MC33895FC - LIN Bus Transceiver | NXP | 32-QFN
料号: MC33895FC ✓ 量产中MC33895FC 概述
A LIN transceiver is an interface IC within the broader automotive networking hierarchy. LIN, or Local Interconnect Network, is a low-cost, single-wire serial protocol commonly used for distributed vehicle subsystems and industrial control networks. The MC33895FC occupies the physical interface position between digital logic and the bus wiring, allowing higher-level firmware and controller hardware to exchange data through the LIN physical layer.
The principal documented packaging characteristics are a 32-QFN case, surface mounting, and tube packing. A QFN package supports compact PCB layouts and exposes a pad beneath the device for thermal coupling to the board. The exposed pad is therefore an important layout feature rather than an additional electrical signal. Because the MC33895FC is intended for space-constrained automotive and industrial electronics, this package balances mechanical compactness with a practical thermal and assembly footprint.
The MC33895FC is classified as a LIN transceiver, placing it within integrated interface semiconductors rather than processors, memory, or discrete communication components. Its system role requires compatibility with the LIN controller, microcontroller, bus termination strategy, supply architecture, and connector wiring of the target ECU or controller board. Designers should review the device documentation before assigning wake-up, fault-handling, supply, ground, and transceiver-enable functions to package pins.
Typical uses include vehicle body and comfort electronics, sensor interfaces, local actuator controllers, industrial control modules, and distributed embedded systems. In each case, the transceiver supports communication over a LIN network while the attached controller handles protocol framing and application behavior. Its 32-QFN exposed-pad construction is useful where component density is important and board area is constrained.
PCB implementation should place the transceiver close to the LIN connection and route the bus as a controlled single-wire network. Power and ground connections require careful layout according to the manufacturer pin description and recommended application circuit. The exposed pad should be connected using the prescribed land pattern and thermal strategy rather than treated as an interchangeable mechanical feature.
This page combines the exact catalog identity, package information, sourcing references, application guidance, and selection considerations for MC33895FC. It is designed to help engineers move from part identification to datasheet review, footprint validation, interface design, and prototype assembly while avoiding unsupported electrical assumptions.
直接替换替代料: MC33895FC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料MC33895FC 规格参数
| Product Type | LIN bus transceiver |
| Communication Protocol | LIN |
| 引脚数 | 32 pins |
| 封装 | 32-QFN with exposed pad |
| 安装方式 | Surface Mount |
| Packaging | Tube |
| Product Category | Drivers, Receivers, Transceivers |
| Application Domain | Automotive and industrial LIN communication |
| Bus Type | Single-wire LIN bus |
MC33895FC 32-qfn with exposed pad 引脚配置指南
MC33895FC(32-qfn with exposed pad 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MC33895FC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC33895FC 适用于 6 应用s: Vehicle Body Control Modules, Automotive Sensor Nodes, Industrial Distributed Control, Local Actuator Controllers, Switch and Lighting Modules, Communication and Network Gateways.
Vehicle Body Control Modules
The MC33895FC fits vehicle body-control modules that connect a LIN-capable microcontroller to switches, sensors, or actuators distributed across a single-wire LIN subnetwork. Its 32-QFN exposed-pad package reduces PCB footprint, while surface mounting supports automated automotive electronics assembly. The transceiver handles the physical communication interface, leaving protocol framing and application logic to the controller. During implementation, verify supply limits, LIN timing, bus-capacitance limits, wake-up behavior, fault handling, and exposed-pad thermal requirements against the module’s operating environment.
推荐
Automotive Sensor Nodes
The MC33895FC can provide the LIN physical-layer interface in a remote automotive sensor node that reports measurements to a central body or chassis controller. The 32-QFN format is valuable where connector spacing, component density, and board area limit the enclosure design. A host microcontroller or dedicated LIN controller performs protocol handling while the MC33895FC connects that logic to the bus. Designers should confirm wake-up and sleep behavior, electrical thresholds, ESD requirements, bus topology, and thermal performance for each mounting position.
推荐
Industrial Distributed Control
The MC33895FC is suitable for industrial distributed-control modules that use LIN as a low-cost single-wire communication network among sensors, actuators, and local controllers. Its compact 32-QFN exposed-pad package supports dense controller boards, and its documented automotive and industrial positioning fits equipment requiring a dedicated physical-layer interface. The MCU handles addressable communication and control logic, while the transceiver connects it to the bus. Review electrical limits, timing, protection, operating temperature, and qualification for the installed machinery before production release.
推荐
Local Actuator Controllers
The MC33895FC can be used in a local actuator controller that accepts commands over a LIN subnetwork and drives a motor, valve, latch, or indicator through separate power circuitry. Its role is limited to the communication interface, allowing the main controller to remain independent of the LIN physical layer. The compact 32-QFN exposed-pad package helps when the actuator controller must fit behind a connector or within a small enclosure. Validate bus timing, supply sequencing, sleep current, fault recovery, thermal exposure, and the recommended application circuit before deployment.
推荐
Switch and Lighting Modules
The MC33895FC fits compact switch and lighting modules that receive commands over LIN and report switch position, lamp status, or diagnostic information. A LIN-capable controller manages scheduled communication, while the transceiver provides the physical connection to the vehicle or industrial wiring. The 32-QFN package supports dense multi-function modules without requiring a larger through-hole interface. Engineers should confirm logic levels, wake-up strategy, bus termination requirements, ESD protection, output timing, and exposed-pad construction before approving the module for production.
推荐
Communication and Network Gateways
The MC33895FC can serve as a LIN-facing interface within a gateway that translates or aggregates data from a LIN subnetwork. The gateway’s processor or microcontroller manages protocol conversion and system behavior, while the transceiver connects the board to the physical bus. Surface mounting and the 32-QFN exposed-pad package make the device appropriate for compact embedded gateways. The design must follow the manufacturer’s application circuit, maintain suitable bus routing and termination, provide required filtering and protection, and verify timing and electrical limits under the expected network loading.
推荐
推荐产品汇总
工程参考数据: MC33895FC ——对比、设计指导和合规信息。
选型指南
设计说明
Create the MC33895FC footprint from the manufacturer package drawing rather than a generic 32-QFN library entry. Verify pad dimensions, exposed-pad geometry, solder-mask opening, paste pattern, pin numbering, and courtyard clearance. The exposed pad is a package feature with both electrical and thermal implications, so it should not be replaced by a conventional peripheral lead or left unconnected unless the manufacturer instructions explicitly require it.
Place the transceiver and its supporting network close to the LIN connector or bus entry point. Keep the bus route away from sensitive clocks, sensor inputs, and switching-power nodes, and follow the recommended application circuit for filtering, pull-up behavior, and protection. Correct pin assignment, reference-designator mapping, and bus polarity are more important than visually matching another 32-QFN component.
Treat the exposed pad as the principal package heat-transfer feature. Follow the manufacturer's recommended copper and solder-land geometry, and use the PCB stack-up and thermal data when estimating junction temperature. Actual dissipation depends on supply voltage, bus activity, and internal operating conditions, so thermal validation should combine calculated loss with board-level temperature measurement in the final enclosure.
Do not select a replacement solely because it uses a 32-QFN package. Verify the complete 32-pin signal map, exposed-pad connection, supply range, LIN thresholds, timing, sleep and wake behavior, bus protection, fault response, and application-circuit recommendations. Tube packaging also requires attention to moisture protection, floor life, baking, ESD controls, and the component's reflow profile.
合规信息
The catalog data identifies automotive and industrial applications but does not provide specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Review the manufacturer product documentation and obtain current supporting declarations for the exact ordering option.