified to remain within 50 mV of each rail under the stated conditions.
The MC33201 is a single amplifier with one noninverting input, one inverting input, and one output. Its 8-pin SOIC package provides a conventional small-surface-mount implementation for analog boards. The combination of low minimum supply voltage, broad rail-to-rail coverage, and moderate bandwidth supports general-purpose amplification, current-voltage conversion, sensor conditioning, and filtering. These characteristics make it more appropriate for low-to-moderate frequency precision analog stages than for high-speed signal chains.
Typical applications include portable sensor interfaces, battery-powered instrumentation, low-voltage control systems, transducer signal conditioning, and audio input stages. The amplifier can operate from a 1.8 V supply, which is useful for energy-efficient systems with limited rail headroom. Its 2.2 MHz gain-bandwidth product allows moderate closed-loop bandwidth at practical gains, while the 1 V/µs slew rate supports responsive changes to waveforms within that bandwidth limit.
The principal design tradeoff is the relationship between bandwidth, supply voltage, output load, and stability. Place the device close to the feedback network and supply bypass components, keep feedback traces short, and verify the configuration against the manufacturer’s recommended compensation methods. The VD ordering code is associated with an 8-pin SOIC package, but production-temperature, tape-and-reel, and orderable-package details should be confirmed against the current onsemi product record before release.
This page organizes the MC33201VD operating envelope, verified alternatives, package and pin information, cross-reference comparisons, and practical application guidance. It also distinguishes electrical limits from package-ordering details so engineers can assess board compatibility, bandwidth, supply headroom, and thermal or sourcing constraints before selecting the amplifier.
直接替换替代料: MC33201VD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MC33201VD (相同外形与封装尺寸) ——差异在于 Product Type.
MC33201DG
✅ 直接替换📋 参考替代料(不在目录中)
MC33201DR2G
✅ 直接替换📋 参考替代料(不在目录中)
MC33201VDR2G
✅ 直接替换📋 参考替代料(不在目录中)
NCV33201VD
✅ 直接替换📋 参考替代料(不在目录中)
MC33201VD 最大额定值与电气特性
| Number of Amplifiers | 1 circuit |
| Product Type | General-purpose operational amplifier |
| Supply Voltage Range | 1.8 V to 12 V |
| Gain-Bandwidth Product | 2.2 MHz |
| Slew Rate | 1 V/µs |
| Input Common-Mode Range | Rail-to-rail |
| 输出电压范围 | Rail-to-rail |
| Maximum Input Overdrive Without Phase Reversal | 200 mV beyond the supply rails |
| Maximum Output Distance From Rail | 50 mV under specified conditions |
| 引脚数 | 8 pins |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
MC33201VD 引脚配置
| 引脚 1 | OUTA — Amplifier A output |
| 引脚 2 | INTA- — Inverting input for amplifier A |
| 引脚 3 | INTA+ — Noninverting input for amplifier A |
| 引脚 4 | V- — Negative supply connection |
| 引脚 5 | INTB+ — Noninverting input for amplifier B |
| 引脚 6 | INTB- — Inverting input for amplifier B |
| 引脚 7 | OUTB — Amplifier B output |
| 引脚 8 | V+ — Positive supply connection |
典型应用
MC33201VD 适用于 6 应用s: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Industrial Transducer Interface, Low-Voltage Audio Input Stage, Active Filtering and Feedback Control, Low-Voltage Power-Sense Conditioning.
Portable Sensor Signal Conditioning
The MC33201VD fits low-voltage sensor interfaces because it operates from 1.8 V to 12 V and accepts input signals extending to the supply-rail region. A 2.2 MHz gain-bandwidth product supports sensors with moderate bandwidth, while rail-to-rail output behavior preserves usable dynamic range in compact, battery-powered products. Place the amplifier near the sensor and feedback components to minimize noise pickup and ground offsets. Confirm the sensor’s output range and the amplifier’s offset, bias-current, and common-mode requirements before fixing the gain.
推荐
Battery-Powered Instrumentation
The MC33201VD is useful in battery-powered instrumentation where a 1.8 V minimum supply preserves signal headroom and reduces system power requirements. Its rail-to-rail inputs and outputs allow a transducer output to be amplified without requiring a bipolar supply. The 1 V/µs slew rate supports moderate-amplitude sensor transients, and the 2.2 MHz gain-bandwidth product covers many slow measurement channels. Verify output loading, common-mode range, and offset behavior at the lowest operating supply voltage before finalizing the analog front end.
推荐
Industrial Transducer Interface
The MC33201VD can amplify low-level industrial transducer signals from a 1.8 V to 12 V control system. Rail-to-rail input operation is valuable when the sensor output approaches either supply limit, and the 1 V/µs slew rate provides useful transient response for slow process signals. The 2.2 MHz gain-bandwidth product is adequate for many temperature, pressure, and position interfaces. Keep the sensor return tied to the amplifier reference properly and route high-current switching paths away from the feedback and input nodes.
