MK20DX64VLH7 - 72MHz Cortex-M4 64KB Flash MCU | NXP
料号: MK20DX64VLH7 ✓ 量产中MK20DX64VLH7 概述
A microcontroller is a programmable system-on-chip that integrates a processor core, memory, timers, analog converters, communication interfaces, and control peripherals on one device. The Kinetis K20 family occupies the middle of NXP's Kinetis portfolio, bridging simple entry-level control and higher-performance Cortex-M4 applications. Its ARM Cortex-M4 architecture supports efficient event-driven control, while the integrated analog resources reduce the need for external components.
The MK20DX64VLH7 combines a 72 MHz Cortex-M4 core with 64 KB of program flash and 16 KB of SRAM. Verified product information identifies high-precision analog integration, flexible low-power operation, and a suite of communication, timing, and control peripherals. Its operating voltage extends from 1.71 V to 3.6 V, allowing deployment in low-voltage industrial equipment while retaining the processing margin needed for mixed signal control loops.
The 64-LQFP package exposes a conventional leaded footprint that supports assembly and inspection processes requiring through-hole component handling. Its 64-pin count provides access to the K20 family's GPIO, communication, timer, analog, debug, and power functions. Exact peripheral multiplexing and alternate-function assignments must be assigned from the NXP pin-muxing documentation for the selected board configuration.
Typical applications include industrial controllers, connected metering equipment, motor-control and automation systems, sensor nodes, and compact embedded instruments. The 72 MHz processing rate is suitable for responsive supervisory loops, while the integrated analog peripherals support measurements and control functions close to the processor. The 16 KB SRAM helps accommodate working state, communication buffers, and time-critical data without requiring an external memory device in many designs.
Design the supply rails to remain within the 1.71 V to 3.6 V operating range, including transient conditions at the pins. Provide the required decoupling close to the power terminals, use a supported NXP programming and debug interface, and verify every peripheral pin assignment against the manufacturer datasheet and pin-muxing table before PCB release.
This page combines procurement-oriented component data, compatible family alternatives, application guidance, comparison parameters, and practical design notes to support faster engineering evaluation of the MK20DX64VLH7.
直接替换替代料: MK20DX64VLH7 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MK20DX64VLH7 (相同外形与封装尺寸) ——差异在于 Package, ADC Resolution, Flash Memory, SRAM, Temperature Grade.
MK20DX128VLH7
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MK20DX256VLH7
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MK20DX32VLH7
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MK21DX128VLH7
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MK21DX256VLH7
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MK20DX64VLH7 最大额定值与电气特性
| Product Type | 32-bit ARM Cortex-M4 microcontroller |
| Product Family | Kinetis K20 |
| Maximum CPU Frequency | 72 MHz |
| Flash Memory | 64 KB |
| Flash Organization | 64K x 8 bits |
| SRAM | 16 KB |
| Operating Voltage Range | 1.71 V to 3.6 V |
| Architecture | ARM 32-bit RISC |
| Core | ARM Cortex-M4 |
| 封装 | 64-LQFP, 10 x 10 mm |
| Terminal Count | 64 pins |
| 安装类型 | Surface mount |
| Terminal Form | Gull wing |
| Package Shape | Square |
| Temperature Grade | Industrial grade |
| ADC Resolution | 12-bit and 16-bit |
| 生命周期状态 | Active |
MK20DX64VLH7 square 引脚配置指南
MK20DX64VLH7(square 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: MK20DX64VLH7.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MK20DX64VLH7 适用于 6 应用s: Industrial Control and Automation, Smart Metering and Data Acquisition, Motor Control and Actuator Interface, Communication Gateway and Sensor Node, Battery-Powered Embedded Instrument, Robotics and Condition Monitoring.
Industrial Control and Automation
The MK20DX64VLH7 fits supervisory control, sequencing, and machine-interface boards because its 72 MHz Cortex-M4 core provides useful processing headroom while 64 KB of flash and 16 KB of SRAM support embedded control firmware. The 1.71 V to 3.6 V range supports low-voltage industrial rails, and the integrated analog, timer, and communication resources reduce external component count. Use the MCU beside optically isolated interfaces, status indicators, and sensor conditioning. Before layout release, confirm every alternate-function assignment, oscillator requirement, and power terminal connection against the NXP pin-muxing documentation.
推荐
Smart Metering and Data Acquisition
MK20DX64VLH7 is appropriate for compact metering equipment that combines signal measurement, local display control, and communications. Its 12-bit and 16-bit ADC resources support acquisition tasks, while the 72 MHz Cortex-M4 core can manage filtering, calibration, data packing, and communication protocols. The 16 KB SRAM provides useful working space for buffers and state handling. Use the device with a precision current or voltage front end, and verify analog accuracy, reference requirements, and acquisition timing in the manufacturer electrical characteristics. Firmware should also include calibration, overflow handling, and sensor diagnostics.
