MPXD1010VLU64 - 32-Bit 64MHz 1MB Flash MCU | NXP
料号： MPXD1010VLU64 ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $19.1413 | $19.14 |
| 10 | $18.5 | $185.00 |
| 100 | $16.8 | $1,680.00 |
| 500 | $14.95 | $7,475.00 |
| 1,000 | $13.6 | $13,600.00 |
MPXD1010VLU64 概述
A microcontroller is a programmable system-on-chip that executes firmware, manages digital inputs and outputs, and coordinates memories, communication interfaces, timers, and other peripherals. The e200z0h core places the MPXD1010VLU64 in the 32-bit embedded-controller segment, where deterministic control and communication throughput are more important than the power profile of a low-cost 8-bit device.
The verified specifications identify 1 MB (1M x 8) program flash, 48 KB (48K x 8) RAM, a 64 MHz operating frequency, 133 I/O pins, and connectivity including CANbus, I²C, LINbus, SCI, SPI, and UART/USART. The listed peripheral set also includes DMA, LCD, power-on reset, PWM, and a watchdog timer, supporting display controllers, automotive or industrial communications, and general embedded control systems.
The package is a 176-LQFP in a 24 mm x 24 mm gull-wing format. Its large pin count exposes substantially more signal and peripheral resources than a small microcontroller package, which is useful for systems combining display interfaces, external memory, communication buses, and control signals. The exact electrical limits, memory map, pin names, and timing values should be confirmed in the manufacturer datasheet before layout or firmware release.
Typical applications include entry-level display systems, industrial control panels, communication gateways, CAN-based equipment, and embedded systems requiring multiple serial interfaces. Because lifecycle information is reported as obsolete in one verified source, engineers should verify current sourcing, supported revisions, and any approved migration path before new production designs.
A key design consideration is to match the MCU's power, clock, peripheral, and package requirements to the existing PCB. The 176-LQFP footprint has fine-pitch leads and requires careful routing, thermal planning, and assembly inspection; do not substitute a different package without a documented footprint and pinout comparison.
This page consolidates the verified distributor specifications, lifecycle warning, package details, and replacement limitations for engineers evaluating the MPXD1010VLU64. Because the available cross-reference results do not verify five genuine same-package pin-to-pin alternatives, this page does not invent drop-in replacements.
直接替换替代料： MPXD1010VLU64 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MPXD1010VLU64 （相同外形与封装尺寸） ——差异在于 Package, Product Type.
快速对比工具——选择替代料号进行并排对比：
LPC4357JBD208E
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →MPXD1010VLU64 最大额定值与电气特性
| Product Type | 32-bit Microcontroller |
| Core Processor | e200z0h |
| Core Size | 32-bit |
| Operating Frequency | 64 MHz |
| Program Memory Size | 1 MB (1M x 8) |
| Program Memory Type | Flash |
| RAM Size | 48 KB (48K x 8) |
| Number of I/O | 133 |
| Connectivity | CANbus, I²C, LINbus, SCI, SPI, UART/USART |
| Peripherals | DMA, LCD, POR, PWM, WDT |
| 封装 | 176-LQFP |
| Package Dimensions | 24 mm x 24 mm |
| Terminal Count | 176 |
| Terminal Form | Gull wing |
| Temperature Grade | Industrial |
| Part Status | Obsolete |
| Manufacturer | NXP Semiconductors |
MPXD1010VLU64 24 mm x 24 mm 引脚配置指南
MPXD1010VLU64（24 mm x 24 mm 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MPXD1010VLU64.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MPXD1010VLU64 适用于 6 应用s: Entry-Level Display Controller, Industrial Communication Gateway, CAN-Based Control Module, Human-Machine Interface Controller, Sensor and Actuator Network, Legacy Embedded Platform Maintenance.
Entry-Level Display Controller
The MPXD1010VLU64 is explicitly identified by the verified source as a microcontroller for entry-level display solutions. Its 64 MHz e200z0h core can execute display-control firmware while the listed LCD peripheral, DMA, PWM, and serial interfaces support local user-interface and communication functions. The 1 MB flash provides room for graphics, control, and communication software, while 48 KB RAM can support buffering and protocol state. Designers should verify LCD timing, memory mapping, pin multiplexing, and electrical limits in the datasheet before layout.
