MCP601T-I/OT - 2.8MHz RRO CMOS Op Amp | Microchip Technology
料号: MCP601T-I/OT ✓ 量产中MCP601T-I/OT 概述
An operational amplifier, commonly called an op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The MCP601 belongs to the CMOS operational-amplifier hierarchy, where low power consumption and low input bias current support battery-powered and high-impedance signal chains. Its rail-to-rail output stage allows the output voltage to approach the supply rails, improving useful signal range in low-voltage systems.
Three headline characteristics define the MCP601T-I/OT: its 2.8 MHz gain-bandwidth product supports higher-frequency closed-loop operation than very-low-bandwidth amplifiers, its 230 uA typical operating current suits low-power designs, and its offset voltage of less than 2 mV limits systematic input-referred error. The device uses Microchip advanced CMOS technology and provides rail-to-rail output swing, low bias current, high open-loop gain, and high speed.
Because the gain-bandwidth product is 2.8 MHz, the amplifier is most appropriate for low-to-moderate frequency precision signal paths rather than high-speed video or RF tasks. Closed-loop bandwidth depends on the selected noise-gain topology; for example, a non-inverting amplifier configured for 10-times gain has a much lower usable bandwidth than a unity-gain configuration. Input offset, bias current, output swing, supply voltage, and stability determine practical precision.
Typical uses include low-power sensor conditioning, portable instrumentation, audio preamplification, active filtering, and general-purpose analog signal processing. The single 2.7 V to 6.0 V supply range makes the device suitable for systems using 3.3 V or 5 V rails. Its low operating current is beneficial in battery-operated equipment where every milliampere affects operating time.
When laying out the PCB, keep the op-amp input pins away from switching nodes, high-current traces, and digital clock lines. Place input and feedback components close to their associated pins, use a solid ground reference, and follow the stability and decoupling recommendations in the manufacturer documentation. The unused supply pin must be connected to the appropriate supply or ground potential rather than left floating.
This product page combines the manufacturer specifications with package, application, replacement, and design guidance. It also distinguishes the industrial-temperature MCP601T-I/OT from other mechanically related variants, helping engineers identify a valid board-level replacement without confusing package compatibility with functional equivalence.
直接替换替代料: MCP601T-I/OT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MCP601T-E/OT
✅ 直接替换📋 参考替代料(不在目录中)
MCP601T-I/OT 最大额定值与电气特性
| Device Type | Single operational amplifier |
| Product Classification | General-purpose amplifier |
| Technology | CMOS |
| Supply Configuration | Single supply |
| Supply Voltage Range | 2.7 V to 6.0 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Typical Input Offset Voltage | Less than 2 mV |
| Output Swing | Rail-to-rail |
| Number of Circuits | 1 circuit |
| 封装 | SOT-23-5 |
| 安装类型 | Surface mount |
| Packaging | Tape and reel |
| AEC-Q100 Qualification | Not applicable |
MCP601T-I/OT sot-23-5 引脚配置指南
MCP601T-I/OT(sot-23-5 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: MCP601T-I/OT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MCP601T-I/OT 适用于 6 应用s: Low-Power Sensor Signal Conditioning, Portable Medical Monitoring, Audio Preamplification, Active Filtering and Control, Portable Test and Measurement, IoT Sensor Interface.
Low-Power Sensor Signal Conditioning
The MCP601T-I/OT is well suited to conditioning signals from high-impedance sensors because its CMOS architecture provides low bias current and its typical operating current is only 230 uA. Place it in a non-inverting or differential conditioning stage operating from a 2.7 V to 6.0 V rail, with the sensor return tied to the circuit reference. The 2.8 MHz gain-bandwidth product permits useful closed-loop bandwidth beyond very-low-frequency conditions, while less than 2 mV typical offset limits input-referred error. A rail-to-rail output also increases usable signal swing near the supply limit.
推荐
Portable Medical Monitoring
The MCP601T-I/OT can form the input amplifier of a compact, battery-operated monitoring module when the design requires low power and modest signal bandwidth. Its 230 uA typical operating current supports longer operating intervals, while the single 2.7 V to 6.0 V supply range accommodates portable 3.3 V architectures. Use a low-noise reference and properly grounded sensor interface to preserve the benefit of less than 2 mV typical input offset. The 2.8 MHz gain-bandwidth product is appropriate for physiological signals and slow sensor outputs rather than high-bandwidth diagnostic front ends.
