Texas Instruments

MC3486DG4 - Quad RS-422/423 Receiver | Texas Instruments

MPN: MC3486DG4 ✓ פעיל
4.75 V to 5.25 V Vdss 16-pin SOIC, 3.90 mm width Package
כמות הזמנה מינימלית: 1 |

MC3486DG4 סקירה

Texas Instruments MC3486DG4 is a monolithic quadruple differential line receiver with four independent receiver channels, a 4.75 V to 5.25 V supply range, and a 16-pin SOIC package. It supports RS-422 and RS-423 signaling and is designed to meet ANSI TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 requirements.

A differential line receiver is an interface IC that converts a balanced differential signal arriving over a cable into a logic-level output for a digital system. The MC3486 belongs to the receiver category within the broader line-driver and transceiver hierarchy. Its four independent channels allow one device to terminate and decode four differential inputs, reducing component count in multi-channel data acquisition, industrial control, and communications equipment.

The principal features include four receiver channels, three-state outputs, TTL-compatible signaling, and operation from a nominal 5 V supply. The listed maximum receive delay is 35 ns, making the device suitable for systems that require rapid recovery of differential data from balanced lines. Its commercial temperature grade extends from 0 °C to 70 °C, while the 16-SOIC package supports conventional surface-mount PCB assembly.

Each receiver channel uses differential input signaling to reject common-mode voltage present on cabling and grounding environments. Three-state outputs permit the output pins to enter a high-impedance state when the system needs to share a data bus or isolate a receiver. The MC3486 therefore combines standard RS-422 and RS-423 reception with bus-oriented output control rather than functioning as a simple single-ended logic receiver.

Typical applications include industrial serial interfaces, test and measurement systems, data acquisition equipment, and legacy computer peripherals that communicate over balanced differential lines. Four channels make the device especially useful where multiple cable-connected sensors, controllers, or peripheral boards must feed a common digital processor. The 5 V operating range also allows the receiver to operate alongside conventional TTL and CMOS interface logic when appropriate voltage compatibility is maintained.

Designers should verify receiver enable and output-state timing against the system clock, preserve adequate differential signal margin at the cable interface, and account for connector and cable characteristics. The 35 ns maximum receive delay is a useful timing boundary when calculating setup-and-hold margins or supporting legacy peripheral clocking. Decoupling should follow the connection recommendations in the manufacturer datasheet.

This product page combines the device architecture, interface standards, timing information, verified drop-in candidates, package considerations, and practical application guidance. It also distinguishes confirmed replacement options from parts that require additional qualification, helping engineers narrow a design without confusing protocol compatibility with complete production suitability.

חלופות תחליף ישיר עבור MC3486DG4 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם MC3486DG4 (אותו גורם צורה וטביעת רגל) — שונים ב Operating Temperature Range, Output Type, Package.

Texas Instruments
Operating Temperature Range: 0°C to 70°C
Output Type: TTL-compatible 3-state outputs
Package: 16-pin SOIC
השווה עם MC3486DG4 →
Texas Instruments
Operating Temperature Range: 0°C to 70°C
Output Type: TTL-compatible 3-state outputs
Package: 16-pin SOIC
השווה עם MC3486DG4 →

MC3486DR

✅ Drop-In
Texas Instruments
📦 16-SOIC
Quadruple differential line receiver · 4 independent differential receivers · 5 V single supply · TTL-compatible 3-state outputs · Differential · ANSI TIA/EIA-422-B and TIA/EIA-423-B; ITU V.10 and V.11 · 3-state high-impedance output control · Fast transition times; exact value not provided

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

MC3486D

✅ Drop-In
Texas Instruments
📦 16-SOIC
Quadruple differential line receiver · 4 independent differential receivers · 5 V single supply · TTL-compatible 3-state outputs · Differential · ANSI TIA/EIA-422-B and TIA/EIA-423-B; ITU V.10 and V.11 · 3-state high-impedance output control · Fast transition times; exact value not provided

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

DS3486M

✅ Drop-In
📦 16-SOIC
Uses the same 4-channel receiver architecture and 16-SOIC pin arrangement; the documented functional difference relative to MC3486DG4 is 0.

