MPC8536BVTANGA - PowerQUICC III 800MHz e500 MPU | NXP Semiconductors
料号： MPC8536BVTANGA ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $120.5 | $120.50 |
| 10 | $115 | $1,150.00 |
| 100 | $108.5 | $10,850.00 |
| 500 | $102 | $51,000.00 |
| 1,000 | $95 | $95,000.00 |
MPC8536BVTANGA 概述
A microprocessor (MPU) is an integrated circuit that contains the central processing unit, cache, memory controller, and peripheral interfaces of a computer system on a single die. The MPC85xx family belongs to the Power Architecture microprocessor hierarchy, sitting under the broader PowerPC processor lineage and the wider RISC processor category. PowerQUICC III parts combine CPU cores with communications peripherals, making them a subclass of system-on-chip (SoC) devices optimized for networking and telecom workloads rather than general-purpose compute.
Key features of the MPC8536BVTANGA include integrated DDR2/DDR3 memory controller with ECC, dual Gigabit Ethernet controllers, SATA controller, dual PCI/PCIe controllers, SDHC interface, and USB 2.0 interface. The e500 core includes a 32 KB L1 instruction cache and 32 KB L1 data cache, plus a 256 KB unified L2 cache with ECC support. Hardware-accelerated cryptography is absent on this non-E variant, distinguishing it from the MPC8536E which adds SEC 2.0 acceleration.
The architecture pairs the e500 core with a system bus and peripheral block, allowing concurrent operation of the CPU and I/O subsystems. The device uses a 783-pin FCBGA (Flip-Chip Ball Grid Array) package with 1 mm ball pitch, requiring multi-layer PCB design with controlled-impedance routing and matched-length DDR traces for reliable operation.
Common applications include IP network routers, secure routers, industrial control gateways, network-attached storage (NAS) controllers, and wireless base station controllers. The wide integration of communications peripherals makes it suitable for designs that previously required a CPU plus multiple companion ICs.
When designing with the MPC8536BVTANGA, ensure the PCB supports the FCBGA thermal envelope (case temperature must stay below 105C). Provide adequate decoupling across all supply rails and follow NXP's reference design for DDR trace length matching. Production designs should validate boot code against the specific revision of the integrated development environment.
This page synthesizes distributor pricing, drop-in alternative MPNs within the MPC85xx family, and practical design considerations not consolidated in the manufacturer datasheet alone.
直接替换替代料： MPC8536BVTANGA ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MPC8536BVTANGA （相同外形与封装尺寸） ——差异在于 Ethernet, Memory Controller, Package, USB, Core Architecture.
快速对比工具——选择替代料号进行并排对比：
MPC8536BVJANGA
✅ 直接替换✓ 有现货
$132.1 / 个
查看数据手册 →MPC8536AVTANGA
✅ 直接替换📋 参考替代料（不在目录中）
MPC8536EAVTANGA
✅ 直接替换✓ 有现货
$84.75 / 个
查看数据手册 →MPC8536BVJANG
✅ 直接替换📋 参考替代料（不在目录中）
MPC8536EAVTAVLA
✅ 直接替换✓ 有现货
$72 / 个
查看数据手册 →MPC8536BVTANGA 最大额定值与电气特性
| Core Architecture | Power Architecture e500 |
| 数据总线宽度 | 32-bit |
| Core Frequency | 800 MHz |
| 封装 | 783-FCBGA (29x29 mm, 1 mm pitch) |
| Core Supply Voltage | 1.1 V |
| I/O Supply Voltages | 1.5 V / 1.8 V / 2.5 V / 3.3 V |
| 工作温度 | 0C to 105C |
| L1 Instruction Cache | 32 KB |
| L1 Data Cache | 32 KB |
| L2 Cache | 256 KB unified, with ECC |
| Memory Controller | DDR2 / DDR3 with ECC |
| Ethernet | Dual Gigabit Ethernet (eTSEC) |
| PCI / PCIe | PCI and PCIe interfaces |
| SATA | SATA controller integrated |
| Storage Interface | SDHC |
| USB | USB 2.0 |
| Cryptography | Not present (non-E variant) |
| RoHS 状态 | Compliant (lead-free FCBGA) |
MPC8536BVTANGA 783-fcbga (29x29 mm, 1 mm pitch) 引脚配置指南
MPC8536BVTANGA（783-fcbga (29x29 mm, 1 mm pitch) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MPC8536BVTANGA.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MPC8536BVTANGA 适用于 6 应用s: IP Network Routers and Edge Gateways, Secure VPN Concentrators, Network-Attached Storage (NAS) Controllers, Industrial Control Gateways, Wireless Base Station Controllers, Print and Imaging Controller Boards.
IP Network Routers and Edge Gateways
The MPC8536BVTANGA fits IP network routers and edge gateways because its dual Gigabit Ethernet controllers, PCI/PCIe interfaces, and 800 MHz e500 core deliver line-rate packet processing for SMB routing workloads. The integrated DDR2/DDR3 controller with ECC provides the memory bandwidth required for routing table lookups and packet buffering. In typical deployments, the MPU sits between PHY transceivers on the network side and switch fabric on the data plane, replacing a discrete CPU-plus-NPU architecture and reducing BOM by approximately 30-40% per NXP reference platforms.
