MSP430F448IPZR - 8MHz 16-Bit MCU with 48KB Flash | TI
料号: MSP430F448IPZR ✓ 量产中MSP430F448IPZR 概述
An MSP430 mixed-signal microcontroller combines a low-power RISC processor with analog and communication peripherals on a single integrated circuit. The MSP430 family belongs to the broader embedded-controller hierarchy, where flash-programmable microcontrollers provide programmable control, data acquisition, and serial communication for compact electronic products. Its architecture emphasizes efficient execution, multiple low-power operating states, and deterministic peripheral interaction for battery-powered and portable measurement systems.
The principal features of the MSP430F448IPZR include an 8 MHz maximum clock, 48 KB flash, 2 KB SRAM, a 12-bit analog-to-digital converter, an analog comparator, SPI and UART connectivity, and a 160-segment LCD driver. Flash memory supports firmware and constants, while SRAM provides working memory for acquisition and control routines. The integrated mixed-signal peripherals reduce the number of external components needed for sensor measurement, local display, and communication.
The MSP430 architecture uses a 16-bit RISC CPU with 16-bit registers. Its low-power design is particularly useful in portable measurement products where duty-cycled operation can extend battery life. Peripherals are integrated for direct sensor interfacing, while the LCD driver allows local status or measurement display without another display controller. The manufacturer describes the MSP430 family as being optimized for extended battery life in portable measurement applications.
Typical uses include portable environmental monitors, industrial panel meters, handheld test instruments, connected sensor nodes, and low-power data-acquisition equipment. The 12-bit ADC supports analog measurement, the comparator handles threshold detection, SPI permits attachment to higher-bandwidth sensors or memory, UART supports simple host communication, and the LCD driver is useful in local-display instruments that need to operate without a continuous graphics processor.
PCB design should preserve the MSP430's low-noise analog performance by routing ADC inputs away from switching nodes and keeping supply and ground paths stable. Decoupling capacitors should be placed close to the relevant power pins, and the analog ground and digital ground strategy should follow the device's recommended layout guidance. Firmware should also use the documented low-power modes and avoid unnecessary polling so that the MCU spends more time in its lowest-energy states.
This product page combines the manufacturer's device characteristics, ordering information, technical features, application guidance, pin-package details, and carefully qualified replacement analysis. It is intended to help engineers evaluate clock speed, memory, analog conversion resolution, communication interfaces, LCD capability, power behavior, package compatibility, and sourcing requirements before finalizing an embedded design.
直接替换替代料: MSP430F448IPZR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MSP430F435IPZR
✅ 直接替换📋 参考替代料(不在目录中)
MSP430F448IPZR 最大额定值与电气特性
| Product Type | 16-bit mixed-signal microcontroller |
| 最大时钟频率 | 8 MHz |
| CPU Architecture | 16-bit RISC |
| Register Width | 16 bit |
| Flash Memory | 48 KB |
| Flash Organization | 48K x 8 plus 256 bytes |
| SRAM | 2 KB |
| ADC Resolution | 12 bit |
| ADC Count | 2 |
| Comparator | 1 |
| USART Count | 2 |
| SPI Interface | 1 |
| LCD Segment Capacity | 160 segments |
| Supply Voltage Range | 1.8 V to 3.6 V |
| Active Current at 1 MHz and 2.2 V | 280 uA |
| Standby Current | 1.1 uA |
| Off Current with RAM Retention | 0.1 uA |
| Wake-Up Time from Standby | Less than 6 us |
| Low-Power Modes | 5 |
| 封装 | 100-pin LQFP (PZ), 14 mm x 14 mm |
| 工作温度范围 | -40°C to 85°C |
| 安装类型 | Surface mount |
MSP430F448IPZR 100-pin lqfp (pz), 14 mm x 14 mm 引脚配置指南
MSP430F448IPZR(100-pin lqfp (pz), 14 mm x 14 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: MSP430F448IPZR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MSP430F448IPZR 适用于 6 应用s: Portable Environmental Monitor, Industrial Panel Meter, Battery-Powered Data Logger, Handheld Test Instrument, Connected Sensor Node, Local-Display Control Module.
