OPA196ID - 36V Rail-to-Rail Operational Amplifier | TI
料号: OPA196ID ✓ 量产中OPA196ID 概述
An operational amplifier is an integrated circuit that amplifies the difference between two input voltages. It is a fundamental building block in analog electronics, within the broader hierarchy of semiconductor devices and signal-conditioning ICs. Rail-to-rail input capability allows the amplifier to operate across nearly the complete input-voltage range of the supply, while rail-to-rail output capability helps preserve signal swing near the supply rails. Mux-friendly inputs are useful when multiple signals must be connected to an amplifier through switching or multiplexing networks.
The OPA196ID is identified by Texas Instruments as a 36 V, low-power, all-purpose amplifier. Its rail-to-rail architecture and low-voltage operation make it appropriate for systems powered from industrial supplies, split analog rails, laboratory instrumentation, and higher-voltage sensor interfaces. The single-amplifier configuration in an 8-pin SOIC package also simplifies board design when one signal path is sufficient and a compact, standard surface-mount footprint is preferred.
The OPAx196 family includes the OPA196 single amplifier, OPA2196 dual amplifier, and OPA4196 quad amplifier. The OPA196ID is the single-amplifier SOIC-8 orderable variant. Its 36 V supply rating provides additional headroom for applications whose signal amplitudes exceed the range of common low-voltage amplifiers, while its general-purpose positioning allows it to be used for both low- and higher-voltage analog signal chains.
Typical uses include precision current sensing, buffer and driver stages, sensor amplification, data acquisition, industrial process control, and low-frequency communications equipment. When using the device, verify common-mode range, output swing, input bias current, noise, and stability requirements for the selected gain and load against the manufacturer datasheet.
For a replacement or second-source decision, confirm the exact package, pin arrangement, supply rating, offset voltage, bandwidth, slew rate, input bias current, noise, output-current capability, and operating-temperature requirements. This page focuses on the OPA196ID single-amplifier 8-pin SOIC version and separates manufacturer-supported information from parameters that require design-level verification.
直接替换替代料: OPA196ID ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: OPA196ID (相同外形与封装尺寸) ——差异在于 Product Type.
OPA197IDR
✅ 直接替换📋 参考替代料(不在目录中)
OPA196ID 最大额定值与电气特性
| Product Type | Single operational amplifier |
| Manufacturer | Texas Instruments |
| 电源电压 | 36 V |
| Architecture | Rail-to-rail input and output |
| Input Type | Mux-friendly input |
| Number of Circuits | 1 |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Operating Class | General-purpose amplifier |
OPA196ID 8-pin soic 引脚配置指南
OPA196ID(8-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: OPA196ID.
请参阅 数据手册 以查看完整引脚配置。
典型应用
OPA196ID 适用于 6 应用s: Industrial Sensor Signal Conditioning, Data Acquisition Front End, Precision Current and Voltage Measurement, Test and Measurement Instrumentation, Communications and Audio Buffering, Muxed Multichannel Measurement System.
Industrial Sensor Signal Conditioning
OPA196ID is appropriate for amplifying low-level sensor signals when the design operates from a relatively high-voltage analog rail. Its 36 V supply classification and rail-to-rail input and output architecture provide useful headroom for sensors whose output range approaches the supply limits. Place the amplifier in an inverting or non-inverting topology, keep the feedback network close to the device, and verify the actual common-mode range, input offset, noise, and output swing in the OPAx196 datasheet. The mux-friendly input architecture can also be useful when several sensor signals are routed through a multiplexer before amplification.
推荐
Data Acquisition Front End
OPA196ID can serve as the analog gain stage immediately before an ADC or data-conversion system. Its 36 V operating class and rail-to-rail behavior are useful in measurement equipment that accepts signals above the common range of low-voltage amplifiers, while the single-amplifier package leaves board space for additional channels. Design the feedback ratio around the required gain and bandwidth, confirm the output swing at the selected load, and check whether the amplifier's noise and offset meet the acquisition budget. A unity-gain buffer configuration is also possible when the source impedance and settling requirements permit it.