推荐
Low-Voltage Audio Input Stage
The MC33201VD is appropriate for a low-voltage audio input buffer when the signal bandwidth and slew requirements are moderate. Its rail-to-rail input and output behavior allows operation close to the supply limits, while the 2.2 MHz gain-bandwidth product and 1 V/µs slew rate handle many microphone and line-level signals. Decouple the supply pins locally and use short, shielded input routing to prevent audible pickup. Avoid using the 2.2 MHz bandwidth figure as a guarantee of wideband audio performance because slew rate and output loading can become limiting.
推荐
Active Filtering and Feedback Control
The MC33201VD can implement active filters and closed-loop control stages operating from low-voltage rails. Its 2.2 MHz gain-bandwidth product permits useful closed-loop bandwidth at moderate gains, while rail-to-rail output swing improves utilization of the available supply voltage. Stability and phase margin must be checked for the exact noise gain and load rather than relying only on nominal bandwidth. Use short feedback paths, maintain symmetrical resistor layouts where practical, and include the output load in simulations before manufacturing.
推荐
Low-Voltage Power-Sense Conditioning
The MC33201VD is suitable for conditioning a scaled power or battery-sense signal before comparison and control circuitry. Operation from 1.8 V permits use in low-energy systems, and rail-to-rail input capability helps accommodate sense signals that span much of the available supply range. The 1 V/µs slew rate is more than adequate for many slow power-monitor signals. The amplifier does not replace a dedicated analog-to-converter when high resolution or sampling speed is required, but it provides a useful analog conditioning stage ahead of a controller or converter.
推荐
推荐产品汇总
工程参考数据: MC33201VD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC33201DG | MC33201DR2G | NCV33201VD | MC33202VD |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Amplifiers | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Supply Voltage Range | 1.8 V to 12 V | 1.8 V to 12 V | 1.8 V to 12 V | 1.8 V to 12 V | 1.8 V to 12 V |
| Gain-Bandwidth Product | 2.2 MHz | 2.2 MHz | 2.2 MHz | 2.2 MHz | 2.2 MHz |
| Slew Rate | 1 V/µs | 1 V/µs | 1 V/µs | 1 V/µs | 1 V/µs |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Voltage Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Input Overdrive Without Phase Reversal | 200 mV beyond the supply rails | 200 mV beyond the supply rails | 200 mV beyond the supply rails | 200 mV beyond the supply rails | 200 mV beyond the supply rails |
| Maximum Output Distance From Rail | 50 mV | 50 mV | 50 mV | 50 mV | 50 mV |
| Exact Device-Specific Stability Profile | MC33201 device profile | MC33201 device profile; suffix-specific ordering details apply | MC33201 device profile; suffix-specific ordering details apply | NCV-qualified family profile; automotive details apply | MC33202 device profile |
关键差异点
- Single-amplifier 8-pin SOIC configuration (对比 MC33202VD)
- Rail-to-rail operation from a 1.8 V supply (对比 NCV33201VD)
- Low-voltage bandwidth and transient capability (对比 MC33201DG)
设计说明
Place the MC33201VD close to the feedback components and the circuit it serves. Keep the noninverting input route short and away from switching nodes, because its high-impedance input can pick up induced noise even when the amplifier bandwidth is adequate. Connect the supply bypass capacitor directly between the local V+ and V- pins, with a short ground return. The 8-pin SOIC layout also places the two amplifier channels in a standard single-op-amp arrangement.
Validate the selected gain against the 2.2 MHz gain-bandwidth product rather than assuming the full device bandwidth is available at every closed-loop gain. Include the actual load capacitance, source resistance, and feedback network in an AC simulation. MC33201 and MC33202 can have different stability behavior, so a candidate substitution must be checked in the complete amplifier topology rather than by footprint alone.
Design the analog rail for the intended operating range of 1.8 V to 12 V, including startup and regulator tolerance. Rail-to-rail operation does not imply zero headroom: the datasheet allows input overdrive up to 200 mV beyond the rails without phase reversal and specifies output swing within 50 mV of the rails under defined conditions. Confirm the actual signal extremes and load direction before reserving the final rail margin.
Do not treat MC33201VD, MC33201DG, MC33201DR2G, and MC33201VDR2G as interchangeable without checking the onsemi ordering table. Their suffix differences can affect temperature grade, package form, marking, or shipment configuration even when the core electrical family is the same. For automotive or other regulated applications, verify qualification and traceability rather than relying on the generic MC33201 family rating.
合规信息
The onsemi MC33201 family datasheet identifies the NCV33201 series for automotive-related ordering, but exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for MC33201VD must be taken from the current manufacturer product or quality documentation.