NXP Semiconductors

MC33895FC - LIN Bus Transceiver | NXP | 32-QFN

MPN: MC33895FC ✓ Active
32-QFN with exposed pad Package
MOQ: 1 |

MC33895FC Overview

The NXP Semiconductors MC33895FC is a high-speed LIN bus transceiver packaged in a 32-QFN surface-mount package with an exposed pad. It serves as the interface between a LIN controller or host microcontroller and the physical LIN network, combining digital communication functions with the physical-layer circuitry required for reliable single-wire bus communication. The component is identified for automotive and industrial applications where a compact transceiver is needed to connect an embedded controller to a LIN network.

A LIN transceiver is an interface IC within the broader automotive networking hierarchy. LIN, or Local Interconnect Network, is a low-cost, single-wire serial protocol commonly used for distributed vehicle subsystems and industrial control networks. The MC33895FC occupies the physical interface position between digital logic and the bus wiring, allowing higher-level firmware and controller hardware to exchange data through the LIN physical layer.

The principal documented packaging characteristics are a 32-QFN case, surface mounting, and tube packing. A QFN package supports compact PCB layouts and exposes a pad beneath the device for thermal coupling to the board. The exposed pad is therefore an important layout feature rather than an additional electrical signal. Because the MC33895FC is intended for space-constrained automotive and industrial electronics, this package balances mechanical compactness with a practical thermal and assembly footprint.

The MC33895FC is classified as a LIN transceiver, placing it within integrated interface semiconductors rather than processors, memory, or discrete communication components. Its system role requires compatibility with the LIN controller, microcontroller, bus termination strategy, supply architecture, and connector wiring of the target ECU or controller board. Designers should review the device documentation before assigning wake-up, fault-handling, supply, ground, and transceiver-enable functions to package pins.

Typical uses include vehicle body and comfort electronics, sensor interfaces, local actuator controllers, industrial control modules, and distributed embedded systems. In each case, the transceiver supports communication over a LIN network while the attached controller handles protocol framing and application behavior. Its 32-QFN exposed-pad construction is useful where component density is important and board area is constrained.

PCB implementation should place the transceiver close to the LIN connection and route the bus as a controlled single-wire network. Power and ground connections require careful layout according to the manufacturer pin description and recommended application circuit. The exposed pad should be connected using the prescribed land pattern and thermal strategy rather than treated as an interchangeable mechanical feature.

This page combines the exact catalog identity, package information, sourcing references, application guidance, and selection considerations for MC33895FC. It is designed to help engineers move from part identification to datasheet review, footprint validation, interface design, and prototype assembly while avoiding unsupported electrical assumptions.

Drop-in alternatives for MC33895FC — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

No drop-in alternatives available for this product.

Request Alternatives

MC33895FC Specifications

Product Type LIN bus transceiver
Communication Protocol LIN
Number of Pins 32 pins
Package 32-QFN with exposed pad
Mounting Style Surface Mount
Packaging Tube
Product Category Drivers, Receivers, Transceivers
Application Domain Automotive and industrial LIN communication
Bus Type Single-wire LIN bus

MC33895FC 32-qfn with exposed pad Pin Configuration Guide

Pin configuration for MC33895FC (32-qfn with exposed pad package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

32-qfn with exposed pad package pinout diagram for MC33895FC

No detailed pinout data available for MC33895FC.

Refer to the datasheet for full pin configuration.

Typical Applications

MC33895FC is suitable for 6 applications: Vehicle Body Control Modules, Automotive Sensor Nodes, Industrial Distributed Control, Local Actuator Controllers, Switch and Lighting Modules, Communication and Network Gateways.

🚗

Vehicle Body Control Modules

The MC33895FC fits vehicle body-control modules that connect a LIN-capable microcontroller to switches, sensors, or actuators distributed across a single-wire LIN subnetwork. Its 32-QFN exposed-pad package reduces PCB footprint, while surface mounting supports automated automotive electronics assembly. The transceiver handles the physical communication interface, leaving protocol framing and application logic to the controller. During implementation, verify supply limits, LIN timing, bus-capacitance limits, wake-up behavior, fault handling, and exposed-pad thermal requirements against the module’s operating environment.