推荐
Precision Current and Voltage Measurement
OPA196ID is suitable for precision current or voltage measurement paths where the sensed signal must be amplified accurately within a wider-voltage system. The 36 V supply rating helps isolate the amplifier from the high-voltage portion of the circuit, while rail-to-rail operation can improve signal utilization when the input remains within the specified common-mode limits. In current-shunt measurements, pay particular attention to input offset voltage, bias current, noise, and the voltage drop across the shunt. For high-voltage front ends, add appropriate protection and isolation before applying the signal to the amplifier.
推荐
Test and Measurement Instrumentation
OPA196ID can be used in general-purpose laboratory and test instrumentation where a single precision amplifier must operate across a broader voltage range than conventional 5 V devices. Its rail-to-rail input and output characteristics are valuable for conditioning bipolar or near-rail signals, and the 8-pin SOIC package is convenient for compact analog boards. The design must account for the amplifier's actual input and output limits, offset drift, noise, bandwidth, and output-current capability. Stable feedback-network layout and short feedback traces are important when the circuit operates at higher gain or drives resistive and capacitive loads.
推荐
Communications and Audio Buffering
OPA196ID is suitable for buffering or modest gain stages in communications and audio equipment where low-level analog signals require amplification before conversion or transmission. Rail-to-rail operation can preserve dynamic range in single-supply designs, while the 36 V rating supports higher-voltage analog sections. The actual signal bandwidth and distortion must be checked against the OPAx196 datasheet, especially when the amplifier drives a cable, transformer, or capacitive load. Use short, direct routing for the input and feedback components and place any required output isolation resistor close to the amplifier to reduce unwanted capacitive feedback.
推荐
Muxed Multichannel Measurement System
OPA196ID is a logical candidate for a multiplexed measurement system because Texas Instruments specifically identifies its inputs as mux-friendly. Multiple sensor or test channels can be selected by an analog multiplexer and then amplified by the OPA196ID, reducing the number of separate amplifier packages while preserving a high-voltage-capable analog front end. Confirm that the multiplexer output remains within the amplifier's common-mode range and that source impedance does not create unacceptable settling behavior. The acquisition cycle must also allow the amplifier to settle to the required accuracy before the converted value is accepted.
推荐
推荐产品汇总
工程参考数据: OPA196ID ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | OPA197IDR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | SOIC-8 |
关键差异点
- Higher supply-voltage class (对比 OPA197IDR)
- Mux-friendly input architecture (对比 OPA197IDR)
- General-purpose 36 V rail-to-rail operation (对比 OPA197IDR)
设计说明
The OPA196ID is rated for a 36 V supply class, but the complete minimum and maximum operating supply limits must be checked in the manufacturer datasheet for the selected temperature grade. Derating the circuit for transient supply excursions, motor buses, and hot-plug events is important because the absolute maximum ratings are not operating targets. Confirm that the signal source, input protection network, and feedback components remain within their own voltage ratings.
Route the non-inverting input, feedback components, and ground return using short paths, and keep the feedback network close to the amplifier. For a precision circuit, use a continuous ground plane rather than a split plane unless the system architecture specifically requires isolation. Place input protection components close to the connector and keep their capacitance and leakage consistent with the required source impedance and bandwidth.
Do not assume that a 36 V amplifier automatically accepts any signal between the supply rails. Verify the OPA196ID common-mode input range, output swing, input protection behavior, and stability with the intended load. Rail-to-rail operation also has transition regions and load-dependent limits, so use the manufacturer data for the exact operating condition. When replacing OPA196ID with OPA197IDR, compare those same electrical limits rather than relying on the shared SOIC-8 outline.
For high-gain or wide-bandwidth signal-conditioning stages, minimize parasitic capacitance around the input and feedback nodes and use appropriately shielded or guarded routing for very high-impedance sources. The mux-friendly input characteristic does not remove the need to control source impedance and settling time. Check acquisition timing against the amplifier's small-signal and large-signal behavior before using the OPA196ID behind a multiplexer.
合规信息
The available manufacturer snippets identify the OPA196 as a 36 V, low-power, rail-to-rail amplifier but do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes on the current manufacturer product page or product declaration.