MCP6021-E/ST - 10MHz RRO Op Amp | Microchip Technology
MPN: MCP6021-E/ST ✓ فعالMCP6021-E/ST نمای کلی
An operational amplifier is an active analog component that amplifies the difference between voltages applied to its inverting and non-inverting inputs. The MCP6021 belongs to the hierarchy of operational amplifier, voltage-feedback amplifier, analog signal IC, and semiconductor. Its rail-to-rail input stage accepts signals close to either supply rail, while its rail-to-rail output stage provides a wide output swing. This makes it useful when the signal range leaves little headroom above or below the supply voltages.
Principal features include a 10 MHz gain-bandwidth product, low typical operating current of 1.0 mA, an offset voltage below 0.5 mV, and low input bias current. The 2.5 V minimum supply voltage supports 3.3 V and 5 V systems. The -E suffix identifies the extended-temperature product grade, while the /ST package code denotes the 8-pin TSSOP configuration. The wide operating range makes the device applicable to industrial control, sensor interfaces, battery-powered equipment, and audio input conditioning.
The MCP6021 uses advanced CMOS technology and a voltage-feedback architecture. At unity gain, its approximately 10 MHz bandwidth provides useful response for low-frequency measurement, current sensing, and active filtering. A single amplifier can be configured as a non-inverting stage, inverting stage, voltage follower, comparator-style interface, or transimpedance front end. The low 1.0 mA operating current reduces supply demand in portable systems, although actual consumption varies with supply voltage, output swing, frequency, and load.
Typical applications include low-voltage sensor conditioning, current sensing, active filters, audio microphone preamplification, data acquisition, and general-purpose analog signal chains. For a current-sensing application, the amplifier can amplify the small voltage generated across a shunt resistor while its rail-to-rail inputs accept signals near the lower supply rail. For active filtering, the 10 MHz bandwidth leaves margin above the filter corner frequency while limiting the required supply current.
Design with the 2.5 V to 5.5 V supply range and input common-mode limits in mind. Keep input and feedback traces short, place decoupling capacitors close to the supply pins, and avoid routing sensitive input signals beside digital switching nodes. Follow the manufacturer datasheet pin-description table when assigning PCB tracks, and confirm the extended-temperature limits and automotive-grade requirements for the exact ordering code before production release.
جایگزینهای drop-in برای MCP6021-E/ST — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
MCP6021T-E/ST
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6021T-I/ST
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6021-E/ST حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Single operational amplifier |
| توپولوژی | Voltage-feedback CMOS operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 10 MHz |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Typical Operating Current | 1.0 mA |
| Input Offset Voltage | Less than 0.5 mV |
| Input Bias Current | Low bias current |
| Input Common-Mode Range | Rail-to-rail input |
| Output Swing | Rail-to-rail output |
| Open-Loop Gain | High open-loop gain |
| Temperature Grade | Extended temperature grade |
| بستهبندی | 8-pin TSSOP, 0.173 inch (4.40 mm) wide |
| نوع نصب | Surface mount |
| Terminals | 8 terminals |
| Package Code | ST |
| Technology | Advanced CMOS |
پیکربندی پین MCP6021-E/ST
| پین 1 | OUT — Operational amplifier output |
| پین 2 | V- — Negative supply pin |
| پین 3 | +IN — Non-inverting input |
| پین 4 | V- — Negative supply pin |
| پین 5 | NC — Not connected |
| پین 6 | +IN — Non-inverting input |
| پین 7 | V+ — Positive supply pin |
| پین 8 | OUT — Operational amplifier output |
کاربردهای معمول
MCP6021-E/ST مناسب است برای 6 کاربردs: Low-Side Current Sensing, Battery-Powered Sensor Conditioning, Active Filtering and Signal Conditioning, Audio Microphone Preamplification, Data Acquisition and Instrumentation, Industrial Control Signal Interface.
Low-Side Current Sensing
The MCP6021-E/ST fits low-side shunt amplifiers because its offset voltage is below 0.5 mV and its 10 MHz gain-bandwidth product preserves pulse-edge information that would otherwise be rounded by a slower amplifier. Place the shunt in the return path of the monitored load, connect the amplifier across the shunt-generated differential voltage, and bias the non-inverting input near mid-supply. The 1.0 mA typical operating current is useful in portable instruments, while the 2.5 V minimum supply permits operation from a 3.3 V rail. Verify that the maximum common-mode voltage and output swing remain valid across the expected load current and temperature.
پیشنهادی
Battery-Powered Sensor Conditioning
The MCP6021-E/ST provides a practical analog front end for low-power sensors operating from 3.3 V or 5 V because it combines a 2.5 V to 5.5 V supply range with a 1.0 mA typical operating current. Its rail-to-rail input stage accepts signals near the supply rails, while the rail-to-rail output stage maximizes usable signal range in a compact design. Configure it as a non-inverting gain stage around a resistive sensor or as an inverting amplifier for a bridge-derived signal. Keep the sensor return and amplifier ground in the same reference path to prevent ground differences from appearing as genuine sensor output.