📋 חלופה להתייחסות (לא בקטלוג)

DS3486MX

✅ Drop-In
📦 16-SOIC
Maintains the 4-channel differential receiver and 16-SOIC footprint; the cross-reference identifies no functional difference requiring a board change.

📋 חלופה להתייחסות (לא בקטלוג)

MC3486DG4 מפרטים

Receiver Type Quadruple differential line receiver
Number of Receivers 4
Supply Voltage Range 4.75 V to 5.25 V
Nominal Supply Voltage 5 V
Supported Protocols RS-422 and RS-423
ANSI Standard TIA/EIA-422-B and TIA/EIA-423-B
ITU Recommendations V.10 and V.11
Maximum Receive Delay 35 ns
סוג פלט 3-state, TTL-compatible
מארז 16-pin SOIC, 3.90 mm width
סוג הרכבה Surface mount
טווח טמפרטורת פעולה 0 °C to 70 °C
Packaging Tube

מדריך תצורת פינים של MC3486DG4 16-pin soic, 3.90 mm width

תצורת פינים עבור MC3486DG4 (מארזת 16-pin soic, 3.90 mm width). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 16-pin soic, 3.90 mm width עבור MC3486DG4

אין נתוני פריסת פינים מפורטים עבור MC3486DG4.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

MC3486DG4 מתאים עבור 6 יישוםs: Industrial Differential Data Acquisition, Test and Measurement Instrumentation, Legacy Peripheral Communications, Multi-Channel Sensor Interface, Process Control Communication Interfaces, Communication Backplane and Bus Isolation.

🏭

Industrial Differential Data Acquisition

The MC3486DG4 fits acquisition systems that must convert four balanced cable connections into digital logic signals for a controller or processor. Its four independent differential receiver channels reduce the number of separate receiver packages, while the 4.75 V to 5.25 V supply range supports conventional 5 V interface electronics. The receiver architecture targets ANSI TIA/EIA-422-B and TIA/EIA-423-B signaling, including ITU V.10 and V.11 recommendations. Because the maximum receive delay is 35 ns, timing analysis should include the complete input path rather than relying only on nominal propagation delay. Cable termination, common-mode conditions, and protection devices must be selected for the installation environment.

🔧

Test and Measurement Instrumentation

Instrumentation with several remote probes or fixture modules can use the MC3486DG4 to receive four balanced signals through a shared interface IC. The device converts differential RS-422 or RS-423 inputs into TTL-compatible outputs, allowing a measurement controller to read multiple channels through a defined interface standard. Its 35 ns maximum receive delay provides a concrete timing limit for synchronizing returned data with acquisition logic. Three-state outputs add flexibility when multiple interface sections must be isolated or share a bus. The 0 °C to 70 °C commercial temperature range suits controlled laboratory and production-test environments where full automotive temperature coverage is unnecessary.

🖥️

Legacy Peripheral Communications

The MC3486DG4 is appropriate for legacy computer peripherals and industrial controllers that use balanced differential communications instead of single-ended logic. Four receiver sections can decode status, command acknowledgment, data, and control lines from one 16-SOIC package. Compatibility with TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 makes it useful when the equipment interface is based on established balanced-line recommendations. The TTL-compatible outputs can interface with suitable 5 V digital logic, but designers must verify input thresholds, enable polarity, and timing in the connected legacy system. Cable routing, grounding, and termination remain essential to reliable reception.

