MC9S08JE128VLH - 8-bit S08 USB MCU, 128KB Flash, 48MHz | NXP
料号： MC9S08JE128VLH ⚠ 最后一次采购| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $8.59 | $8.59 |
| 10 | $7.73 | $77.30 |
| 100 | $6.87 | $687.00 |
| 500 | $6.01 | $3,005.00 |
| 1,000 | $5.15 | $5,150.00 |
MC9S08JE128VLH 概述
A microcontroller (MCU) is an integrated circuit that combines a processor, RAM, non-volatile program memory, and a peripheral set into a single chip. The 8-bit microcontroller category sits below 16-bit and 32-bit MCUs in computational throughput, but typically offers lower cost, lower power consumption, and simpler programming. Within NXP's portfolio, S08 microcontrollers occupy the low-power, cost-sensitive tier, above which sit the S12 (16-bit), Kinetis E (Cortex-M0+/M4), and Kinetis K (Cortex-M4) families. The MC9S08JE128VLH sits inside the LQFP-64 package family (LQFP family -> QFP family -> surface-mount plastic IC package), placing it in the mainstream SMD microcontroller footprint class.
Key features of the MC9S08JE128VLH include integrated USB 2.0 connectivity, a high-resolution analog-to-digital converter (ADC), a digital-to-analog converter (DAC), multiple serial peripherals (SCI, SPI, I2C), a rich timer/PWM set, and an internal low-power oscillator. The combination of ADC, DAC, and USB on the same die eliminates external analog components and a separate USB transceiver, reducing both board space and BOM cost in measurement and consumer applications.
From an application perspective, the MC9S08JE128VLH targets HVAC building control systems, PC peripherals, lighting control systems, industrial networking products, and portable medical devices, according to the Freescale/NXP product brief. These segments benefit from the on-chip ADC resolution, USB device/host/OTG support, and the low-power modes that the S08JE core offers for battery-powered instruments. NXP's product page classifies this part as End-of-Life (EOL) with a published Discontinuance and Replacement Product Change Notice, so designers planning new designs should evaluate replacement parts listed in the alternatives array and the NXP PCN.
Designers should be aware of the part's EOL status when planning new designs. The recommended approach is to verify the active PCN and replacement MPN list on NXP's website before committing to a new design. Existing designs in production should secure safety stock and qualify a same-package drop-in from the alternatives array below to mitigate future supply risk.
直接替换替代料： MC9S08JE128VLH ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MC9S08JE128VLH （相同外形与封装尺寸） ——差异在于 Package.
快速对比工具——选择替代料号进行并排对比：
MC9S08JE64VLH
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →MC9S08JE128VLHR
✅ 直接替换📋 参考替代料（不在目录中）
MC9S08JE128VLH 最大额定值与电气特性
| Core | HCS08 / S08 (8-bit) |
| Processor Series | S08JE |
| 数据总线宽度 | 8 bit |
| 最大时钟频率 | 48 MHz |
| Program Memory Size | 128 KB (128K x 8) FLASH |
| 封装 | 64-LQFP (10x10 mm) |
| 安装类型 | Surface Mount |
| 电源电压 | 2.5 V / 3.3 V |
| USB Interface | USB 2.0 (integrated) |
| ADC | High-resolution on-chip ADC |
| DAC | On-chip DAC |
| Serial Peripherals | SCI (UART), SPI, I2C |
| RoHS 状态 | Details available (contact DigiKey) |
| Lifecycle | End of Life (Discontinuance PCN published on NXP) |
MC9S08JE128VLH 64-lqfp (10x10 mm) 引脚配置指南
MC9S08JE128VLH（64-lqfp (10x10 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MC9S08JE128VLH.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC9S08JE128VLH 适用于 6 应用s: HVAC Building Control Systems, USB PC Peripherals, Industrial Lighting Control, Industrial Networking Products, Portable Medical Devices, Battery-Powered Measurement Instruments.
HVAC Building Control Systems
The MC9S08JE128VLH fits HVAC building control because the S08JE core's ultra-low-power modes keep wall and rooftop controllers efficient, the on-chip high-resolution ADC handles thermistor and pressure-sensor readout without external signal conditioning, and the integrated DAC drives analog actuator setpoints. Per NXP's product brief, HVAC is a primary target segment for this device. Designers place the JE128VLH between the sensor network and the user interface, using the SCI (UART) for BACnet or Modbus trunks while USB provides field-service commissioning ports - a topology that exploits the part's USB 2.0 device stack without external transceivers.
推荐
USB PC Peripherals
The MC9S08JE128VLH is a strong fit for USB PC peripherals (HID, CDC, vendor-class devices) because USB 2.0 full-speed is integrated on the die, eliminating the external USB transceiver and reducing BOM by 2-3 ICs. The 128 KB FLASH holds a full USB stack plus application firmware, and the S08JE core runs at 48 MHz - the bus-clock rate required for accurate USB full-speed framing. Compared with general-purpose MCUs that require an external USB PHY, the JE128VLH offers a single-chip USB device solution at 8-bit cost points, which is why NXP highlights PC peripherals as a primary application.