🧩

Automotive Sensor Nodes

The MC33895FC can provide the LIN physical-layer interface in a remote automotive sensor node that reports measurements to a central body or chassis controller. The 32-QFN format is valuable where connector spacing, component density, and board area limit the enclosure design. A host microcontroller or dedicated LIN controller performs protocol handling while the MC33895FC connects that logic to the bus. Designers should confirm wake-up and sleep behavior, electrical thresholds, ESD requirements, bus topology, and thermal performance for each mounting position.

🏭

Industrial Distributed Control

The MC33895FC is suitable for industrial distributed-control modules that use LIN as a low-cost single-wire communication network among sensors, actuators, and local controllers. Its compact 32-QFN exposed-pad package supports dense controller boards, and its documented automotive and industrial positioning fits equipment requiring a dedicated physical-layer interface. The MCU handles addressable communication and control logic, while the transceiver connects it to the bus. Review electrical limits, timing, protection, operating temperature, and qualification for the installed machinery before production release.

⚙️

Local Actuator Controllers

The MC33895FC can be used in a local actuator controller that accepts commands over a LIN subnetwork and drives a motor, valve, latch, or indicator through separate power circuitry. Its role is limited to the communication interface, allowing the main controller to remain independent of the LIN physical layer. The compact 32-QFN exposed-pad package helps when the actuator controller must fit behind a connector or within a small enclosure. Validate bus timing, supply sequencing, sleep current, fault recovery, thermal exposure, and the recommended application circuit before deployment.

💡

Switch and Lighting Modules

The MC33895FC fits compact switch and lighting modules that receive commands over LIN and report switch position, lamp status, or diagnostic information. A LIN-capable controller manages scheduled communication, while the transceiver provides the physical connection to the vehicle or industrial wiring. The 32-QFN package supports dense multi-function modules without requiring a larger through-hole interface. Engineers should confirm logic levels, wake-up strategy, bus termination requirements, ESD protection, output timing, and exposed-pad construction before approving the module for production.

🌐

Communication and Network Gateways

The MC33895FC can serve as a LIN-facing interface within a gateway that translates or aggregates data from a LIN subnetwork. The gateway’s processor or microcontroller manages protocol conversion and system behavior, while the transceiver connects the board to the physical bus. Surface mounting and the 32-QFN exposed-pad package make the device appropriate for compact embedded gateways. The design must follow the manufacturer’s application circuit, maintain suitable bus routing and termination, provide required filtering and protection, and verify timing and electrical limits under the expected network loading.

