MC3486DG4 - Quad RS-422/423 Receiver | Texas Instruments
料号: MC3486DG4 ✓ 量产中MC3486DG4 概述
A differential line receiver is an interface IC that converts a balanced differential signal arriving over a cable into a logic-level output for a digital system. The MC3486 belongs to the receiver category within the broader line-driver and transceiver hierarchy. Its four independent channels allow one device to terminate and decode four differential inputs, reducing component count in multi-channel data acquisition, industrial control, and communications equipment.
The principal features include four receiver channels, three-state outputs, TTL-compatible signaling, and operation from a nominal 5 V supply. The listed maximum receive delay is 35 ns, making the device suitable for systems that require rapid recovery of differential data from balanced lines. Its commercial temperature grade extends from 0 °C to 70 °C, while the 16-SOIC package supports conventional surface-mount PCB assembly.
Each receiver channel uses differential input signaling to reject common-mode voltage present on cabling and grounding environments. Three-state outputs permit the output pins to enter a high-impedance state when the system needs to share a data bus or isolate a receiver. The MC3486 therefore combines standard RS-422 and RS-423 reception with bus-oriented output control rather than functioning as a simple single-ended logic receiver.
Typical applications include industrial serial interfaces, test and measurement systems, data acquisition equipment, and legacy computer peripherals that communicate over balanced differential lines. Four channels make the device especially useful where multiple cable-connected sensors, controllers, or peripheral boards must feed a common digital processor. The 5 V operating range also allows the receiver to operate alongside conventional TTL and CMOS interface logic when appropriate voltage compatibility is maintained.
Designers should verify receiver enable and output-state timing against the system clock, preserve adequate differential signal margin at the cable interface, and account for connector and cable characteristics. The 35 ns maximum receive delay is a useful timing boundary when calculating setup-and-hold margins or supporting legacy peripheral clocking. Decoupling should follow the connection recommendations in the manufacturer datasheet.
This product page combines the device architecture, interface standards, timing information, verified drop-in candidates, package considerations, and practical application guidance. It also distinguishes confirmed replacement options from parts that require additional qualification, helping engineers narrow a design without confusing protocol compatibility with complete production suitability.
直接替换替代料: MC3486DG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MC3486DG4 (相同外形与封装尺寸) ——差异在于 Operating Temperature Range, Output Type, Package.
MC3486DR
✅ 直接替换联系询价
查看数据手册 →MC3486D
✅ 直接替换联系询价
查看数据手册 →DS3486M
✅ 直接替换📋 参考替代料(不在目录中)
DS3486MX
✅ 直接替换📋 参考替代料(不在目录中)
MC3486DG4 规格参数
| Receiver Type | Quadruple differential line receiver |
| Number of Receivers | 4 |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| Supported Protocols | RS-422 and RS-423 |
| ANSI Standard | TIA/EIA-422-B and TIA/EIA-423-B |
| ITU Recommendations | V.10 and V.11 |
| Maximum Receive Delay | 35 ns |
| 输出类型 | 3-state, TTL-compatible |
| 封装 | 16-pin SOIC, 3.90 mm width |
| 安装类型 | Surface mount |
| 工作温度范围 | 0 °C to 70 °C |
| Packaging | Tube |
MC3486DG4 16-pin soic, 3.90 mm width 引脚配置指南
MC3486DG4(16-pin soic, 3.90 mm width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MC3486DG4.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC3486DG4 适用于 6 应用s: Industrial Differential Data Acquisition, Test and Measurement Instrumentation, Legacy Peripheral Communications, Multi-Channel Sensor Interface, Process Control Communication Interfaces, Communication Backplane and Bus Isolation.
Industrial Differential Data Acquisition
The MC3486DG4 fits acquisition systems that must convert four balanced cable connections into digital logic signals for a controller or processor. Its four independent differential receiver channels reduce the number of separate receiver packages, while the 4.75 V to 5.25 V supply range supports conventional 5 V interface electronics. The receiver architecture targets ANSI TIA/EIA-422-B and TIA/EIA-423-B signaling, including ITU V.10 and V.11 recommendations. Because the maximum receive delay is 35 ns, timing analysis should include the complete input path rather than relying only on nominal propagation delay. Cable termination, common-mode conditions, and protection devices must be selected for the installation environment.
推荐
Test and Measurement Instrumentation
Instrumentation with several remote probes or fixture modules can use the MC3486DG4 to receive four balanced signals through a shared interface IC. The device converts differential RS-422 or RS-423 inputs into TTL-compatible outputs, allowing a measurement controller to read multiple channels through a defined interface standard. Its 35 ns maximum receive delay provides a concrete timing limit for synchronizing returned data with acquisition logic. Three-state outputs add flexibility when multiple interface sections must be isolated or share a bus. The 0 °C to 70 °C commercial temperature range suits controlled laboratory and production-test environments where full automotive temperature coverage is unnecessary.