推荐
Motor Control and Actuator Interface
The MK20DX64VLH7 can coordinate motor-control supervisory functions, position or event counting, fault handling, and communication with a dedicated power stage. Its 72 MHz processor supports responsive control tasks, while integrated timers and analog resources help synchronize command sequencing with measured conditions. The 64-LQFP package provides access to a broad pin set for encoder, control, and status signals. Keep high-current switching paths separate from sensitive analog routing, validate timer pin multiplexing, and include hardware shutdown paths so a firmware fault cannot leave an actuator energized.
推荐
Communication Gateway and Sensor Node
MK20DX64VLH7 supports an embedded gateway or sensor node that must acquire local inputs, run control logic, and communicate with a higher-level system. Its Cortex-M4 core handles protocol state machines and timing, while the family’s communication and low-power peripherals support responsive operation between external events. The 64 KB flash footprint is suitable for moderate protocol stacks and application firmware. Select the operating clock and sleep mode explicitly, provide clean local decoupling, and reserve programming access for production configuration. If the protocol stack exceeds available memory, move to the 128 KB or 256 KB family variant.
推荐
Battery-Powered Embedded Instrument
MK20DX64VLH7 is suitable for compact, battery-powered instruments where a 72 MHz control processor and integrated analog resources must coexist with low-power operation. Its 1.71 V minimum operating voltage permits operation from appropriately regulated low-voltage rails, while low-power modes can reduce consumption during measurement intervals. The 16 KB SRAM helps avoid continuous external-memory access. Choose capacitors and regulators for low-leakage operation, disable unused peripherals and pin functions, and use the manufacturer low-power guidance to establish wake-up timing. Battery life must be evaluated with the actual sensor, communications, and indicator load.
推荐
Robotics and Condition Monitoring
MK20DX64VLH7 can serve as the local controller in a robot or condition-monitoring module that combines sensor fusion, event logic, and communications. The Cortex-M4 processing capability supports filtering and control algorithms, while the integrated analog functions allow several sensor inputs to be handled close to the processor. The 64-LQFP package provides a practical leaded footprint for industrial or service assemblies. Keep analog grounds and digital return currents organized, protect exposed sensor inputs from transients, and define deterministic watchdog and fault-response behavior. A larger-memory variant is preferable when logging or complex algorithms exceed the 64 KB code budget.
推荐
推荐产品汇总
工程参考数据: MK20DX64VLH7 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MK20DX128VLH7 | MK20DX256VLH7 | MK20DX32VLH7 | MK21DX128VLH7 | MK21DX256VLH7 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) |
| Flash Memory | 64 KB | 128 KB | 256 KB | 32 KB | 128 KB | 256 KB |
| Product Family | Kinetis K20 | Kinetis K20 | Kinetis K20 | Kinetis K20 | Kinetis K21 | Kinetis K21 |
关键差异点
- Provides a compact 64 KB configuration for embedded applications (对比 MK20DX32VLH7)
- Avoids unnecessary memory capacity for moderate firmware loads (对比 MK20DX256VLH7)
- Combines a 72 MHz Cortex-M4 core with a 64 KB memory footprint (对比 MK21DX128VLH7)
设计说明
Design the supply network around the verified 1.71 V to 3.6 V operating range. Place the manufacturer's recommended bypass capacitors directly beside the device power terminals, minimize loop area, and account for voltage tolerance, startup ramp, and transient current. Separate sensitive analog and digital return paths where the layout guidance permits it. Verify brownout behavior, debug connection effects, and peripheral current before the board enters production.
Use the NXP package drawing and pin-muxing table as the controlling references for the 64-LQFP footprint. Check each signal's alternate-function mapping instead of assigning pins by familiarity with another Kinetis device. Keep programming, debug, and reset access reachable, preserve the required clock layout, and provide adequate copper and thermal pathways around the leaded package. Do not release the layout until every unused terminal has been reviewed.
Do not assume that a same-package Kinetis variant is firmware-compatible without checking the memory map, vector table, peripheral set, clock configuration, and startup code. The 32 KB alternative may not contain the current firmware, while the 128 KB and 256 KB alternatives may alter available peripheral functions. K21-family candidates require an especially careful hardware and software review. Update bootloader support and validate production programming before substituting any alternative.
Keep oscillator, precision analog, and communication routes away from switching power stages and high-current actuator traces. Match external network values to the manufacturer reference configurations, and avoid long unprotected analog inputs. Use a continuous ground reference under the device where the package and layout guidance allow it. For mixed-signal designs, establish a clear partition between sensing, digital processing, and power-return paths before assigning connector and component locations.
合规信息
The manufacturer product page identifies the device as active and provides environmental-quality information, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statuses are not included in the accessible product data.