Microchip Technology

MCP6021-E/ST - 10MHz RRO Op Amp | Microchip Technology

料号: MCP6021-E/ST ✓ 量产中
2.5 V to 5.5 V Vdss 1.0 mA Id 8-pin TSSOP, 0.173 inch (4.40 mm) wide Package
最小起订量: 1 |

MCP6021-E/ST 概述

The Microchip Technology MCP6021-E/ST is a single, rail-to-rail input and output CMOS operational amplifier with a 10 MHz gain-bandwidth product, a typical operating current of 1.0 mA, and an input offset voltage below 0.5 mV. It is packaged in an 8-pin TSSOP and operates from a 2.5 V to 5.5 V power supply. The MCP6021 combines low bias current, high open-loop gain, and rail-to-rail output swing in a general-purpose amplifier suitable for portable instrumentation and low-voltage signal-conditioning systems.

An operational amplifier is an active analog component that amplifies the difference between voltages applied to its inverting and non-inverting inputs. The MCP6021 belongs to the hierarchy of operational amplifier, voltage-feedback amplifier, analog signal IC, and semiconductor. Its rail-to-rail input stage accepts signals close to either supply rail, while its rail-to-rail output stage provides a wide output swing. This makes it useful when the signal range leaves little headroom above or below the supply voltages.

Principal features include a 10 MHz gain-bandwidth product, low typical operating current of 1.0 mA, an offset voltage below 0.5 mV, and low input bias current. The 2.5 V minimum supply voltage supports 3.3 V and 5 V systems. The -E suffix identifies the extended-temperature product grade, while the /ST package code denotes the 8-pin TSSOP configuration. The wide operating range makes the device applicable to industrial control, sensor interfaces, battery-powered equipment, and audio input conditioning.

The MCP6021 uses advanced CMOS technology and a voltage-feedback architecture. At unity gain, its approximately 10 MHz bandwidth provides useful response for low-frequency measurement, current sensing, and active filtering. A single amplifier can be configured as a non-inverting stage, inverting stage, voltage follower, comparator-style interface, or transimpedance front end. The low 1.0 mA operating current reduces supply demand in portable systems, although actual consumption varies with supply voltage, output swing, frequency, and load.

Typical applications include low-voltage sensor conditioning, current sensing, active filters, audio microphone preamplification, data acquisition, and general-purpose analog signal chains. For a current-sensing application, the amplifier can amplify the small voltage generated across a shunt resistor while its rail-to-rail inputs accept signals near the lower supply rail. For active filtering, the 10 MHz bandwidth leaves margin above the filter corner frequency while limiting the required supply current.

Design with the 2.5 V to 5.5 V supply range and input common-mode limits in mind. Keep input and feedback traces short, place decoupling capacitors close to the supply pins, and avoid routing sensitive input signals beside digital switching nodes. Follow the manufacturer datasheet pin-description table when assigning PCB tracks, and confirm the extended-temperature limits and automotive-grade requirements for the exact ordering code before production release.

直接替换替代料: MCP6021-E/ST ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

MCP6021T-E/ST

✅ 直接替换
📦 8-TSSOP
Same 10 MHz architecture and TSSOP footprint; ordering suffix changes the temperature or qualification designation.

📋 参考替代料(不在目录中)

MCP6021T-I/ST

✅ 直接替换
📦 8-TSSOP
Same 10 MHz architecture and TSSOP footprint; industrial suffix differs from the -E temperature designation.

📋 参考替代料(不在目录中)

MCP6021-E/ST 最大额定值与电气特性

Amplifier Type Single operational amplifier
拓扑 Voltage-feedback CMOS operational amplifier
Number of Circuits 1 circuit
Gain-Bandwidth Product 10 MHz
Supply Voltage Range 2.5 V to 5.5 V
Typical Operating Current 1.0 mA
Input Offset Voltage Less than 0.5 mV
Input Bias Current Low bias current
Input Common-Mode Range Rail-to-rail input
Output Swing Rail-to-rail output
Open-Loop Gain High open-loop gain
Temperature Grade Extended temperature grade
封装 8-pin TSSOP, 0.173 inch (4.40 mm) wide
安装类型 Surface mount
Terminals 8 terminals
Package Code ST
Technology Advanced CMOS

MCP6021-E/ST 引脚配置

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
引脚 1 OUT — Operational amplifier output
引脚 2 V- — Negative supply pin
引脚 3 +IN — Non-inverting input
引脚 4 V- — Negative supply pin
引脚 5 NC — Not connected
引脚 6 +IN — Non-inverting input
引脚 7 V+ — Positive supply pin
引脚 8 OUT — Operational amplifier output

典型应用

MCP6021-E/ST 适用于 6 应用s: Low-Side Current Sensing, Battery-Powered Sensor Conditioning, Active Filtering and Signal Conditioning, Audio Microphone Preamplification, Data Acquisition and Instrumentation, Industrial Control Signal Interface.