推荐
Legacy Peripheral Communications
The MC3486DG4 is appropriate for legacy computer peripherals and industrial controllers that use balanced differential communications instead of single-ended logic. Four receiver sections can decode status, command acknowledgment, data, and control lines from one 16-SOIC package. Compatibility with TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 makes it useful when the equipment interface is based on established balanced-line recommendations. The TTL-compatible outputs can interface with suitable 5 V digital logic, but designers must verify input thresholds, enable polarity, and timing in the connected legacy system. Cable routing, grounding, and termination remain essential to reliable reception.
推荐
Multi-Channel Sensor Interface
A sensor interface requiring several differential readings can place the MC3486DG4 between remote sensor lines and a digital acquisition controller. Four balanced inputs reduce package count compared with four single-channel receivers, while differential reception helps reject common-mode voltage present in industrial wiring. The nominal 5 V operation and TTL-compatible outputs align with many legacy control boards, while the 35 ns receive-delay ceiling helps define setup and hold margins. This use requires the engineer to verify that sensor signal amplitudes, common-mode limits, and bandwidth remain within the receiver electrical characteristics. Protection, termination, and isolation should also be evaluated for cable-connected sensors.
推荐
Process Control Communication Interfaces
Process-control equipment often distributes data between controllers, remote I/O, and operator panels over balanced wiring. The MC3486DG4 can receive four differential signals simultaneously, providing a compact interface between those remote nodes and a 5 V control processor. Its support for both RS-422 and RS-423 is useful where equipment uses the two related standards, while three-state outputs can assist with controlled bus isolation. The commercial temperature grade of 0 °C to 70 °C fits ordinary indoor control cabinets. System designers should account for the stated 35 ns receive delay, enable timing, cable characteristics, and any grounding or surge-protection requirements in the installation environment.
推荐
Communication Backplane and Bus Isolation
The MC3486DG4 can serve backplane systems that need several differential inputs with controllable output states. Its three-state outputs permit a receiver to be disconnected electrically when it is not selected, which is valuable when several interface sections share routing or when a system requires controlled isolation during reset. Four receiver channels and a 16-SOIC package provide moderate board-area savings over discrete implementations. The receiver supports ANSI TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 signaling, but the complete backplane must preserve the required differential impedance, termination, and signal integrity. Timing around enable and output-disable transitions should be checked at the system level.
推荐
推荐产品汇总
工程参考数据: MC3486DG4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC3486DR | MC3486D | DS3486M | DS3486MX |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Number of Receivers | 4 | 4 | 4 | 4 | 4 |
| Number of Drivers | 0 | 0 | 0 | 0 | 0 |
关键差异点
- Four differential receivers in one package (对比 MC1489NG4)
- Direct documented 16-SOIC replacement path (对比 MC3486DR)
- Support for both RS-422 and RS-423 (对比 MC3487DE4)
- Defined maximum receive delay (对比 MC3486D)
设计说明
Do not treat RS-422 and RS-423 as interchangeable cable arrangements without checking the complete interface. The MC3486DG4 supports both signaling standards, but input thresholds, common-mode limits, termination, cable topology, and timing must satisfy the standard used by the connected equipment. Review the manufacturer input-output table and recommended interface circuit before fixing termination values or connector wiring.
Keep each differential input pair routed with continuous impedance and minimize the area between the two conductors. Route the pairs away from noisy switching nodes and maintain a stable reference plane beneath the interface. Place protection and termination components close to the connector when transient exposure is possible, while observing the receive-delay and signal-integrity margins required by the connected equipment.
Use the stated 35 ns maximum receive delay as one input to the system timing budget. Include connector, cable, protection-device, and receiver tolerances when calculating setup and hold time. The three-state outputs require a deliberate enable strategy: inactive receivers should remain in a defined state so bus contention or unintended leakage cannot affect connected logic.
Operate the receiver from a supply within the specified 4.75 V to 5.25 V range and follow the manufacturer decoupling recommendations. Keep the supply return path short and use a quiet return for the interface section, especially when nearby circuitry contains switching converters. Confirm that 5 V rail tolerance, startup behavior, and noise do not move the actual supply outside the receiver limits.
合规信息
The component is a commercial-temperature interface IC, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was established for this exact suffix. Compliance should be confirmed with the manufacturer or current environmental documentation.