MC56F8013VFAE - 16-Bit 32MHz DSC, 16KB Flash, LQFP-32 | NXP
料号： MC56F8013VFAE ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $7.45 | $7.45 |
| 10 | $6.71 | $67.10 |
| 100 | $5.85 | $585.00 |
| 500 | $5.12 | $2,560.00 |
| 1,000 | $4.62 | $4,620.00 |
MC56F8013VFAE 概述
What is a Digital Signal Controller? A Digital Signal Controller (DSC) is a hybrid class of embedded processor that combines microcontroller (MCU) peripherals and interrupt-driven control with the deterministic numeric throughput of a digital signal processor (DSP). In the system hierarchy, a DSC sits between a general-purpose MCU (e.g., ARM Cortex-M0) and a standalone DSP (e.g., TI C6000). DSCs are widely used in motor control, power conversion, and sensor-fusion applications where both deterministic control loops and arithmetic DSP kernels are required on one chip. The 56800E core used in the 56F8013 family adds a Harvard-style memory architecture and single-cycle MAC operations typical of DSP cores.
Key features of the MC56F8013 include 16 KB Flash, 4 KB RAM, a 32 MHz 56800E core with single-cycle 16-bit multiply-accumulate, dual 6-channel PWM modules for motor drive, two 12-bit ADCs with up to 8 channels, and communication peripherals including SCI, SPI, and I2C. The 56F8013 derivative adds a CAN 2.0 A/B module versus the lower-feature 56F8011 sibling. On-chip regulators and a low-power Stop mode reduce quiescent draw for battery-connected systems.
Typical applications span BLDC/PMSM motor drives (drones, e-bikes, appliances), digital switched-mode power supplies (PFC + LLC), automotive sensor interfaces, and industrial servo loops. The 56800E instruction set is C-friendly and supported by NXP's CodeWarrior and the newer MCUXpresso toolchain plus Processor Expert graphical configuration.
Design considerations: maintain a clean analog ground island for ADC accuracy, place the 3.3 V decoupling network within 5 mm of the supply pins, and verify PWM timing closure against the application's control-loop rate. The LQFP-32 footprint allows hand-soldering and rework on prototype boards.
直接替换替代料： MC56F8013VFAE ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MC56F8013VFAE （相同外形与封装尺寸） ——差异在于 ADC, Core Architecture, Operating Temperature, PWM Modules, Package.
快速对比工具——选择替代料号进行并排对比：
MC56F8011VFAE
✅ 直接替换📋 参考替代料（不在目录中）
MC56F8014VFAE
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →MC56F8013VFAER
✅ 直接替换📋 参考替代料（不在目录中）
MC56F8037VLH
✅ 直接替换✓ 有现货
$5.1 / 个
查看数据手册 →MC56F8013VFAE 最大额定值与电气特性
| Core Architecture | 56800E 56F8xxx (16-bit DSC) |
| Core Clock Speed | 32 MHz |
| Program Memory (Flash) | 16 KB (8K x 16) |
| RAM | 4 KB |
| 电源电压 | 3.3 V |
| 封装 | 32-LQFP (7x7 mm) |
| 安装类型 | Surface Mount |
| PWM Modules | Dual 6-channel (12 PWM outputs) |
| ADC | Dual 12-bit ADC, up to 8 channels |
| Communication Peripherals | SCI, SPI, I2C, CAN 2.0 A/B |
| 工作温度 | -40C to +105C (Industrial) |
| MSL 等级 | 3 (168 hours) |
| RoHS 状态 | Compliant |
| AEC-Q100 | Qualified |
| Instruction Set | 16-bit CISC, single-cycle MAC |
| Low-Power Mode | Stop / Wait modes |
MC56F8013VFAE 引脚配置
| 引脚 1 | VDD — 3.3 V digital supply |
| 引脚 2 | VSS — Digital ground |
| 引脚 3 | GPIOA0 / PWM_A0 / TMR0 — General-purpose I/O / PWM channel A0 / Timer 0 |
| 引脚 4 | GPIOA1 / PWM_A1 / TMR1 — General-purpose I/O / PWM channel A1 / Timer 1 |
| 引脚 5 | GPIOA2 / PWM_A2 — General-purpose I/O / PWM channel A2 |
| 引脚 6 | GPIOA3 / PWM_A3 — General-purpose I/O / PWM channel A3 |
| 引脚 7 | GPIOA4 / PWM_A4 / ANA4 — General-purpose I/O / PWM A4 / ADC input ANA4 |