⚡

Low-Side Current Sensing

The MCP6021-E/ST fits low-side shunt amplifiers because its offset voltage is below 0.5 mV and its 10 MHz gain-bandwidth product preserves pulse-edge information that would otherwise be rounded by a slower amplifier. Place the shunt in the return path of the monitored load, connect the amplifier across the shunt-generated differential voltage, and bias the non-inverting input near mid-supply. The 1.0 mA typical operating current is useful in portable instruments, while the 2.5 V minimum supply permits operation from a 3.3 V rail. Verify that the maximum common-mode voltage and output swing remain valid across the expected load current and temperature.

🧩

Battery-Powered Sensor Conditioning

The MCP6021-E/ST provides a practical analog front end for low-power sensors operating from 3.3 V or 5 V because it combines a 2.5 V to 5.5 V supply range with a 1.0 mA typical operating current. Its rail-to-rail input stage accepts signals near the supply rails, while the rail-to-rail output stage maximizes usable signal range in a compact design. Configure it as a non-inverting gain stage around a resistive sensor or as an inverting amplifier for a bridge-derived signal. Keep the sensor return and amplifier ground in the same reference path to prevent ground differences from appearing as genuine sensor output.

🔧

Active Filtering and Signal Conditioning

The MCP6021-E/ST is suitable for first-order or higher-order active filters because its 10 MHz gain-bandwidth product leaves frequency headroom above the passband while keeping operating current around 1.0 mA. Rail-to-rail input and output operation increases the usable dynamic range in low-voltage filter stages. Use precision feedback resistors and capacitors, and keep the filter's noise gain and stability requirements within the amplifier's recommended operating region. The extended-temperature ordering grade also supports designs where operating conditions extend beyond a conventional commercial-grade temperature range.

🎧

Audio Microphone Preamplification

The MCP6021-E/ST can condition a microphone or other low-level audio source in a compact 3.3 V or 5 V circuit. Its rail-to-rail input accepts the small bipolar signal without requiring a conventional mid-supply input bias, while its 10 MHz bandwidth provides ample margin for audio-band amplification. The 1.0 mA typical operating current suits battery-powered equipment, and the low offset voltage limits DC error at the input. Choose resistor and capacitor values that set the intended gain and bandwidth, and follow the manufacturer datasheet for input capacitance and noise considerations.

📟

Data Acquisition and Instrumentation

The MCP6021-E/ST is useful as the analog input stage of a compact data-acquisition system where a transducer produces a signal close to the analog supply rail. The rail-to-rail input and output stages reduce headroom constraints, while the 10 MHz gain-bandwidth product supports faster settling than the device's 1.0 mA operating current would suggest for many low-frequency instruments. Place input protection ahead of the amplifier, filter high-frequency noise without pushing the amplifier into an unstable noise-gain region, and maintain a single ground reference between the transducer, analog amplifier, and converter interface.

🏭

Industrial Control Signal Interface

The MCP6021-E/ST can buffer industrial control signals running from 2.5 V to 5.5 V logic levels when the interface requires amplification rather than only logic translation. Its low 1.0 mA typical operating current and 10 MHz bandwidth allow it to drive downstream circuitry without adding substantial supply demand. Configure the amplifier for the required gain and polarity, and confirm the connected input device's output levels do not exceed the absolute maximum input ratings. For factory equipment, evaluate EMI susceptibility, input protection, and grounding against the enclosure and cabling environment.