推荐
Secure VPN Concentrators
For secure VPN concentrators, the non-E variant of the MPC8536BVTANGA handles tunnel setup and control plane, while the E variant (MPC8536EAVTANGA) is preferred when SEC 2.0 hardware AES/SHA/RSA acceleration is needed for IPsec throughput. The dual GbE ports separate trusted and untrusted network segments, and the USB 2.0 interface supports external storage for log retention. At 800 MHz, the e500 core manages IKE negotiations and policy lookups for up to several hundred concurrent tunnels per NXP application notes.
推荐
Network-Attached Storage (NAS) Controllers
The MPC8536BVTANGA is suitable for NAS controllers because the integrated SATA controller, dual GbE for LAG bonding, and SDHC interface for boot media allow a single chip to control 4+ drive bays and dual network uplinks. The DDR3 controller with ECC supports the memory footprint required for ZFS or RAID cache tables. NXP reference designs use the MPU with external SATA multipliers to scale to 8-12 drive bays while keeping the host SoC at 800 MHz, balancing throughput against power dissipation.
推荐
Industrial Control Gateways
In industrial control gateways, the MPC8536BVTANGA operates reliably within its 0C to 105C industrial-extended temperature envelope, while the PCI/PCIe and USB 2.0 interfaces connect to fieldbus cards (Profibus, CAN, Modbus). The 800 MHz e500 core runs protocol translation stacks in real time, and the DDR3 with ECC detects single-bit memory errors in 24/7 industrial deployments. NXP application notes recommend this part for SCADA aggregation nodes and PLC bridges where deterministic interrupt latency is critical.
推荐
Wireless Base Station Controllers
The MPC8536BVTANGA targets small-cell and picocell base station controllers where its combination of dual GbE backhaul, PCI/PCIe for baseband cards, and USB 2.0 for diagnostics is sufficient for LTE femtocell class workloads. At 800 MHz, the e500 core runs L2/L3 stack and OAM tasks, while the integrated peripherals reduce the part count versus discrete CPU-plus-FPGA architectures. Reference designs from NXP integrate this MPU with RF transceiver cards for indoor small-cell deployments.
推荐
Print and Imaging Controller Boards
The MPC8536BVTANGA fits production print and imaging controllers because its USB 2.0, dual GbE, and PCI/PCIe support multiple connectivity options to print engines, scanners, and operator panels. The 800 MHz e500 core handles raster image processing and PDL interpretation, with the integrated SATA interface available for local spool storage. NXP has published reference designs pairing this MPU with DDR3 and external image processors for office-class multifunction printers.
推荐
推荐产品汇总
工程参考数据： MPC8536BVTANGA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MPC8536BVJANGA | MPC8536AVTANGA | MPC8536EAVTANGA | MPC8536BVJANG | MPC8536EAVTAVLA |
|---|---|---|---|---|---|---|
| Package | 783-FCBGA (29x29 mm) | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same | 783-FCBGA (29x29 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Frequency | 800 MHz | 600 MHz | 800 MHz | 800 MHz | 600 MHz | 800 MHz |
| Revision | B | B | A | E | B | E |
| SEC 2.0 Cryptography | No (non-E) | No (non-E) | No (non-E) | Yes | No (non-E) | Yes |
| DDR3 Support | Yes (improved B-revision AC margins) | Yes (B-revision) | Yes (A-revision) | Yes | Yes (B-revision) | Yes |
| Operating Temperature | 0C to 105C | 0C to 105C | 0C to 105C | 0C to 105C | 0C to 105C | Extended |
| RoHS Status | Compliant (lead-free) | Compliant (lead-free) | Compliant (lead-free) | Compliant (lead-free) | Compliant (lead-free) | Compliant (lead-free) |
关键差异点
- Higher CPU throughput than 600 MHz variant （对比 MPC8536BVJANGA)
- Improved DDR3 AC margins over A-revision （对比 MPC8536AVTANGA)
- Lower cost than crypto-enabled E variant （对比 MPC8536EAVTANGA)
设计说明
The 783-FCBGA package dissipates power through the die-down thermal path to PCB copper pours. Per NXP reference designs, allocate at least 25 cm^2 of 2 oz copper on top and bottom layers directly under the BGA array to keep junction temperature within the 105C case rating at 800 MHz full load. Thermal vias (0.3 mm pitch, filled) connecting inner copper planes significantly improve thermal performance in production designs.
PCB design must follow NXP's MPC8536 design guide for DDR3 trace routing. Match DQ/DQS trace lengths within 50 mil, route address/control traces within 100 mil of clock length, and maintain 50 ohm single-ended impedance (100 ohm differential for clock). Use 8-layer stackup minimum with dedicated ground planes beneath DDR signals. Series resistor placement on address/control nets improves signal integrity at DDR3-1066.
The MPC8536BVTANGA requires multiple supply rails: 1.1 V core, 1.5 V DDR3 termination, 1.8 V/2.5 V/3.3 V I/O. Decouple each rail with 0.1 uF ceramic capacitors placed within 5 mm of each supply ball group, plus bulk 10-47 uF tantalum or polymer capacitors near the package perimeter. Power sequencing must follow NXP's POR (power-on-reset) sequence to prevent latch-up - Vcore must rise before or simultaneous with I/O rails.
Common pitfalls include omitting the I2C EEPROM for boot configuration (required for non-SPI boot modes), misconnecting USB port power to the wrong supply rail, and forgetting to strap CONFIG pins before reset release. Boot code must validate the specific die revision because B-revision errata differ from A-revision. NXP's errata documents should be reviewed before firmware freeze.
合规信息
RoHS compliant per NXP product page. Lead-free FCBGA package. AEC-Q100 not applicable - this is an industrial/communications MPU, not automotive-qualified.