| 引脚 8 | GPIOA5 / PWM_A5 / ANA5 — General-purpose I/O / PWM A5 / ADC input ANA5 |
| 引脚 9 | GPIOB0 / PWM_B0 / ANA6 — General-purpose I/O / PWM B0 / ADC input ANA6 |
| 引脚 10 | GPIOB1 / PWM_B1 / ANA7 — General-purpose I/O / PWM B1 / ADC input ANA7 |
| 引脚 11 | GPIOB2 / PWM_B2 / ANA0 — General-purpose I/O / PWM B2 / ADC input ANA0 |
| 引脚 12 | GPIOB3 / PWM_B3 / ANA1 — General-purpose I/O / PWM B3 / ADC input ANA1 |
| 引脚 13 | GPIOB4 / PWM_B4 / ANA2 — General-purpose I/O / PWM B4 / ADC input ANA2 |
| 引脚 14 | GPIOB5 / PWM_B5 / ANA3 — General-purpose I/O / PWM B5 / ADC input ANA3 |
| 引脚 15 | VDDA — Analog 3.3 V supply for ADC |
| 引脚 16 | VSSA — Analog ground reference for ADC |
| 引脚 17 | CAN_TX — CAN 2.0 A/B transmit (56F8013 only) |
| 引脚 18 | CAN_RX — CAN 2.0 A/B receive (56F8013 only) |
| 引脚 19 | TXD0 / SDA — SCI0 transmit or I2C SDA |
| 引脚 20 | RXD0 / SCL — SCI0 receive or I2C SCL |
| 引脚 21 | MISO0 / SDA1 — SPI0 MISO or I2C1 SDA |
| 引脚 22 | MOSI0 / SCL1 — SPI0 MOSI or I2C1 SCL |
| 引脚 23 | SCLK0 — SPI0 clock |
| 引脚 24 | SS0 — SPI0 slave select |
| 引脚 25 | TCLK / PWM_A0 — Timer clock input or PWM A0 alt |
| 引脚 26 | RESET — Active-low reset input |
| 引脚 27 | EXTAL — External clock/crystal input |
| 引脚 28 | XTAL — External clock/crystal output |
| 引脚 29 | TMS — JTAG test mode select |
| 引脚 30 | TCK — JTAG test clock |
| 引脚 31 | TDI — JTAG test data in |
| 引脚 32 | TDO — JTAG test data out |
典型应用
MC56F8013VFAE 适用于 6 应用s: BLDC / PMSM Motor Control, Digital Switched-Mode Power Supplies (PFC + LLC), Automotive Body Electronics & Actuators, Industrial Sensor-Fusion & Servo Loops, Battery-Connected Low-Power Embedded Systems, Digital Audio & DSP Pre-Processing.
BLDC / PMSM Motor Control
The MC56F8013VFAE's dual 6-channel PWM modules (12 PWM outputs total) directly drive three-phase inverter bridges for BLDC and PMSM motors, while the dual 12-bit ADC (8 channels) samples phase currents and the DC-bus voltage for sensorless FOC. The 56800E core's single-cycle 16-bit MAC executes the Park/Clarke transforms and PI controllers within the typical 16 kHz current-loop rate. With 16 KB Flash and 4 KB RAM it fits field-oriented-control firmware for appliances, drones, e-bikes, and small industrial drives, and the on-chip CAN enables automotive and industrial networking of the motor node.
推荐
Digital Switched-Mode Power Supplies (PFC + LLC)
In digital PFC and LLC power-converter designs, the MC56F8013VFAE closes the voltage and current loops at PWM rates up to 32 MHz core clock. The dual ADCs sample input current, output voltage, and resonant-tank currents simultaneously, and the dual PWM modules generate complementary gate-drive signals with programmable dead time for the LLC half-bridge. The 16-bit 56800E MAC supports average-current-mode control and valley-skipping algorithms. AEC-Q100 qualification supports on-board chargers and industrial telecom PSUs.
推荐
Automotive Body Electronics & Actuators
The MC56F8013VFAE's AEC-Q100 qualification, integrated CAN 2.0 A/B controller, and 3.3 V operation make it a fit for body-electronics modules such as HVAC blend doors, mirror adjusters, seat-position actuators, and lighting controllers. The 32-LQFP footprint accommodates small PCBAs under tight packaging constraints, and the PWM + ADC + CAN combination handles a complete sub-system without external glue logic. The 56800E core runs end-node AUTOSAR-style software with deterministic interrupt latency for actuator control.