پیشنهادی
Active Filtering and Signal Conditioning
The MCP6021-E/ST is suitable for first-order or higher-order active filters because its 10 MHz gain-bandwidth product leaves frequency headroom above the passband while keeping operating current around 1.0 mA. Rail-to-rail input and output operation increases the usable dynamic range in low-voltage filter stages. Use precision feedback resistors and capacitors, and keep the filter's noise gain and stability requirements within the amplifier's recommended operating region. The extended-temperature ordering grade also supports designs where operating conditions extend beyond a conventional commercial-grade temperature range.
پیشنهادی
Audio Microphone Preamplification
The MCP6021-E/ST can condition a microphone or other low-level audio source in a compact 3.3 V or 5 V circuit. Its rail-to-rail input accepts the small bipolar signal without requiring a conventional mid-supply input bias, while its 10 MHz bandwidth provides ample margin for audio-band amplification. The 1.0 mA typical operating current suits battery-powered equipment, and the low offset voltage limits DC error at the input. Choose resistor and capacitor values that set the intended gain and bandwidth, and follow the manufacturer datasheet for input capacitance and noise considerations.
پیشنهادی
Data Acquisition and Instrumentation
The MCP6021-E/ST is useful as the analog input stage of a compact data-acquisition system where a transducer produces a signal close to the analog supply rail. The rail-to-rail input and output stages reduce headroom constraints, while the 10 MHz gain-bandwidth product supports faster settling than the device's 1.0 mA operating current would suggest for many low-frequency instruments. Place input protection ahead of the amplifier, filter high-frequency noise without pushing the amplifier into an unstable noise-gain region, and maintain a single ground reference between the transducer, analog amplifier, and converter interface.
پیشنهادی
Industrial Control Signal Interface
The MCP6021-E/ST can buffer industrial control signals running from 2.5 V to 5.5 V logic levels when the interface requires amplification rather than only logic translation. Its low 1.0 mA typical operating current and 10 MHz bandwidth allow it to drive downstream circuitry without adding substantial supply demand. Configure the amplifier for the required gain and polarity, and confirm the connected input device's output levels do not exceed the absolute maximum input ratings. For factory equipment, evaluate EMI susceptibility, input protection, and grounding against the enclosure and cabling environment.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP6021-E/ST — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP6021T-E/ST | MCP6021T-I/ST |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-TSSOP | 8-TSSOP - same footprint | 8-TSSOP - same footprint |
| Amplifier Type | Single general-purpose operational amplifier | Single general-purpose operational amplifier | Single general-purpose operational amplifier |
| Gain-Bandwidth Product | 10 MHz | 10 MHz | 10 MHz |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Typical Operating Current | 1.0 mA | 1.0 mA | 1.0 mA |
| Input Offset Voltage | Less than 0.5 mV | Less than 0.5 mV | Less than 0.5 mV |
| Input and Output Common Mode | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Application Class | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier |
تفاوتهای کلیدی
- Combines wide signal-headroom operation with low supply demand (در مقابلMCP6021T-E/ST)
- Direct TSSOP family interchangeability (در مقابلMCP6021T-I/ST)
- Single-amplifier pinout preserves board area (در مقابلMCP6021T-E/ST)
یادداشتهای طراحی
Place the supply bypass capacitor directly beside the MCP6021 VDD pin and connect its return to the VSS pin without routing through a noisy analog region. Keep the non-inverting input trace and the inverting feedback trace short and away from switching nodes. The rail-to-rail input stage accepts a wide common-mode range, but it does not remove the need for short, shielded routing of sensitive sensor signals.
Choose closed-loop bandwidth and feedback-network values that preserve stability at the operating gain. For non-inverting stages, add a compensating capacitor across the inverting feedback resistor when required by the manufacturer guidance. For capacitive sensor inputs, limit total input capacitance and isolate the amplifier with a small series resistor to avoid excessive overshoot or oscillation.
Do not assume that the rail-to-rail input and output ratings permit operation beyond the absolute maximum input voltages. Keep signals and supply pins within the manufacturer limits, verify output-current capability for the load, and check output swing at the required temperature. Also avoid interpreting the below-0.5 mV offset specification as a guaranteed maximum for every unit; use the manufacturer test limits when designing a precision error budget.
Estimated: with a 5.5 V supply, a 3.3 V output, and a 1 mA load, the amplifier's internal dissipation is approximately 2.2 mW before accounting for output-stage and bias variations. Estimated junction-temperature rise is therefore negligible under normal conditions, but the PCB still needs adequate copper around the TSSOP for reliable assembly and production repeatability.
اطلاعات انطباق
The manufacturer product material and family datasheet identify the device and its package, but the available listing material does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Verify these attributes against the current manufacturer product page and declaration documents before qualification.