推荐
Industrial Lighting Control
The MC9S08JE128VLH fits industrial lighting control because the S08JE core's PWM/timer set drives LED drivers and TRIAC dimming stages with microsecond precision, while the 12-bit-class ADC reads ambient-light and occupancy sensors directly. USB connectivity simplifies factory test and firmware update via a standard cable, and the ultra-low-power modes (HALT, STOP) cut idle lighting-controller standby below 1 mA. Per NXP's product brief, lighting control systems are an explicit target segment for the S08JE family.
推荐
Industrial Networking Products
The MC9S08JE128VLH fits industrial networking products - bridges, gateways, sensor nodes - because the S08JE core integrates SCI (UART), SPI, and I2C, enabling RS-485, RS-232, and I2C sensor networks from a single chip. The 128 KB FLASH holds a Modbus or proprietary networking stack, and the integrated USB enables local configuration plus firmware update. Designers appreciate the 48 MHz core for deterministic serial-frame timing, and the wide supply range (2.5 V / 3.3 V per distributor listings) lets the part operate directly from industrial 24 V pre-regulated rails.
推荐
Portable Medical Devices
The MC9S08JE128VLH fits portable medical devices because the high-resolution on-chip ADC enables accurate SpO2, temperature, or pressure measurement without external analog front-ends, and the integrated DAC drives reference voltages or analog outputs. The S08JE ultra-low-power modes extend battery life on handheld instruments, while USB 2.0 enables patient-data transfer and battery charging. NXP lists portable medical devices as an explicit target segment. Designers must still validate the complete system's IEC 60601 compliance - the MCU alone does not certify the device.
推荐
Battery-Powered Measurement Instruments
The MC9S08JE128VLH fits battery-powered measurement instruments where the S08JE ultra-low-power operation extends run-time and the high-resolution ADC enables accurate readings. The 48 MHz core executes DSP-style signal-processing routines (FIR filters, RMS calculation) within tight timing budgets, while integrated USB enables charging plus data sync. Per NXP's product brief, ultra-low-power operation is a defining trait of the JE128/64 family, making the part well-suited to handheld digital multimeters, dataloggers, and environmental monitors.
推荐
推荐产品汇总
工程参考数据： MC9S08JE128VLH ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC9S08JE64VLH | MC9S08JE128VLHR | MC9S08JM60CLD | MC9S08MM128VLH |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | LQFP (different footprint, pin-count differs) | 64-LQFP (same family footprint) |
| Core | S08 (8-bit) | S08 (8-bit) | S08 (8-bit) | S08 (8-bit) | S08 (8-bit) |
| Maximum Clock Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Program FLASH | 128 KB | 64 KB (-50%) | 128 KB | 60 KB | 128 KB |
| USB Interface | USB 2.0 integrated | USB 2.0 integrated | USB 2.0 integrated | USB 2.0 integrated (with host/OTG) | No native USB |
| On-chip ADC | Yes (high-resolution) | Yes (high-resolution) | Yes (high-resolution) | Yes | Yes |
关键差异点
- USB 2.0 plus on-chip DAC for measurement-class peripherals （对比 MC9S08MM128VLH)
- Twice the program memory of the JE64 sibling （对比 MC9S08JE64VLH)
- Single-tray 64-LQFP (10x10) footprint aligns with standard S08JE layout （对比 MC9S08JM60CLD)
设计说明
The MC9S08JE128VLH is on NXP's published Discontinuance and Replacement PCN list. Before committing a new design to this MPN, open the NXP product page's PCN section and read the qualified replacement. Existing designs should secure safety stock and qualify a same-package drop-in alternative from the alternatives array below. Continuing to design in an EOL part creates supply risk that may force a redesign later.
Take advantage of the S08JE family's ultra-low-power modes (WAIT, STOP3) for battery-powered designs. Stop currents in the single-digit microamp range are typical per NXP datasheets. Wakeup can be triggered by ADC threshold, low-voltage detect, RTI, or external IRQ, allowing average system current below 100 uA in HVAC sensor-node duty cycles.
Decouple VDD/VSS pairs with 100 nF X7R caps placed within 3 mm of each supply pin, plus a single bulk 4.7 uF tantalum or ceramic near the regulator. The USB D+/D- traces should be routed as a 90-ohm differential pair with length matching within 2 mm, and the internal 3.3 V USB regulator's bypass cap must be placed within 5 mm of the USB VREG pin.
合规信息
RoHS and REACH status not stated explicitly in verified distributor listings; consult DigiKey product page for full compliance detail. AEC-Q100 not applicable - this is a general-purpose 8-bit MCU, not an automotive-qualified part. Lead-free confirmed via standard NXP LQFP package family.