What are the key specifications of MCP6021-E/ST that engineers should know?
The MCP6021-E/ST is a single 10 MHz, rail-to-rail input and output operational amplifier operating from 2.5 V to 5.5 V with a typical current of 1.0 mA. According to the Microchip MCP6021 datasheet, its input offset voltage is below 0.5 mV and it uses advanced CMOS technology. The device is supplied in an 8-pin TSSOP with an extended-temperature grade designation.
Where can I download the MCP6021 datasheet PDF?
The MCP6021 datasheet PDF is available from Microchip Technology at the official DeviceDoc URL for document 20001685E. It covers the MCP6021, MCP6021R, MCP6022, MCP6023, and MCP6024 families, including electrical characteristics, pin configurations, typical performance curves, and application information. Use the pin-description table in that document when assigning PCB tracks for the /ST TSSOP package.
Where can I find the MCP6021-E/ST pinout?
The MCP6021-E/ST pinout is documented in the Microchip MCP6021 family datasheet under the pin-configuration section for the 8-pin TSSOP package. The package contains one output, two supply pins, two non-inverting inputs, one inverting input, and one no-connect position. Verify pin numbering against the package drawing before routing a new PCB, particularly because the same family is offered in several package configurations.
What is the MCP6021 op amp and what is it used for?
The MCP6021 is a single voltage-feedback CMOS operational amplifier with rail-to-rail input and output capability, a 10 MHz gain-bandwidth product, and a 1.0 mA typical operating current. According to the Microchip manufacturer datasheet, it is intended for general-purpose signal conditioning from 2.5 V to 5.5 V. Typical uses include sensor amplifiers, current-sense amplifiers, active filters, and low-voltage audio input stages.
Is the MCP6021-E/ST suitable for 3.3 V and 5 V systems?
Yes, the MCP6021-E/ST supports both 3.3 V and 5 V rails because its specified supply range is 2.5 V to 5.5 V. Its rail-to-rail inputs are particularly useful when a sensor signal approaches the lower rail, while the rail-to-rail output expands usable output range. Keep the supply within 5.5 V and observe the absolute maximum ratings stated in the manufacturer datasheet.
What can replace the MCP6021-E/ST in an existing circuit?
The closest same-family TSSOP replacement is MCP6021T-E/ST, which retains the MCP6021 electrical function and pin arrangement while using a different temperature-grade suffix. MCP6021T-I/ST is another pin-compatible same-family option with an industrial temperature designation. Confirm package dimensions, temperature range, and the specific parameters required by the circuit against each device datasheet before substituting the part.
Is the MCP6021-E/ST the same as MCP6021T-E/ST?
The MCP6021-E/ST and MCP6021T-E/ST are closely related MCP6021 variants with the same 10 MHz rail-to-rail amplifier architecture and TSSOP package code, but their ordering suffixes specify different qualification or temperature grades. They are therefore practical pin-compatible choices when the required grade is acceptable. Review the ordering information and temperature ratings in the Microchip family datasheet for the exact production requirements.
When should I choose MCP6021-E/ST over MCP6021T-E/ST?
Choose MCP6021-E/ST when the design requires the extended-temperature ordering designation associated with the -E suffix and the MCP6021 TSSOP package. Choose MCP6021T-E/ST when its specified temperature and qualification profile better matches the product requirements. Both retain the same fundamental 10 MHz, rail-to-rail amplifier function, so the decision should be based on the verified suffix-specific ratings rather than signal-path performance.
Is MCP6021-E/ST suitable for a current-sensing amplifier?
Yes, the MCP6021-E/ST can amplify the differential voltage produced by a low-value shunt resistor. Its offset voltage below 0.5 mV and 10 MHz gain-bandwidth product are useful for low-side current measurement, while the 1.0 mA typical operating current suits compact systems. Check common-mode range, output swing, and shunt-driven error at the production temperature before finalizing the gain.
What is the best Microchip equivalent for MCP6021-E/ST?
The best same-family Microchip alternative found for the MCP6021-E/ST is the MCP6021T-E/ST, which retains the same 10 MHz rail-to-rail amplifier architecture and 8-pin TSSOP format while using a different ordering suffix. MCP6021T-I/ST provides another pin-compatible TSSOP choice with an industrial temperature designation. Select the version whose documented temperature and qualification requirements match the application.
Where can I buy MCP6021-E/ST online?
Use the Request a Quote form on this page to request MCP6021-E/ST availability, current commercial terms, and a delivery quotation for your required quantity. The form allows the request to be reviewed against the exact MCP6021-E/ST ordering code, including the 8-pin TSSOP package. Confirm current stock, minimum order quantity, and lead time directly through that quotation workflow.
What is the price of MCP6021-E/ST?
The MCP6021-E/ST is offered through a quote-first purchasing workflow on this page. Use the Request a Quote form to obtain the current commercial price for the quantity, packing, and delivery requirements of your project. The form is the appropriate channel for a current price because component pricing and inventory can change independently of a product page.
What is the lead time for MCP6021-E/ST?
Request the current MCP6021-E/ST lead time through the Request a Quote form on this page. Include the required quantity, reel or cut-tape preference, target shipment region, and any scheduled production date so the quotation can be evaluated accurately. A confirmed lead time should be obtained for the exact ordering code rather than inferred from a generic family listing.
Is MCP6021-E/ST in stock?
The current MCP6021-E/ST inventory status should be confirmed through the Request a Quote form on this page. Provide the required quantity and packing method in the request so the order can be matched to available production and distribution stock. Avoid treating a distributor search result as a reservation, because available inventory can change before the quotation is issued.
How should I decouple and route the MCP6021-E/ST circuit?
Place the supply bypass capacitor as close as practical to the MCP6021 VDD pin and connect the return path directly to the VSS pin. Keep the non-inverting input and inverting feedback trace short, and avoid routing them parallel to switching-node or high-current traces. The 2.5 V to 5.5 V operating range and low 1.0 mA typical current make the device suitable for low-power systems, but the bypass network remains essential for stable operation.