推荐
Audio Preamplification
The MCP601T-I/OT can amplify microphone or line-level signals in a compact audio preamplifier when the operating bandwidth is modest. Its 2.8 MHz gain-bandwidth product is much greater than the bandwidth of most audio-band signals, and its rail-to-rail output increases available swing from a 3.3 V or 5 V supply. Typical operating current of 230 uA helps when the audio circuit operates continuously from a limited power budget. Keep the input return path short, provide stable feedback compensation, and avoid routing the microphone input beside switching regulators or digital timing signals.
推荐
Active Filtering and Control
The MCP601T-I/OT is appropriate for first-order or low-order active filters used in sensor and control systems. Its 2.8 MHz gain-bandwidth product leaves bandwidth margin above audio-band and low-frequency process-control signals, while the rail-to-rail output can feed another stage without immediately saturating near the supply rail. Select passive-component tolerances that match the required filter accuracy because amplifier offset and bias current also influence low-frequency behavior. Verify closed-loop stability for each noninverting or inverting gain setting before increasing signal bandwidth.
推荐
Portable Test and Measurement
The MCP601T-I/OT can serve as a general-purpose amplifier in a handheld meter, programmable sensor interface, or low-speed data-acquisition front end. Its 2.8 MHz gain-bandwidth product supports measurement signals beyond DC, and the less-than-2-mV typical offset is useful when resolving small inputs. The 230 uA typical operating current helps constrain battery demand, while operation from a single 2.7 V to 6.0 V supply simplifies portable power design. Place the amplifier near the input connector, maintain a low-impedance reference, and isolate analog traces from switching-converter paths.
推荐
IoT Sensor Interface
The MCP601T-I/OT is useful between an IoT sensor and a low-voltage controller when the sensor output requires buffering or gain. Its low bias current reduces loading on high-impedance sensing elements, and the 2.8 MHz gain-bandwidth product is more than sufficient for common temperature, light, pressure, and occupancy sensors. A 3.3 V supply keeps the operating range aligned with many wireless systems, while rail-to-rail output improves utilization of the controller's analog input range. Use short traces, a continuous ground reference, and filtering near the sensor connector to minimize environmental noise pickup.
推荐
推荐产品汇总
工程参考数据: MCP601T-I/OT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MCP601T-E/OT |
|---|---|---|
| Manufacturer | Microchip Technology | Microchip Technology |
| Package | SOT-23-5 | SOT-23-5 |
| Device Type | Single CMOS operational amplifier | Single general-purpose amplifier |
| Packaging | Tape and reel | Tape and reel |
关键差异点
- Low-power single-supply operation (对比 MCP601T-E/OT)
- Industrial-grade ordering option (对比 MCP601T-E/OT)
- Compact five-pin analog interface (对比 MCP601T-E/OT)
设计说明
Place the MCP601T-I/OT close to the signal source and place feedback components directly between the input and output pins. Keep the ground return beneath the device continuous, avoid split-plane transitions beneath the amplifier, and place supply bypass capacitance at the power pin. Sensitive input traces should remain short and should not run parallel to switching-node, inductor, or high-current return paths.
Choose the closed-loop gain with the 2.8 MHz gain-bandwidth product in mind. Higher noise gain reduces usable bandwidth and can change stability requirements, particularly when driving capacitive loads. If the amplifier drives a cable, ADC input, or other capacitive network, add an isolation resistor close to the output and verify stability experimentally. Do not assume that the rail-to-rail output stage can drive arbitrary capacitive loads without added damping.
Decouple the 2.7 V to 6.0 V supply locally and account for the amplifier's 230 uA typical operating current plus signal-dependent current. Use the manufacturer's recommended bypass capacitance and connection layout, and keep analog and switching regulators physically separated where possible. The less-than-2-mV typical input offset improves signal accuracy, but that performance is retained only when the input reference and return paths are quiet and properly conditioned.
Do not confuse package compatibility with complete substitute qualification. The MCP601T-E/OT shares the SOT-23-5 format and MCP601 family identity, but the ordering-grade temperature difference must be checked against the design's worst-case ambient conditions. Before fitting any alternative, verify input and supply pin positions, common-mode range, output swing, offset, bias current, bandwidth, operating current, stability, and exposed-pad or thermal requirements.
合规信息
Material-compliance declarations are not stated in the manufacturer product information for this ordering code. AEC-Q100 is not applicable to this general-purpose amplifier.