What is the MC33895FC?
The MC33895FC is an NXP Semiconductors high-speed LIN bus transceiver in a 32-QFN surface-mount package with an exposed pad. It provides the physical interface between a LIN-capable controller or microcontroller and a LIN network. The catalog identifies LIN communication, automotive and industrial use, and tube packaging, making it suitable for compact distributed control modules.
What package does the MC33895FC use?
The MC33895FC uses a 32-QFN package with an exposed pad. Its exposed-pad construction supports compact surface-mount layouts and provides a defined thermal-coupling feature beneath the package. The manufacturer pin description and land-pattern guidance must be followed when assigning pins and connecting the pad, because the exposed pad is not interchangeable with an ordinary package lead.
How is MC33895FC packaged for shipment?
The MC33895FC is identified as being packaged in a tube. Tube packaging is intended for automated or semi-automated production feeding and should be handled according to moisture-protection and ESD-control procedures. Before assembly, confirm the exact ordering option, bake requirements, floor-life information, and exposed-pad soldering profile in the manufacturer documentation.
What is the difference between the MC33895FC and a LIN controller?
The MC33895FC is the physical-layer transceiver, while a LIN controller implements higher-level framing, scheduling, and data handling. The transceiver connects controller or microcontroller logic to the single-wire LIN bus. Both devices are normally required in an ECU, although some embedded controllers integrate compatible LIN-interface functions.
Can MC33895FC be used in industrial control systems?
Yes, the MC33895FC is identified for automotive and industrial applications involving LIN communication. It can be selected for compact industrial controllers, sensor modules, and distributed control units that use LIN as a low-cost single-wire network. Electrical limits, supply range, bus timing, protection ratings, and environmental qualifications should be checked against the target system conditions.
What are the key specifications of MC33895FC that engineers should know?
The MC33895FC is a LIN transceiver with three defining catalog characteristics: 32-QFN packaging with an exposed pad, surface-mount assembly, and tube packing. It is positioned for automotive and industrial communications. Its bus role makes it suitable for LIN-capable microcontrollers, distributed vehicle electronics, and industrial control nodes requiring a dedicated physical-layer transceiver.
Where can I download the MC33895FC datasheet PDF?
The MC33895FC manufacturer datasheet is available through NXP's datasheet library at https://www.nxp.com/docs/en/data-sheet/MC33895.pdf. Use that document for the authoritative pin descriptions, electrical characteristics, timing diagrams, recommended application circuit, exposed-pad connection, operating limits, and qualification information before releasing a PCB design.
Where can I find the MC33895FC pinout?
The MC33895FC pinout is documented in the NXP MC33895 datasheet, beginning with the pin-description and package drawings. The component has 32 QFN pins plus a thermal exposed pad, so schematic capture and PCB-library creation should distinguish individual signal pins from the exposed-pad connection. Assign every signal strictly from the datasheet rather than inferring functions from a generic LIN transceiver.
What can replace the MC33895FC?
The MC33895FC should be replaced only with a part whose complete pin definition, electrical limits, LIN timing, supply requirements, exposed-pad layout, and automotive qualifications have been checked. No verified drop-in substitute was identified in the available cross-reference results, so a generic 32-QFN LIN transceiver should not be assumed to be interchangeable. Use the NXP cross-reference process or manufacturer guidance for an approved substitution.
Is MC33895FC the same as another 32-QFN LIN transceiver?
No. A shared 32-QFN package does not by itself make two LIN transceivers interchangeable. The MC33895FC has a defined 32-QFN exposed-pad footprint, but replacement also requires matching pin functions, supply range, LIN levels, timing, sleep and wake behavior, fault handling, protection, and qualification. Confirm those parameters in both datasheets before treating any part as equivalent.
MC33895FC versus a generic LIN transceiver: which is better for an automotive ECU?
The MC33895FC is the better-supported starting point for an automotive or industrial LIN ECU because its catalog identity explicitly includes automotive and industrial use, a 32-QFN exposed-pad package, surface mounting, and tube packing. A generic LIN transceiver is preferable only if it satisfies every electrical, timing, layout, protection, and qualification requirement. Package similarity alone is not sufficient.
When should I choose the MC33895FC over another LIN interface?
Choose the MC33895FC when the design benefits from its documented 32-QFN exposed-pad footprint and the intended automotive or industrial LIN role. It is especially relevant where board area is constrained and surface-mount assembly is required. Select another interface if it offers a needed function, wider electrical range, smaller footprint, or qualification not present in the MC33895FC documentation.
Is the MC33895FC suitable for a distributed sensor module?
The MC33895FC can suit a distributed sensor module that uses LIN and needs a compact surface-mount transceiver. Its single-wire bus role allows a microcontroller to communicate with a remote sensor or actuator node. Confirm supply behavior, sleep requirements, bus capacitance, ESD exposure, wake-up capability, and the exposed-pad thermal design for the enclosure and environment.
How should the MC33895FC exposed pad be handled on a PCB?
The MC33895FC exposed pad should be implemented using the manufacturer land pattern and the documented electrical and thermal connection method. Preserve the pad geometry, define its net assignment according to the application guidance, and use an appropriate solder mask and paste strategy. Follow the component's reflow profile and assembly-handling requirements to avoid voiding or weak thermal coupling.
Where can I request a quote and current lead time for MC33895FC?
Use the Request a Quote form on this page to request MC33895FC pricing, stock confirmation, lead time, and ordering details. Current commercial terms should be confirmed through the quote process rather than inferred from historical catalog records. Specify the exact MPN, required quantity, tube packaging requirement, shipment destination, and any date-sensitive production schedule.
What is the lead time for MC33895FC?
Current MC33895FC lead time depends on supplier inventory, order quantity, packaging requirements, and production demand. Use the Request a Quote form on this page with the required quantity and delivery date to obtain a current commitment. For production planning, request confirmation of factory or authorized-channel supply, date-code continuity, and any change-control information.
Is MC33895FC in stock and what does it cost?
Current MC33895FC availability and commercial pricing should be confirmed through the Request a Quote form on this page. Submit the exact MPN, required quantity, tube packaging requirement, and shipment location. The form provides the appropriate route for current supply, lead-time, and quote information without relying on potentially stale catalog or listing data.
Which compliance documents should be reviewed for MC33895FC?
Review the manufacturer product page and datasheet for the current RoHS, REACH, halogen-free, conflict-minerals, and automotive-qualification statements applicable to the exact ordering option. The MC33895FC catalog identity confirms an automotive and industrial application position but does not by itself establish a specific compliance certification. Request supporting declarations from the supplier when your program requires them.