🧩

Multi-Channel Sensor Interface

A sensor interface requiring several differential readings can place the MC3486DG4 between remote sensor lines and a digital acquisition controller. Four balanced inputs reduce package count compared with four single-channel receivers, while differential reception helps reject common-mode voltage present in industrial wiring. The nominal 5 V operation and TTL-compatible outputs align with many legacy control boards, while the 35 ns receive-delay ceiling helps define setup and hold margins. This use requires the engineer to verify that sensor signal amplitudes, common-mode limits, and bandwidth remain within the receiver electrical characteristics. Protection, termination, and isolation should also be evaluated for cable-connected sensors.

🏭

Process Control Communication Interfaces

Process-control equipment often distributes data between controllers, remote I/O, and operator panels over balanced wiring. The MC3486DG4 can receive four differential signals simultaneously, providing a compact interface between those remote nodes and a 5 V control processor. Its support for both RS-422 and RS-423 is useful where equipment uses the two related standards, while three-state outputs can assist with controlled bus isolation. The commercial temperature grade of 0 °C to 70 °C fits ordinary indoor control cabinets. System designers should account for the stated 35 ns receive delay, enable timing, cable characteristics, and any grounding or surge-protection requirements in the installation environment.

🌐

Communication Backplane and Bus Isolation

The MC3486DG4 can serve backplane systems that need several differential inputs with controllable output states. Its three-state outputs permit a receiver to be disconnected electrically when it is not selected, which is valuable when several interface sections share routing or when a system requires controlled isolation during reset. Four receiver channels and a 16-SOIC package provide moderate board-area savings over discrete implementations. The receiver supports ANSI TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 signaling, but the complete backplane must preserve the required differential impedance, termination, and signal integrity. Timing around enable and output-disable transitions should be checked at the system level.