工程参考数据: MCP6021-E/ST ——对比、设计指导和合规信息。

选型指南

Choose MCP6021-E/ST for compact 2.5 V to 5.5 V signal-conditioning designs that need rail-to-rail input and output swing, a 10 MHz gain-bandwidth product, and low typical operating current of 1.0 mA. It is a strong fit for low-side current measurement, rail-based sensor signals, active filtering, and general-purpose analog front ends. MCP6021T-E/ST is the closest same-family TSSOP option when its suffix-specific temperature or qualification profile is preferred while retaining the 10 MHz architecture. MCP6021T-I/ST is appropriate when an industrial temperature designation is required and the rest of the electrical specification remains acceptable. The three MPNs share the 8-TSSOP pin-compatible format, so the selection should primarily follow the ordering-table temperature and qualification requirements. Confirm the exact common-mode limits, offset limits, output-swing curve, and absolute maximum ratings at the production temperature before final release.

与替代料对比

参数 本产品 MCP6021T-E/ST MCP6021T-I/ST
Brand Microchip Technology Microchip Technology Microchip Technology
Package 8-TSSOP 8-TSSOP - same footprint 8-TSSOP - same footprint
Amplifier Type Single general-purpose operational amplifier Single general-purpose operational amplifier Single general-purpose operational amplifier
Gain-Bandwidth Product 10 MHz 10 MHz 10 MHz
Supply Voltage Range 2.5 V to 5.5 V 2.5 V to 5.5 V 2.5 V to 5.5 V
Typical Operating Current 1.0 mA 1.0 mA 1.0 mA
Input Offset Voltage Less than 0.5 mV Less than 0.5 mV Less than 0.5 mV
Input and Output Common Mode Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output
Application Class General-purpose amplifier General-purpose amplifier General-purpose amplifier

关键差异点

  • Combines wide signal-headroom operation with low supply demand (对比 MCP6021T-E/ST)
  • Direct TSSOP family interchangeability (对比 MCP6021T-I/ST)
  • Single-amplifier pinout preserves board area (对比 MCP6021T-E/ST)

设计说明

Place the supply bypass capacitor directly beside the MCP6021 VDD pin and connect its return to the VSS pin without routing through a noisy analog region. Keep the non-inverting input trace and the inverting feedback trace short and away from switching nodes. The rail-to-rail input stage accepts a wide common-mode range, but it does not remove the need for short, shielded routing of sensitive sensor signals.

Choose closed-loop bandwidth and feedback-network values that preserve stability at the operating gain. For non-inverting stages, add a compensating capacitor across the inverting feedback resistor when required by the manufacturer guidance. For capacitive sensor inputs, limit total input capacitance and isolate the amplifier with a small series resistor to avoid excessive overshoot or oscillation.

Do not assume that the rail-to-rail input and output ratings permit operation beyond the absolute maximum input voltages. Keep signals and supply pins within the manufacturer limits, verify output-current capability for the load, and check output swing at the required temperature. Also avoid interpreting the below-0.5 mV offset specification as a guaranteed maximum for every unit; use the manufacturer test limits when designing a precision error budget.

Estimated: with a 5.5 V supply, a 3.3 V output, and a 1 mA load, the amplifier's internal dissipation is approximately 2.2 mW before accounting for output-stage and bias variations. Estimated junction-temperature rise is therefore negligible under normal conditions, but the PCB still needs adequate copper around the TSSOP for reliable assembly and production repeatability.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The manufacturer product material and family datasheet identify the device and its package, but the available listing material does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Verify these attributes against the current manufacturer product page and declaration documents before qualification.

相关搜索

mcp6021 datasheet mcp6021 datasheet pdf mcp6021 price mcp6021 op amp mcp6021 equivalent MCP6021-E/ST datasheet MCP6021-E/ST pinout MCP6021-E/ST 8-TSSOP MCP6021-E/ST replacement MCP6021-E/ST vs MCP6021T-E/ST MCP6021-E/ST current sensing Microchip MCP6021-E/ST MCP6021-E/ST buy MCP6021-E/ST stock

相关元器件 & 术语

Microchip Technology MCP6021 MCP6021-E/ST MCP6021T-E/ST MCP6021T-I/ST MCP6021 family operational amplifier voltage-feedback amplifier CMOS analog IC rail-to-rail input rail-to-rail output gain-bandwidth product input offset voltage input bias current common-mode voltage TSSOP-8 surface-mount package 3.3 V system 5 V analog rail low-side current sensing active filter sensor signal conditioning audio preamplifier industrial control interface
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情