推荐
Industrial Communication Gateway
The listed CANbus, LINbus, SCI, SPI, UART/USART, and I²C connectivity makes the MPXD1010VLU64 appropriate for a communication gateway that bridges several embedded serial domains. Its 64 MHz core can manage protocol tasks, while the 176-LQFP package exposes 133 I/O pins for status, control, and peripheral connections. The design must still check protocol electrical levels, transceiver requirements, pin multiplexing, bus timing, and any isolation requirements before production.
推荐
CAN-Based Control Module
The MPXD1010VLU64's listed CANbus interface and industrial temperature grade make it a candidate for CAN-based industrial control equipment. The controller can combine network management with PWM outputs, watchdog supervision, and general-purpose digital I/O in one 176-LQFP device. Engineers should verify CAN operating-mode details, transceiver selection, termination, clock configuration, and fault behavior in the manufacturer documentation; the supplied snippets do not provide those electrical or timing values.
推荐
Human-Machine Interface Controller
The LCD interface, PWM capability, 133 I/O pins, and multiple serial interfaces support a compact human-machine interface that combines a display, buttons, indicators, and external communications. At 64 MHz, the MCU can coordinate display updates and input handling while UART/USART or SPI connects to a host, keypad, or sensor interface. Firmware planning should account for pin multiplexing, peripheral conflicts, display timing, and the fact that the obsolete lifecycle status requires supply-chain confirmation.
推荐
Sensor and Actuator Network
The I²C, SPI, UART/USART, SCI, PWM, and GPIO resources make the MPXD1010VLU64 suitable for centralized sensor acquisition and actuator control. It can connect local sensors, coordinate PWM-driven outputs, and use watchdog supervision while retaining substantial flash and RAM for protocol and application firmware. Actual implementation depends on pin assignment, I/O voltage levels, peripheral timing, power requirements, and communication standards that are not fully detailed in the supplied snippets.
推荐
Legacy Embedded Platform Maintenance
Because the verified source reports MPXD1010VLU64 as obsolete, the part remains relevant to maintenance and continuation of installed industrial or display equipment. Its known 1 MB flash, 48 KB RAM, 64 MHz core, and 176-LQFP footprint allow engineers to identify compatible boards, reproduce firmware behavior, and plan controlled substitutions. A replacement must be validated against the original schematic, pinout, memory map, peripherals, clocking, software, and lifecycle requirements rather than selected by package number alone.
推荐
推荐产品汇总
工程参考数据： MPXD1010VLU64 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LPC4357JBD208E |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
关键差异点
- e200z0h 32-bit core with 64 MHz operation （对比 LPC4357JBD208E)
- 1 MB flash and 48 KB RAM （对比 LPC4357JBD208E)
- 176-LQFP with 133 I/O （对比 LPC4357JBD208E)
- Integrated display and vehicle-network peripherals （对比 LPC4357JBD208E)
设计说明
Use the current NXP 176-LQFP land pattern and package drawing as the authoritative PCB footprint. The verified source confirms a 24 mm x 24 mm gull-wing package but does not provide pad dimensions, so do not infer geometry from the package name. Check pin numbering, exposed thermal requirements if any, assembly clearance, and courtyard against the official mechanical drawing before releasing artwork.
The supplied data does not specify supply voltage, current, or power dissipation. Before connecting the MCU, determine the supported voltage range and all I/O domains from the manufacturer datasheet. Separate core, digital I/O, and any external interface supplies according to the verified power architecture, and do not infer a replacement power tree from the processor frequency or memory size.
The 176-LQFP device exposes 133 I/O pins and supports multiple communication interfaces. Plan pin multiplexing early so CANbus, LINbus, SPI, UART/USART, I²C, PWM, LCD, and debug functions do not conflict. Route high-speed or noise-sensitive interfaces away from switching nodes, preserve ground-return continuity, and validate every assigned signal against the datasheet pin table.
Do not treat obsolete status as proof that the existing part is unavailable, or distributor inventory as proof of long-term supply. Obtain manufacturer-approved lifecycle information, request date-code and traceability details, and validate any replacement for boot behavior, memory map, peripheral multiplexing, interrupt vectors, and software compatibility. A same-package candidate without complete pin and electrical validation is not a drop-in replacement.
Operating frequency and core type alone do not determine junction temperature or allowable board dissipation. Calculate thermal performance from the verified supply voltage, operating current, ambient temperature, package thermal resistance, PCB copper, and airflow. Those inputs are absent from the supplied data, so perform the calculation only after retrieving the manufacturer electrical and thermal specifications.
合规信息
The supplied verified snippets identify an industrial temperature grade and obsolete part status but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.