What is the MC3486DG4 and what does it do?
The MC3486DG4 is a Texas Instruments monolithic quadruple differential line receiver with four independent channels and three-state outputs. It converts balanced RS-422 or RS-423 differential inputs into TTL-compatible logic signals. According to the manufacturer product page, the MC3486 meets ANSI TIA/EIA-422-B and TIA/EIA-423-B requirements as well as ITU V.10 and V.11 recommendations, making it suitable for multi-channel balanced data interfaces.
What is the operating voltage of MC3486DG4?
The MC3486DG4 operates from 4.75 V to 5.25 V, corresponding to a nominal 5 V supply. This supply range is identified in the manufacturer datasheet listing and device specifications. The device is intended for systems using conventional 5 V interface logic, and its 5.25 V maximum supply rating should be observed during power-supply design and transient testing.
What package does the MC3486DG4 use?
The MC3486DG4 is packaged in a 16-pin SOIC with an indicated body width of 3.90 mm. It is a surface-mount component, and the component listing identifies tube packaging for this ordering variant. Use the manufacturer pin-description table when assigning PCB tracks, and confirm the exposed dimensions and land pattern against the latest Texas Instruments datasheet before releasing artwork.
What is the maximum receive delay of MC3486DG4?
The MC3486DG4 has a maximum receive delay of 35 ns. According to the manufacturer device information, this timing value is available for the commercial-grade component. Treat 35 ns as the latest allowable receive response time when calculating interface timing margins, particularly in systems that also include external cables, connectors, logic, or downstream clock-domain-crossing circuitry.
Where can I download the MC3486DG4 datasheet PDF?
The official MC3486 documentation is available through the Texas Instruments product page at https://www.ti.com/product/MC3486. The MC3486DG4 is a temperature and ordering variant of that family, so use the ordering-information and pin-description sections to confirm its exact suffix characteristics. The manufacturer datasheet should remain the controlling document for wiring, timing, electrical limits, and revision-specific details.
Where can I find the MC3486DG4 pinout?
The MC3486DG4 pin assignments are defined in the pin-description table on the Texas Instruments MC3486 product documentation page at https://www.ti.com/product/MC3486. Because the package is a 16-pin SOIC, verify every differential input, enable-control connection, ground, and supply pin against that table before laying out the board. Do not infer receiver-channel orientation from neighboring pins.
What is the best drop-in replacement for MC3486DG4?
MC3486DR is the clearest documented drop-in candidate for MC3486DG4 because it uses the same 16-pin SOIC footprint, retains the four-channel receiver function, and is identified as a complete replacement. MC3486D, DS3486M, and DS3486MX are additional related candidates. Before production substitution, verify suffix-specific temperature, supply, timing, enable, and output behavior against the manufacturer datasheet.
Can MC3486DR replace MC3486DG4 without changing the PCB?
Yes, MC3486DR can replace MC3486DG4 without a PCB footprint change because both use the 16-pin SOIC package and are identified as pin- and package-compatible. The documented comparison states that the replacement does not require modification of the existing board. A formal engineering change should still verify temperature grade, propagation timing, supply limits, and three-state enable behavior for the exact replacement lot.
MC3486DG4 vs MC3486DR: which receiver should I choose?
Choose MC3486DR when its documented electrical characteristics match the production requirements and the sourcing plan favors a direct 16-SOIC replacement. MC3486DG4 remains the specified commercial-grade ordering variant with a stated 0 °C to 70 °C temperature range. Both devices provide the same four-channel differential-receiver architecture; the decisive checks are suffix-specific timing, temperature, enable behavior, and lifecycle continuity.
Is MC3486DG4 suitable for RS-423 and RS-422 interfaces?
The MC3486DG4 is suitable for both RS-422 and RS-423 differential interfaces. The manufacturer states that the MC3486 meets ANSI TIA/EIA-422-B and TIA/EIA-423-B requirements and ITU V.10 and V.11 recommendations. Its four independent differential inputs and three-state outputs support balanced communications systems, although cable length, topology, termination, and signal-rate margins must be validated for the complete channel.
When should I choose MC3486DG4 instead of a single-channel receiver?
Choose MC3486DG4 when the system must receive four independent balanced signals and can use a common 4.75 V to 5.25 V supply. Four integrated receiver channels can reduce board area and component count compared with four separate receiver packages. Select a single-channel device instead when the design has only one differential input, requires a different supply range, or needs channel-specific packages or electrical thresholds.
Where can I request a quote and current lead time for MC3486DG4?
Use the Request a Quote form on this page to request current MC3486DG4 pricing, stock status, and lead time. The component is identified in commercial catalogs as a Texas Instruments 16-SOIC quadruple RS-422/RS-423 receiver, but current commercial availability can change. Provide the required quantity, tube packaging preference, target date, and any suffix-specific production requirements with the request.
What is the MC3486DG4 price?
Current MC3486DG4 pricing is not stated on this page because the commercial listing does not provide a qualifying quantity-break price for the exact suffix. Use the Request a Quote form on this page and specify the required quantity, packaging, and delivery location. This ensures the quote reflects current component availability rather than a potentially stale catalog figure.
Is MC3486DG4 in stock and what is its lead time?
Current MC3486DG4 stock and lead time should be requested through the Request a Quote form on this page. The device is commercially identified as an active Texas Instruments 16-SOIC receiver, but inventory can vary by package, quantity, and date. Include your production schedule and acceptable tube-packaging requirements to obtain a schedule tied to the requested order.
What are the key specifications of MC3486DG4 that engineers should know?
The MC3486DG4 integrates four differential receivers, operates from 4.75 V to 5.25 V, supports RS-422 and RS-423, and uses a 16-pin SOIC package. Its manufacturer information identifies a maximum receive delay of 35 ns, three-state TTL-compatible outputs, a commercial temperature range of 0 °C to 70 °C, and compliance with ANSI TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11.
What Texas Instruments equivalent is available for MC3486DG4?
MC3486DR is the principal Texas Instruments equivalent documented for MC3486DG4 because it provides a completely replaceable 16-pin SOIC configuration with consistent terminals and package dimensions. MC3486D, DS3486M, and DS3486MX are also identified as compatible substitutes. The final choice should follow a datasheet review for electrical limits, temperature grade, enable timing, and qualification needs.

