MPC8547EVTAUJD - PowerQUICC III SoC, 1.333 GHz, 783-FCPBGA | NXP
料号： MPC8547EVTAUJD ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $185 | $185.00 |
| 10 | $168.5 | $1,685.00 |
| 100 | $149 | $14,900.00 |
| 500 | $132.75 | $66,375.00 |
| 1,000 | $118.4 | $118,400.00 |
MPC8547EVTAUJD 概述
PowerQUICC III processors are a category of integrated communications processors that combine a high-performance Power Architecture CPU core with extensive on-chip connectivity peripherals and a hardware-accelerated security block, optimized for routing, switching, wireless baseband, and industrial control equipment. Within the broader taxonomy, the MPC8547E sits below general-purpose FPGAs and above simple microcontrollers: it is a multiprocessor SoC for Layer 2-4 packet processing rather than a microcontroller or application processor. Compared with discrete CPU-plus-ASIC designs, integrating these subsystems reduces board area, validation time, and bill-of-materials cost.
Key capabilities include a 32-bit e500 core with double-precision floating point, dual 64-bit DDR2 SDRAM controllers with ECC, up to four Gigabit Ethernet controllers supporting SGMII and RGMII, two PCI Express interfaces, a PCI-X controller, two Serial RapidIO endpoints, four user-programmable serial interfaces, and a SEC 3.3 security engine accelerating AES, 3DES, SHA, and public-key operations. The local bus controller provides 8/16/32-bit data width support for NAND flash and other peripherals, while integrated DMA channels move packet data with minimal CPU involvement.
The MPC8547E architecture uses a hierarchical bus fabric connecting the e500 core to the L2 cache, DDR controllers, and peripheral bridges, ensuring deterministic throughput for control plane traffic. The platform is supported by standard Power Architecture toolchains, Linux Board Support Packages from major vendors, and the CodeWarrior development environment, enabling rapid firmware bring-up and field-proven software reuse in carrier and industrial deployments.
Typical applications include multiservice routers, edge and aggregation switches, wireless base station controllers, IP-PBX and media gateways, line cards, network-attached storage controllers, military signal processing platforms, and industrial automation controllers. The combination of SERDES, Ethernet MACs, and DDR2 memory makes it well suited to headless networking equipment that requires low jitter and predictable latency over hardware-accelerated packet processing paths.
When designing with the MPC8547EVTAUJD, careful PCB layout is mandatory: the 783-ball FCPBGA at 29 mm by 29 mm requires microvia stack-ups, matched-length SERDES traces for SGMII, Serial RapidIO, and PCI Express lanes, and a continuous ground reference plane. Power sequencing must follow NXP guidelines to avoid latch-up at cold start; a soft-start circuit and proper decoupling with 0.1 uF plus bulk ceramic caps at every voltage rail is required.
This page consolidates distributor pricing, drop-in alternative parts from the same PowerQUICC III family, and practical board-design guidance not found in the manufacturer datasheet alone.
直接替换替代料： MPC8547EVTAUJD ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MPC8547EVTAUJD （相同外形与封装尺寸） ——差异在于 Core Architecture, Package, Operating Temperature, RoHS Status, Maximum Core Frequency.