Portable Environmental Monitor
The MSP430F448IPZR fits portable environmental monitors because its 8 MHz 16-bit RISC core can process sensor readings while its five low-power modes limit energy use between measurements. The 12-bit ADC supports analog sensor acquisition, while 48 KB of flash and 2 KB of SRAM provide room for acquisition logic, calibration data, and control functions. A duty-cycled design can use the documented 1.1 uA standby current and less-than-6-us wake-up time to reduce the energy cost of periodic readings.
推荐
Industrial Panel Meter
The MSP430F448IPZR is suitable for an industrial panel meter because its integrated 160-segment LCD driver can present measurement status without requiring a separate display controller. The 12-bit ADC provides higher conversion resolution than an 8-bit converter for scaled sensor inputs, and the 1.8 V to 3.6 V operating range supports compact low-voltage instrumentation. Firmware can combine display updates with periodic wake-up operation to reduce power when readings remain stable.
推荐
Battery-Powered Data Logger
The MSP430F448IPZR works well in a battery-powered data logger because the 0.1 uA off current with RAM retention and 1.1 uA standby current support long inactive intervals between samples. Its 48 KB flash stores firmware and logged metadata, while the 2 KB SRAM handles active acquisition buffers. The SPI and UART interfaces allow a memory or host connection, and the 280-uA active figure at 1 MHz provides a useful baseline for duty-cycle energy estimates.
推荐
Handheld Test Instrument
The MSP430F448IPZR supports handheld test instruments by combining measurement, communication, and local-display functions in one mixed-signal MCU. A 12-bit ADC can acquire analog test signals, the comparator can implement fast threshold detection, and SPI or the two USARTs can connect probes, sensors, or a host. The 100-pin LQFP footprint exposes the full peripheral set, while the low-power modes improve runtime between operator-triggered measurements.
推荐
Connected Sensor Node
The MSP430F448IPZR fits a connected sensor node that must acquire analog data and communicate intermittently with a controller. SPI provides a deterministic interface to sensors or external storage, while UART supports a simple host or radio connection. The MCU's 8 MHz clock and 16-bit architecture support local filtering and threshold logic without continuous high-power operation. Its 1.8 V to 3.6 V range allows the design to share a low-voltage rail when all connected peripherals support it.
推荐
Local-Display Control Module
The MSP430F448IPZR is appropriate for a dedicated local-display control module because the 160-segment LCD driver can manage segmented indicators or a simple character-oriented display. The remaining mixed-signal peripherals allow the same device to read a sensor, evaluate a comparator threshold, and update the display. Because the display driver is integrated, a board can avoid adding a separate LCD controller, provided the required segment count and electrical drive arrangement match the application.
推荐
工程参考数据: MSP430F448IPZR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MSP430F435IPZR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 100-pin LQFP (PZ), 14 mm x 14 mm | 100-pin LQFP (PZ) |
关键差异点
- Large integrated LCD segment capacity (对比 MSP430F435IPZR)
- Specific memory configuration for compact firmware (对比 MSP430F435IPZR)
- Integrated mixed-signal connectivity (对比 MSP430F435IPZR)
设计说明
Route the 12-bit ADC inputs away from switching nodes and keep their traces short to reduce coupling from adjacent digital signals. Follow the ADC channel grouping and reference arrangement shown in the Texas Instruments MSP430F448 datasheet when assigning the analog ground and supply pins.
Place the required bypass capacitors directly beside the associated VCC and ground pins, and use the minimum trace length recommended by the manufacturer. Because the documented supply range is 1.8 V to 3.6 V, verify startup, ADC accuracy, and peripheral limits at the lowest voltage used by the product.
Do not assume that an identical 100-pin package guarantees a drop-in replacement. Compare LCD outputs, ADC channels, comparator connections, serial-interface pins, reset behavior, and supply pins between the MSP430F448 and the candidate MSP430F435 before modifying an existing PCB or reusing firmware.
Use the documented low-power modes only after confirming which RAM contents, clocks, and peripherals remain active. Wake-up time is less than 6 us, but frequent short measurement cycles can still dominate energy use; calculate duty-cycle consumption from the 280-uA active and 1.1-uA standby figures together with sensor and display loads.
Preserve a quiet return path for the ADC and avoid routing LCD or communication signals beneath sensitive analog inputs where practical. Keep crystal, timing, and high-current output paths separated from analog inputs to minimize deterministic coupling rather than relying only on filtering after conversion.
合规信息
The available manufacturer and distributor product information does not explicitly state the requested compliance outcomes. Confirm current RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals documentation with Texas Instruments before production release.