MC33794EK Electric Field Imaging Device | NXP Semiconductors
料号: MC33794EK ✓ 量产中MC33794EK 概述
An electric field imaging device is a specialized sensor-interface IC that excites an electrode array and evaluates how objects near those electrodes disturb the generated field. The MC33794 sits within the broader hierarchy of sensor and detector interfaces, analog sensing ICs, and integrated interface circuits. Unlike a simple mechanical or optical proximity sensor, the MC33794 measures the electrical effect of a target in its field, allowing design teams to implement noncontact detection with external electrodes.
The principal features of the MC33794EK include its internally generated excitation waveform, externally adjustable operating frequency, 120 kHz optimization, and low-distortion sine-wave output. Its logic input and logic output interfaces allow a host microcontroller to configure the device and read processed sensing results. The 54-SOIC-EP package provides the pin count required for multiple electrode channels and associated control signals, while its exposed-pad construction supports improved heat transfer when the device operates continuously.
The MC33794 generates the excitation signal through an internal oscillator whose frequency is adjusted with an external resistor. NXP describes the excitation waveform as a low-frequency sine wave optimized for 120 kHz. The sensing architecture then compares the electrode field response with the generated excitation so that changes caused by nearby objects can be converted into usable logic-level information. Exact oscillator accuracy, conversion timing, channel count, and internal gain values should be confirmed in the MC33794 datasheet before setting system timing budgets.
Typical applications include touchless control panels, appliance hand-presence detection, automotive interior occupancy sensing, industrial object-position detection, and liquid or material-level measurement behind an insulating surface. Because the sensing electrodes are external, the mechanical design of the target enclosure and the electrode geometry strongly influence sensitivity. Electrode area, spacing, guard-ring layout, and isolation distance all require experimental validation in the final mechanical assembly.
For PCB implementation, follow the exposed-pad land pattern and thermal-via recommendations shown in the NXP datasheet. Decoupling capacitors should be placed directly beside the supply and ground pins, while electrode and oscillator components should be kept short and isolated from noisy switching nodes. Because the device senses very small field changes, guarding, grounding, and clean analog layout are as important as the digital interface.
This page consolidates the NXP manufacturer datasheet, distributor package information, and application-oriented engineering guidance into one structured reference. It adds pinout- and layout-verification instructions, comparison rows for qualified alternatives, and practical sensor-layout guidance that engineers would otherwise need to piece together from multiple documents.
直接替换替代料: MC33794EK ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MC33794EF
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MC33794EK/R2
✅ 直接替换📋 参考替代料(不在目录中)
MC33794E
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MC33794EK 规格参数
| Device Type | Electric field imaging device |
| Sensor Interface Type | Logic input, logic output |
| Number of Terminals | 54 |
| 封装 | 54-SOIC-EP |
| Package Body Width | 7.50 mm |
| Package Length | 0.295 inch |
| 安装类型 | Surface mount |
| 电源电流 | 7 mA |
| Excitation Signal | Low-frequency sine wave |
| Optimized Excitation Frequency | 120 kHz |
| Frequency Adjustment | External resistor |
| 工作温度范围 | -40C to +85C |
| Temperature Grade | Industrial |
| Packaging | Tube |
| 接口 | ISO9141 |
| Package Shape | Rectangular |
MC33794EK rectangular 引脚配置指南
MC33794EK(rectangular 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MC33794EK.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC33794EK 适用于 6 应用s: Noncontact Touchless Controls, Appliance Hand-Presence Detection, Automotive Interior Presence Detection, Liquid Level Sensing Behind Insulation, Industrial Object Presence and Positioning, Material Presence and Through-Wall Detection.
Noncontact Touchless Controls
The MC33794EK is suited to touchless user interfaces because external electrodes can detect a finger approaching a sealed panel without mechanical contact. Its internally generated sine-wave excitation and logic interface provide a defined path from field measurement to host-controller decision. Place the electrodes behind a nonconductive fascia and evaluate sensitivity against panel thickness, moisture, and grounding. Unlike a mechanical pushbutton, the approach can eliminate moving contacts while preserving a sealed front surface.