快速对比工具——选择替代料号进行并排对比：
MPC8547EVTAULJD
✅ 直接替换📋 参考替代料（不在目录中）
MPC8547EVTAUKD
✅ 直接替换📋 参考替代料（不在目录中）
MPC8548ECVTAQGD
✅ 直接替换✓ 有现货
$99.85 / 个
查看数据手册 →MPC8548EVTAQGD
✅ 直接替换📋 参考替代料（不在目录中）
MPC8548EVTAVJD
✅ 直接替换📋 参考替代料（不在目录中）
MPC8548EVTATGD
✅ 直接替换📋 参考替代料（不在目录中）
MPC8547EVTAUJD 最大额定值与电气特性
| Manufacturer | NXP Semiconductors |
| Series / Family | PowerQUICC III, MPC85xx (MPC8547E) |
| Core Architecture | Power Architecture e500, single core |
| Core Data Width | 32-bit |
| Maximum Core Frequency | 1.333 GHz |
| Maximum System Bus Frequency | 533 MHz |
| 封装 | 783-ball FCPBGA, 29 mm x 29 mm |
| Memory Controllers | Dual DDR2 SDRAM, 64-bit, with ECC |
| Ethernet Interfaces | Up to 4 x Gigabit Ethernet (SGMII / RGMII) |
| PCI Express | 2 x PCI Express interfaces |
| PCI-X | 1 x PCI-X controller |
| Serial RapidIO | 2 x Serial RapidIO endpoints |
| Security Engine | SEC 3.3 (AES, 3DES, SHA, public-key) |
| Local Bus | 8/16/32-bit, supports NAND flash |
| Junction Temperature Range | 0 C to +105 C |
| Silicon Revision | R3.0 |
| RoHS 状态 | Compliant (lead-free FCPBGA) |
MPC8547EVTAUJD 783-ball fcpbga, 29 mm x 29 mm 引脚配置指南
MPC8547EVTAUJD（783-ball fcpbga, 29 mm x 29 mm 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MPC8547EVTAUJD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MPC8547EVTAUJD 适用于 6 应用s: Multi-Service Routers and Edge Gateways, Wireless Base Station Baseband Controllers, Storage Controllers and NAS Heads, Industrial Automation Controllers, Telecom Line Cards and Aggregation Switches, Military and Aerospace Signal Processing.
Multi-Service Routers and Edge Gateways
The MPC8547EVTAUJD fits multi-service edge routers because it integrates four Gigabit Ethernet MACs with SGMII/RGMII support, two PCI Express ports, a PCI-X controller, and the SEC 3.3 crypto engine on a single die running at up to 1.333 GHz. A typical line card uses one MPC8547E as the control-plane processor, with the dual 64-bit DDR2 ECC controllers sustaining routing-table lookups and forwarding-table aging. The hardware-accelerated AES, 3DES, and SHA engines sustain IPSec and MACsec at line rate without burdening the e500 core, which is critical when the router must also handle OSPF, BGP, and traffic-policing workloads.
推荐
Wireless Base Station Baseband Controllers
Base transceiver station (BTS) controllers benefit from the MPC8547EVTAUJD's combination of two Serial RapidIO endpoints and four Gigabit Ethernet MACs, which can fan out DSP clusters, RF cards, and backhaul links from a single chip. The SEC 3.3 engine handles air-interface ciphering and authentication (Kasumi, Snow3G, AES) at full rate, offloading the e500 to manage Layer 2 framing, timing, and synchronization across CPRI/OBSAI fabrics. The ECC-protected DDR2 controllers meet telco reliability targets for outdoor base-station cabinets that must run continuously across decades.
推荐
Storage Controllers and NAS Heads
Network-attached storage (NAS) heads and RAID controllers deploy the MPC8547EVTAUJD to provide file-system acceleration in conjunction with PCI-X / PCI Express attached SATA or SAS controllers. The dual 64-bit DDR2 ECC controllers support large read-ahead caches, while the four Gigabit Ethernet ports handle link aggregation and 802.3ad bonding to upstream switches. The local bus with 8/16/32-bit data width and dedicated NAND flash support enables boot from a small NAND device alongside a larger NOR firmware store for field-upgradable appliances.
推荐
Industrial Automation Controllers
Industrial control platforms with deterministic networking - PROFINET, EtherNet/IP, and CC-Link IE - adopt the MPC8547EVTAUJD for its hardened real-time Ethernet MACs, hardware security for OPC-UA authentication, and rugged 0-105 C junction range. The processor's high-throughput DMA paths offload deterministic packet stamping to dedicated channels, leaving the e500 core to run the real-time control loop. Up to four Gigabit Ethernet ports feed redundant ring topologies common in plant-floor switches and machine vision hubs.
推荐
Telecom Line Cards and Aggregation Switches
Aggregation line cards in central offices use the MPC8547EVTAUJD to combine subscriber-side Ethernet, TDM-over-packet, and DSL/GPON traffic for uplink to metro switches. The PCI-X controller connects to legacy ASICs and DSPs, while the PCI Express interfaces link to modern FPGAs for traffic management offload. The hardware SEC 3.3 engine accelerates bulk encryption for trunk protection and MACsec interconnects, while the e500 core runs QoS queues, shaping, and policing without breaking jitter budgets.
