OPA2677N - Dual 220 MHz High-Current Amplifier | TI
料号: OPA2677N ✓ 量产中OPA2677N 概述
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to set gain accurately. The OPA2677 belongs to the current-feedback amplifier family, a topology well suited to high-speed, wideband signal chains where conventional voltage-feedback amplifiers may show gain-bandwidth and stability trade-offs.
Key features include unity-gain stability, a 10 uA input bias current, 5.5 mV input offset voltage, and low-distortion output stages capable of sourcing approximately 500 mA. According to the Texas Instruments product page, the OPA2677 consumes 9 mA per channel from a single +12 V supply while supporting more than 380 mA minimum output current, making it suitable for demanding xDSL customer-premises equipment and power-line modem drivers.
The current-feedback architecture preserves bandwidth across many closed-loop gain settings and supports rapid large-signal transitions. Its 2000 V/us slew rate reduces distortion when driving capacitive or resistive loads, while the high-current output stage avoids the load limitations associated with conventional precision operational amplifiers. Designers must still account for loop gain, trace resistance, output stability, and thermal dissipation when operating near the output-current limit.
Typical applications include ADSL and VDSL line-driver outputs, power-line communication modem drivers, instrumentation, wideband signal conditioning, and high-current buffer stages. The dual configuration allows two independent amplifier channels in one package, simplifying routing and reducing the component count in communications equipment.
A critical design practice is to keep feedback traces short and symmetrical, terminate unused channels according to the manufacturer recommendations, and provide local supply bypassing. Output-current capability does not guarantee unlimited drive into arbitrary loads; source impedance, load capacitance, supply voltage, and package thermal performance must be evaluated together.
This page combines the manufacturer’s electrical positioning with package, pricing, lifecycle, replacement, and application guidance. It also distinguishes a verified drop-in replacement from package-only or function-only alternatives, helping engineers avoid substitutions that change pinout, feedback behavior, supply requirements, or output-current capability.
直接替换替代料: OPA2677N ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料OPA2677N 最大额定值与电气特性
| Amplifier Type | Dual current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 220 MHz |
| Slew Rate | 2000 V/us |
| Input Bias Current | 10 uA |
| Input Offset Voltage | 5.5 mV |
| Supply Operation | +12 V |
| 静态电流 | 9 mA/channel |
| 最大输出电流 | 500 mA |
| Minimum Output Current | greater than 380 mA at +25 C |
| Gain Stability | Unity-gain stable |
| 封装 | 14-pin SOIC |
| 安装类型 | Surface mount |
| RoHS 状态 | Compliant |
| Primary Application | DSL and PLC line-driver output |
| Amplifier Class | SpeedPlus wideband high-output-current operational amplifier |
OPA2677N 14-pin soic 引脚配置指南
OPA2677N(14-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: OPA2677N.
请参阅 数据手册 以查看完整引脚配置。
典型应用
OPA2677N 适用于 6 应用s: ADSL and VDSL Line Drivers, Power-Line Communication Drivers, High-Current Buffer Stage, Wideband Instrumentation, Audio and Communication Output Amplification, Industrial Test Signal Generation.
ADSL and VDSL Line Drivers
The OPA2677N fits DSL line-driver output stages that require both wideband signal handling and substantial current drive. Its 220 MHz gain-bandwidth product, 2000 V/us slew rate, and approximately 500 mA output-current capability allow the amplifier to reproduce high-speed line waveforms while driving downstream transformer, network, or termination networks. According to the Texas Instruments product page, the device supports more than 380 mA minimum output current at +25 C from a single +12 V supply. The design must account for transformer loading, board parasitics, feedback-loop stability, and thermal rise under continuous transmission.
推荐
Power-Line Communication Drivers
The OPA2677N is suited to PLC modem output stages where the line interface must combine bandwidth with current capability. A 220 MHz gain-bandwidth product supports high-frequency signal content, while the 2000 V/us slew rate limits large-signal transition distortion. Its high-current output stage can deliver approximately 500 mA, helping the transmitter develop voltage across the intended network load. Designers should keep feedback components close to the device, evaluate output stability with the actual line transformer and cable capacitance, and verify thermal performance during sustained transmission.