Appliance Hand-Presence Detection
The MC33794EK can detect a user's hand near an appliance door or control panel, allowing functions to start only when a person is present. Its -40C to +85C range covers many appliance and industrial environments, while the 7 mA supply current supports low-power system designs. Electrode geometry should be tuned to the distance where activation is required, and the logic output can be combined with a timer in the host controller to avoid unintended restarts.
Automotive Interior Presence Detection
The MC33794EK supports noncontact presence detection inside a vehicle cabin, where seat occupancy, console touch, or door-interior sensing is required. Its external electrodes can be integrated into trim surfaces, and the 54-SOIC-EP package provides a controlled, repeatable mounting solution. Engine-start or safety-related functions additionally require automotive qualification verification, EMC validation, transient protection, and a documented fault strategy rather than reliance on the temperature rating alone.
Liquid Level Sensing Behind Insulation
The MC33794EK can be evaluated for level detection when electrodes are mounted outside a nonmetallic vessel. The device excites the electrode field and detects changes associated with the material above or below a target boundary. Performance depends on liquid conductivity, dielectric constant, wall thickness, and electrode spacing, so each tank design requires calibration. The noncontact arrangement avoids inserting a probe into the fluid and reduces maintenance, but it must also tolerate changing dielectric properties.
Industrial Object Presence and Positioning
The MC33794EK fits industrial systems that need to confirm whether a part is present in a fixture or positioned near a process area. External electrodes can be positioned around plastic guards and tooling to create a controlled sensing field without touching precision parts. The MC33794 logic interface allows a PLC or embedded controller to evaluate the result. Because nearby metal, cables, and moving fixtures alter field coupling, final sensitivity must be established with the production mechanical assembly in place.
Material Presence and Through-Wall Detection
The MC33794EK can support material-presence checks where an object must be identified through a thin insulating barrier. The excitation and sensing electrodes operate from the same IC platform, reducing the need for a separate analog oscillator. Compared with optical detection, an electric field approach can work without a clear line of sight, although the barrier material and object conductivity still control coupling. Design validation should sweep target position and temperature to establish reliable detection thresholds.
工程参考数据: MC33794EK ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC33794EF | MC33794EK/R2 | MC33794E |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 54-SOIC-EP | 54-SOIC-EP | 54-SOIC-EP | 54-SOIC-EP |
| Terminal Count | 54 | 54 | 54 | 54 |
| Device Function | Electric field imaging device | Electric field imaging device | Electric field imaging device | Electric field imaging device |
| Excitation Signal | Low-frequency sine wave | Low-frequency sine wave | Low-frequency sine wave | Low-frequency sine wave |
| Optimized Frequency | 120 kHz | 120 kHz | 120 kHz | 120 kHz |
| Supply Current | 7 mA | 7 mA | 7 mA | 7 mA |
| Operating Temperature Range | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Input Interface | Logic | Logic | Logic | Logic |
| Output Interface | Logic | Logic | Logic | Logic |
关键差异点
- Integrated electric field excitation and sensing interface (对比 MC33794EF)
- Wide industrial operating range (对比 MC33794E)
- High pin count for electrode and control connectivity (对比 MC33794EK/R2)
设计说明
Place input and output decoupling capacitors directly beside their corresponding supply and ground pins, and keep the traces short. The MC33794 senses small electric-field changes, so routing the electrode and oscillator area near switching converters, relays, or high-current return paths can raise noise and produce false detections. Use a continuous ground reference beneath the analog section and connect the exposed pad to ground through the package-recommended thermal-via pattern.
Design the external electrodes as part of the mechanical system rather than as isolated copper shapes. Electrode area, spacing, overlap, guard structures, and the dielectric distance to the target directly determine field coupling and sensitivity. Model a nominal geometry, fabricate several variations if necessary, and calibrate each mechanical revision because a change in enclosure material can shift detection thresholds as much as an electrical component change.
Do not assume that a catalog-level 120 kHz optimization guarantees a fixed operating frequency in every circuit. The excitation frequency is adjusted with an external resistor, and component tolerance, temperature, and the surrounding electrode network can affect the final signal. Follow the manufacturer reference circuit and component-selection guidance, then measure the waveform at the relevant pins in the assembled product before setting software thresholds.
合规信息
The verified product information identifies the MC33794EK as an industrial-temperature electric field imaging device but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm current declarations with NXP before release to a regulated market.