推荐
Military and Aerospace Signal Processing
Ruggedized signal processing subsystems embed the MPC8547EVTAUJD for sensor fusion, electronic-countermeasures (ECM) front-ends, and tactical data links that require hardware-accelerated cryptography. The dual DDR2 ECC controllers protect mission data integrity against SEU-induced bit flips in avionics or surveillance platforms, while the Serial RapidIO endpoints fan out FPGA pre-processors via a low-latency deterministic fabric. The hardware SEC engine accelerates Suite B algorithms vital for tactical radios and beyond line-of-sight (BLOS) waveforms.
推荐
推荐产品汇总
工程参考数据： MPC8547EVTAUJD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MPC8547EVTAULJD | MPC8548EVTAQGD | MPC8548EVTAVJD |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 783-FCPBGA (29x29 mm) | 783-FCPBGA (29x29 mm) | 783-FCPBGA (29x29 mm) | 783-FCPBGA (29x29 mm) |
| Core Architecture | e500 / e500v2 single-core | e500 / e500v2 single-core | e500v2 single-core | e500v2 single-core |
| Maximum Core Frequency | 1.333 GHz | 1.0 GHz (-25%) | 1.0 GHz (-25%) | 1.5 GHz (+13%) |
| Memory Controllers | Dual 64-bit DDR2 + ECC | Dual 64-bit DDR2 + ECC | Dual 64-bit DDR2 + ECC | Dual 64-bit DDR2 + ECC |
| Gigabit Ethernet Ports | Up to 4 (SGMII/RGMII) | Up to 4 | Up to 4 | Up to 4 |
| PCI Express Interfaces | 2 x PCIe | 2 x PCIe | 2 x PCIe | 2 x PCIe |
| Security Engine | SEC 3.3 | SEC 3.3 | SEC 3.3 | SEC 3.3 |
| Junction Temperature Range | 0 C to +105 C | 0 C to +105 C | 0 C to +105 C | 0 C to +105 C |
| Drop-In Substitution Tier | Reference (1.333 GHz AJD) | Lower-power speed grade (-25%) | Step-up to MPC8548E feature set | Higher-speed (+13%) boost for headroom |
关键差异点
- Highest 1.333 GHz speed bin in the MPC8547E family (AJD suffix) （对比 MPC8547EVTAULJD)
- Same silicon infrastructure as MPC8548E for software reuse （对比 MPC8548EVTAQGD)
- Commercial 0-105 C temperature bin aligns with carrier-grade CO deployments （对比 Industrial-spec MPC85xx variants)
设计说明
Estimated: The 783-ball FCPBGA at 0.8 mm pitch in a 29 mm x 29 mm body mandates a microvia PCB stack-up with 8-12 layers, a continuous ground reference plane, and matched-length SERDES routing for SGMII, Serial RapidIO, and PCI Express lanes. Place 0.1 uF decoupling capacitors at every VDD and VDD I/O ball, with bulk ceramics at each voltage domain; target less than 100 mil trace lengths between the ball pad and the nearest decoupling capacitor to suppress switching noise.
Estimated: At 1.333 GHz with all four Ethernet MACs, both PCIe lanes, and the DDR2 controllers active, the MPC8547EVTAUJD can dissipate approximately 5-8 W depending on workload. The exposed thermal lid on the FCPBGA requires a heatsink or cold plate with thermal interface material, and the PCB should include 1 oz copper pours directly under the BGA to wick heat laterally before it reaches the lid. For sealed outdoor enclosures, derate the junction temperature to stay below the 105 C upper limit with a 25-30 C margin.
Power sequencing must follow the NXP MPC8547E datasheet sequence: bring up core, then DDR I/O, then peripheral I/O voltage rails with monotonic ramps. Latch-up can occur if the SERDES rails come up before the core voltage stabilizes. Also, do not route PCI Express or Serial RapidIO lanes across plane splits; the impedance discontinuity causes link training failures at 2.5 Gbps or higher. Use pre-emphasis and transmit de-emphasis settings in the SERDES configuration registers only as a last resort - mismatched PCB stack-up is the usual root cause.
合规信息
RoHS lead-free FCPBGA per NXP product page. Not AEC-Q100 qualified (automotive part numbers carry a separate prefix). All variants comply with EU REACH.