Engineering reference data for MC33895FC — comparison, design guidance, and compliance information.

Selection Guide

Choose the MC33895FC when the target design requires a dedicated LIN physical-layer transceiver and can use a 32-QFN exposed-pad footprint. It is particularly relevant to compact automotive or industrial controller boards assembled by surface-mount production and distributed across multiple LIN nodes. The part is not a protocol controller, so it should be paired with a LIN-capable microcontroller or controller. Do not substitute based only on package size: any alternative must match the complete pin arrangement, exposed-pad treatment, electrical thresholds, timing, sleep and wake behavior, fault handling, protection requirements, and required automotive qualification. Because no verified drop-in alternatives were identified, production continuity planning should rely on manufacturer cross-reference and supply-channel confirmation rather than an unverified compatible-looking device.

Design Notes

Create the MC33895FC footprint from the manufacturer package drawing rather than a generic 32-QFN library entry. Verify pad dimensions, exposed-pad geometry, solder-mask opening, paste pattern, pin numbering, and courtyard clearance. The exposed pad is a package feature with both electrical and thermal implications, so it should not be replaced by a conventional peripheral lead or left unconnected unless the manufacturer instructions explicitly require it.

Place the transceiver and its supporting network close to the LIN connector or bus entry point. Keep the bus route away from sensitive clocks, sensor inputs, and switching-power nodes, and follow the recommended application circuit for filtering, pull-up behavior, and protection. Correct pin assignment, reference-designator mapping, and bus polarity are more important than visually matching another 32-QFN component.

Treat the exposed pad as the principal package heat-transfer feature. Follow the manufacturer's recommended copper and solder-land geometry, and use the PCB stack-up and thermal data when estimating junction temperature. Actual dissipation depends on supply voltage, bus activity, and internal operating conditions, so thermal validation should combine calculated loss with board-level temperature measurement in the final enclosure.

Do not select a replacement solely because it uses a 32-QFN package. Verify the complete 32-pin signal map, exposed-pad connection, supply range, LIN thresholds, timing, sleep and wake behavior, bus protection, fault response, and application-circuit recommendations. Tube packaging also requires attention to moisture protection, floor life, baking, ESD controls, and the component's reflow profile.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The catalog data identifies automotive and industrial applications but does not provide specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Review the manufacturer product documentation and obtain current supporting declarations for the exact ordering option.

Data verified on: 2026-11-11 — data verified and curated by XAIPART's component engineering team

Related Searches

MC33895FC datasheet MC33895FC datasheet pdf MC33895FC pinout MC33895FC 32-QFN footprint MC33895FC LIN transceiver NXP MC33895FC MC33895FC equivalent MC33895FC replacement MC33895FC drop-in substitute MC33895FC cross reference MC33895FC automotive ECU MC33895FC price MC33895FC stock MC33895FC lead time

Related Components & Terms

NXP Semiconductors MC33895FC LIN bus LIN transceiver Local Interconnect Network automotive networking industrial control single-wire serial bus physical-layer interface LIN controller microcontroller embedded control 32-QFN QFN package family exposed pad surface-mount package tube packaging distributed control module vehicle body control sensor node actuator controller communication gateway ESD protection bus termination
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details