推荐
High-Current Buffer Stage
OPA2677N can serve as a high-current buffer when the driven node is too demanding for a conventional precision operational amplifier. Unity-gain stability permits direct use as a non-inverting buffer, while approximately 500 mA output capability and 2000 V/us slew rate improve drive into resistive and capacitive loads. The 14-pin SOIC package contains two channels, allowing one section to buffer while the other handles a complementary signal. Confirm the load’s DC and AC current, watch the output-voltage swing, and provide adequate copper area for heat dissipation.
推荐
Wideband Instrumentation
The OPA2677N is appropriate for instrumentation stages that must preserve high-frequency content and drive moderate loads rather than merely amplify nanoampere-level sensor signals. Its 220 MHz bandwidth and 2000 V/us slew rate provide ample dynamic capability for waveform conditioning, while the dual current-feedback architecture supports independent inverting and non-inverting channels. Stable feedback design remains essential because current-feedback amplifiers can become unstable with excessive feedback resistance or excess parasitic capacitance. Use short, direct feedback traces and verify the complete gain network against the manufacturer’s stability guidance.
推荐
Audio and Communication Output Amplification
OPA2677N can amplify communication and line-level signals when the output stage must deliver considerably more current than a conventional small-signal amplifier. The high-current output stage provides useful headroom for balanced line outputs, termination networks, and communication interfaces, while the 220 MHz bandwidth preserves fast edges. The trade-off is higher power consumption and a need for careful grounding because the wideband, high-current stage can reveal supply-impedance and layout problems. Bypass each supply pin locally and keep feedback and output routing compact to minimize oscillation and distortion risks.
推荐
Industrial Test Signal Generation
OPA2677N is useful in industrial test equipment that generates or buffers fast signals into moderately demanding loads. Its 2000 V/us slew rate supports rapid edge reproduction, and approximately 500 mA output capability provides more drive than a standard precision amplifier. The device can therefore buffer DAC outputs, excite limited sensor networks, or drive test fixtures while maintaining bandwidth. Design around the actual fixture capacitance because excessive load capacitance can perturb the output stage, and validate both output-current and temperature rise over long test cycles.
推荐
推荐产品汇总
工程参考数据: OPA2677N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 14-pin SOIC |
| Brand | Texas Instruments |
| Amplifier Architecture | Dual current-feedback operational amplifier |
| Gain-Bandwidth Product | 220 MHz |
| Slew Rate | 2000 V/us |
| Output Current | Approximately 500 mA |
| Quiescent Current | 9 mA/channel |
| Input Bias Current | 10 uA |
| Input Offset Voltage | 5.5 mV |
| Supply Configuration | Single +12 V |
关键差异点
- Substantially higher output-current capability than conventional precision amplifiers (对比 OPA2677T)
- High-speed current-feedback operation in a dual 14-pin SOIC (对比 OPA2677N/2K5)
- Purpose-built combination of bandwidth, slew rate, and drive current (对比 Generic precision operational amplifier)
设计说明
Keep the feedback network, input connections, and output routing compact because current-feedback amplifiers can become unstable when large parasitic capacitance appears inside the feedback loop. Place input and feedback components close to their associated pins, use short ground returns, and avoid routing the output directly beneath sensitive input nodes. Confirm that the complete feedback network remains stable at the intended closed-loop gain and load.
Design the +12 V supply path for both signal fidelity and output-current demand. Place short, low-inductance bypass capacitors from each supply pin to the appropriate ground plane, and provide an additional local reservoir capacitor where the load can draw approximately 500 mA. Check the source impedance at the amplifier pins because supply noise and supply droop can reduce output headroom and increase distortion during large-signal operation.
Estimate output dissipation from the actual output voltage, load current, and supply voltage rather than treating the 500 mA rating as a continuously usable operating point. Use the 14-pin SOIC land pattern and surrounding PCB copper to lower junction temperature, while keeping exposed lead and pad geometry consistent with the manufacturer’s package drawing. Recheck the output-current limit at the highest expected ambient temperature and during sustained transmission.
Do not substitute a generic precision amplifier, a lower-current line driver, or a different package on the assumption that similar bandwidth is sufficient. Current-feedback behavior, supply rails, output swing, output-current capability, and pin assignment all affect interchangeability. Confirm that unused channels are terminated as directed in the manufacturer documentation and verify the output stage against the actual resistive and capacitive load.
合规信息
RoHS compliance is stated in the OPA2677N distributor listing. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was established for this exact orderable part.