推荐
Industrial Sensor-Fusion & Servo Loops
Industrial servo and sensor-fusion nodes use the MC56F8013VFAE's 32 MHz 56800E core to combine PID control loops with on-chip DSP-class filtering. The dual ADCs read position encoders and load cells, while the PWM outputs drive brushed or brushless servo actuators. CAN connectivity ties the node into industrial fieldbus networks. The 16 KB Flash stores commissioning firmware and calibration tables, and 4 KB RAM handles buffer memory for ADC ping-pong acquisition.
推荐
Battery-Connected Low-Power Embedded Systems
The MC56F8013VFAE's Stop and Wait low-power modes, plus its single 3.3 V supply rail, suit battery-connected embedded systems such as portable instrumentation, e-mobility accessories, and IoT edge nodes. The 56800E core wakes from Stop on a programmable interrupt (timer, ADC, or CAN) and resumes control loops within microseconds. On-chip Flash/RAM removes external memory and reduces quiescent BOM cost. CAN/SPI/I2C enable low-power sensor and battery-management IC connectivity.
推荐
Digital Audio & DSP Pre-Processing
Although not its primary market, the MC56F8013VFAE's 56800E core can perform digital audio pre-processing tasks such as FIR/IIR filtering, dynamic-range compression, and active-noise-cancellation front-ends. The single-cycle MAC accelerates biquad cascades, and the PWM outputs can generate sigma-delta-style audio bit-streams for class-D amplifier front ends. For higher-fidelity audio DSP, designers typically migrate to the MC56F827xx family, but the 56F8013 covers cost-sensitive consumer audio accessories.
推荐
推荐产品汇总
工程参考数据： MC56F8013VFAE ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC56F8011VFAE | MC56F8014VFAE | MC56F8013VFAER |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 32-LQFP (7x7 mm) | 32-LQFP (7x7 mm) | 32-LQFP (7x7 mm) | 32-LQFP (7x7 mm) |
| Core | 56800E 16-bit DSC, 32 MHz | 56800E 16-bit DSC, 32 MHz | 56800E 16-bit DSC, 32 MHz | 56800E 16-bit DSC, 32 MHz |
| Flash | 16 KB | 12 KB | 32 KB | 16 KB |
| RAM | 4 KB | 2 KB | 8 KB | 4 KB |
| CAN Module | Yes (CAN 2.0 A/B) | No | Yes | Yes |
| PWM Channels | 12 (dual 6-ch) | 12 (dual 6-ch) | 12 (dual 6-ch) | 12 (dual 6-ch) |
| ADC | Dual 12-bit, 8 ch | Dual 12-bit, 8 ch | Dual 12-bit, 8 ch | Dual 12-bit, 8 ch |
| AEC-Q100 | Yes | Yes | Yes | Yes |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
关键差异点
- Integrated CAN 2.0 A/B module in this LQFP-32 footprint （对比 MC56F8011VFAE)
- 16 KB Flash - cost-optimized for typical motor-control firmware （对比 MC56F8014VFAE)
- 56800E DSC core with single-cycle MAC in a small LQFP-32 （对比 MC56F8037VLH)
设计说明
Place a 1 uF ceramic decoupling capacitor on each VDD/VSS pair within 5 mm of the package pin, plus a single 10 uF bulk capacitor near the analog supply VDDA. The 56800E core draws brief high-current pulses on each instruction fetch; inadequate decoupling causes CodeWarrior/MCUXpresso emulator debug failures and erratic Flash programming. The VDDA rail powering the dual 12-bit ADC should be filtered with a ferrite bead and 100 nF cap to keep digital switching noise out of ADC readings.
Route the analog ground VSSA as a star back to the regulator ground, isolated from the digital VSS plane until they meet at the chip's exposed pad. Use a single solid VSS pour under the LQFP-32 footprint to maximize thermal dissipation for the 32 MHz internal core. Keep ADC traces (ANA0..ANA7) short and symmetric to minimize channel-to-channel skew on the dual ADC. Route the JTAG signals (TMS/TCK/TDI/TDO) at least 3 mm away from PWM switching traces to avoid emulator debug noise pickup.
Do not assume the 56F8013 and 56F8011 are interchangeable - the 56F8013 includes the CAN 2.0 A/B module that the 56F8011 lacks, and CAN register definitions differ. Flash programming must use NXP's CodeWarrior or MCUXpresso toolchain; third-party tools cannot access the on-chip Flash controller. The internal regulator requires the VDDA pin to be present and within spec even if the ADC is unused - leaving VDDA floating causes indeterminate behavior. Always configure the PWM fault pins before enabling the PWM counter in motor-control firmware.
合规信息
RoHS and REACH compliant per NXP product page. AEC-Q100 qualified for automotive use. Halogen-free and lead-free packaging confirmed. Conflict-minerals statement available from NXP.