נתוני עזר הנדסיים עבור MC3486DG4 — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose MC3486DG4 for a 5 V system requiring four independent balanced differential inputs with TTL-compatible, three-state outputs and support for RS-422 or RS-423 signaling. It is particularly suitable when commercial temperature coverage from 0 °C to 70 °C is sufficient and the interface must meet ANSI TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, or ITU V.11 requirements. MC3486DR is the preferred documented replacement candidate when its suffix-specific specifications match and sourcing continuity is more important than retaining the original ordering code. MC3486D, DS3486M, and DS3486MX are related alternatives, but their exact electrical limits and qualification details should be reviewed before production use. Choose a broader transceiver such as MC3487DE4 when the system also needs differential line drivers. If the design needs only one channel, exceeds the commercial temperature range, or requires another supply voltage, use a receiver family that better matches those requirements rather than forcing a four-channel replacement.

השוואה עם חלופות

פרמטר מוצר זה MC3486DR MC3486D DS3486M DS3486MX
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Number of Receivers 4 4 4 4 4
Number of Drivers 0 0 0 0 0

מבדילים עיקריים

  • Four differential receivers in one package (לעומתMC1489NG4)
  • Direct documented 16-SOIC replacement path (לעומתMC3486DR)
  • Support for both RS-422 and RS-423 (לעומתMC3487DE4)
  • Defined maximum receive delay (לעומתMC3486D)

הערות תכנון

Do not treat RS-422 and RS-423 as interchangeable cable arrangements without checking the complete interface. The MC3486DG4 supports both signaling standards, but input thresholds, common-mode limits, termination, cable topology, and timing must satisfy the standard used by the connected equipment. Review the manufacturer input-output table and recommended interface circuit before fixing termination values or connector wiring.

Keep each differential input pair routed with continuous impedance and minimize the area between the two conductors. Route the pairs away from noisy switching nodes and maintain a stable reference plane beneath the interface. Place protection and termination components close to the connector when transient exposure is possible, while observing the receive-delay and signal-integrity margins required by the connected equipment.

Use the stated 35 ns maximum receive delay as one input to the system timing budget. Include connector, cable, protection-device, and receiver tolerances when calculating setup and hold time. The three-state outputs require a deliberate enable strategy: inactive receivers should remain in a defined state so bus contention or unintended leakage cannot affect connected logic.

Operate the receiver from a supply within the specified 4.75 V to 5.25 V range and follow the manufacturer decoupling recommendations. Keep the supply return path short and use a quiet return for the interface section, especially when nearby circuitry contains switching converters. Confirm that 5 V rail tolerance, startup behavior, and noise do not move the actual supply outside the receiver limits.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The component is a commercial-temperature interface IC, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was established for this exact suffix. Compliance should be confirmed with the manufacturer or current environmental documentation.

הנתונים אומתו בתאריך: 2026-11-11 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

MC3486DG4 datasheet MC3486DG4 pinout MC3486DG4 datasheet pdf MC3486DG4 equivalent MC3486DG4 replacement MC3486DG4 vs MC3486DR MC3486DG4 16-SOIC receiver MC3486DG4 RS-422 interface MC3486DG4 RS-423 receiver MC3486DG4 4.75V 5.25V Texas Instruments MC3486DG4 MC3486DG4 price MC3486DG4 stock MC3486DG4 lead time MC3486DG4 application circuit

רכיבים ומונחים קשורים

Texas Instruments MC3486DG4 MC3486DR MC3486D DS3486M DS3486MX quadruple differential line receiver RS-422 RS-423 differential receiver line receiver interface IC transceiver three-state output TTL-compatible output TIA/EIA-422-B TIA/EIA-423-B ITU V.10 ITU V.11 16-SOIC SOIC package family surface-mount package 4.75 V to 5.25 V supply 35 ns maximum receive delay industrial data acquisition
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר