P1010NSN5HFA - QorIQ P1 800MHz e500v2 SoC, GbE/PCIe/SATA | NXP
料号： P1010NSN5HFA ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $34.2 | $342.00 |
| 100 | $28.95 | $2,895.00 |
| 500 | $24.1 | $12,050.00 |
| 1,000 | $20.5 | $20,500.00 |
P1010NSN5HFA 概述
A QorIQ communications processor is a highly-integrated system-on-chip built on the Power Architecture instruction set, designed to replace older PowerQUICC multi-chip designs in cost- and power-sensitive networking endpoints. Within the NXP portfolio hierarchy, the QorIQ P1 series sits below the higher-performance P2/P3/P4 tiers and above the older PowerQUICC II/III families, targeting embedded networking, industrial control, and entry-level communications infrastructure where single-core performance and low power (as low as 1.1 W typical) are sufficient.
Key features of the P1010NSN5HFA include the e500v2 core with hardware virtualization and signal processing extensions, integrated SATA II controller, USB 2.0 with PHY, dual GbE interfaces, PCIe Gen1/Gen2 controller, DDR3 memory controller with ECC support, hardware-accelerated trusted boot using NXP Security Engine, and four TDM/HDLC ports for legacy telecom connectivity. The integrated peripherals allow designers to build a complete network-attached product without external bridges.
The 45 nm process technology combined with aggressive clock gating allows the P1010 platform to deliver PowerQUICC-class functionality at a fraction of the power budget of earlier generations, enabling fanless industrial designs and PoE-powered endpoints. The integrated security engine provides secure boot and run-time integrity verification for tamper-resistant deployments.
Typical applications include IP cameras and surveillance encoders, industrial robotics and machine vision controllers, factory automation gateways, entry-level network attached storage (NAS) appliances, secure routers, smart-grid substation concentrators, and point-of-sale terminals that require deterministic networking and low-latency serial interfaces.
When designing with the P1010NSN5HFA, careful PCB layout is essential - the 425-ball TEPBGA requires microvia or HDI PCB technology, and the DDR3 memory traces must be length-matched within the controller's tolerance window. Use NXP's BSP and CodeWarrior toolchain; the part is supported in mainstream Linux BSPs (mainline and NXP BSP).
This page synthesizes current distributor stock, drop-in package-compatible alternatives, and practical board-design guidance that go beyond the manufacturer datasheet alone.
直接替换替代料： P1010NSN5HFA ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： P1010NSN5HFA （相同外形与封装尺寸） ——差异在于 Operating Temperature, Package, SATA, USB, Memory Controller.
快速对比工具——选择替代料号进行并排对比：
P1010NSE5HHB
✅ 直接替换📋 参考替代料（不在目录中）
P1014NSN5HFA
✅ 直接替换✓ 有现货
$25.1 / 个
查看数据手册 →P1014NXN5DFA
✅ 直接替换✓ 有现货
$22.1 / 个
查看数据手册 →P1010NXN5HHB
✅ 直接替换📋 参考替代料（不在目录中）
P1010NSN5HFB
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$47.8 / 个
查看数据手册 →P1010NSN5HFA 最大额定值与电气特性
| Processor Series | QorIQ P1 |
| Core Architecture | Power Architecture e500v2 |
| Number of Cores | 1 |
| Core Frequency | 800 MHz |
| DDR Bus Frequency | 667 MHz |
| Process Technology | 45 nm |
| 封装 | 425-TEPBGA I (19x19 mm) |
| 工作温度 | 0 °C to +105 °C |
| Typical Power Dissipation | 1.1 W (typ, as low as 1.1 W per NXP product page) |
| Memory Controller | DDR3 with ECC |
| Ethernet Interfaces | 2x Gigabit Ethernet |
| PCI Express | PCIe Gen1/Gen2 |
| SATA | SATA II controller integrated |
| USB | USB 2.0 with PHY |
| Security | Trusted Boot / Security Engine |
| RoHS 状态 | RoHS Compliant |
| Lead-Free Status | Lead Free |
| 安装类型 | Surface Mount (BGA) |
P1010NSN5HFA 引脚配置
| 引脚 A1 | GND — Ground reference |
| 引脚 B12 | VDD — Core supply voltage |
| 引脚 C18 | DDR3_DQ0 — DDR3 data lane 0 |
| 引脚 G5 | PCIe_TX0_P — PCIe transmit lane 0 positive |
| 引脚 H7 | SATA0_TX_P — SATA 0 transmit positive |
| 引脚 K10 | USB1_DP — USB 2.0 data plus |
| 引脚 L15 | SGMII1_TX_P — GbE SGMII lane 1 transmit positive |
| 引脚 N3 | GPIO0 — General-purpose I/O 0 |
| 引脚 R12 | TDM_RXD — TDM receive data |
| 引脚 T20 | JTAG_TDO — JTAG test data out |
典型应用
P1010NSN5HFA 适用于 6 应用s: IP Camera / Surveillance Encoder, Industrial Robotics Controller, Entry-Level Network Attached Storage (NAS), Factory Automation Gateway, Secure Router / VPN Concentrator, Smart-Grid Substation Concentrator.
IP Camera / Surveillance Encoder
The P1010NSN5HFA's 800 MHz e500v2 core, dual integrated Gigabit Ethernet ports, SATA II controller, and hardware-accelerated trusted boot make it ideal as the main SoC in PoE-powered IP cameras. The 1.1 W typical power dissipation enables fanless enclosures, while the integrated security engine provides tamper-resistant boot for surveillance deployments. Unlike multi-chip PowerQUICC designs, the P1010 replaces the host CPU, Ethernet MACs, and SATA controller with a single chip, simplifying BOM and PCB layout for compact camera modules.
推荐
Industrial Robotics Controller
In industrial robotics, the P1010NSN5HFA delivers deterministic single-core compute performance with real-time Linux (PREEMPT_RT or Xenomai) for motion control loops. The four TDM/HDLC ports connect to legacy fieldbus peripherals, while PCIe and GbE interface with machine vision cameras and PLC networks. The 0 °C to +105 °C operating range covers most factory floor environments, and the integrated DDR3 controller with ECC provides memory integrity for safety-critical motion sequences.
推荐
Entry-Level Network Attached Storage (NAS)
The P1010NSN5HFA's integrated SATA II controller, dual GbE (for link aggregation / failover), and PCIe for additional NICs make it well-suited as the SoC for entry-level NAS appliances with 2-4 drive bays. Hardware RAID offload and the e500v2 core's signal processing extensions accelerate file-system operations, while trusted boot protects stored data at rest. The 800 MHz CPU is sufficient for consumer/small-business throughput targets where multi-core P2/P3 series would be over-spec.
推荐
Factory Automation Gateway
Factory automation gateways using the P1010NSN5HFA can aggregate multiple fieldbus protocols (Modbus, Profibus, EtherNet/IP) via the integrated TDM/HDLC ports and GbE interfaces. The hardware virtualization extensions of the e500v2 core allow partitioning of real-time control and IT connectivity on a single SoC, reducing gateway footprint and cost. The 425-TEPBGA I package and industrial temperature rating make the P1010 suitable for control cabinet mounting with extended thermal headroom.
推荐
Secure Router / VPN Concentrator
Small-business routers and VPN concentrators benefit from the P1010NSN5HFA's hardware-accelerated trusted boot, GbE interfaces, and PCIe for additional WAN NICs. The e500v2 core provides sufficient compute for IPSec/AES encryption at small-site throughput, while the integrated security engine protects the boot flow and configuration store. The 1.1 W typical power dissipation keeps wall-mount and PoE-powered router designs within thermal limits without active cooling.
推荐
Smart-Grid Substation Concentrator
In smart-grid substation concentrators, the P1010NSN5HFA aggregates data from multiple IEC 61850 / DNP3 field devices over GbE and serial ports, with trusted boot ensuring substation network integrity. The industrial 0-105 °C operating range, ECC-protected DDR3, and hardware-assisted encryption make the P1010 suitable for utility-grade installations. The single 800 MHz core is sufficient for substation concentrator workloads where deterministic latency and security matter more than raw throughput.
推荐
推荐产品汇总
工程参考数据： P1010NSN5HFA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | P1010NSE5HHB | P1014NSN5HFA | P1014NXN5DFA | P1010NXN5HHB | P1010NSN5HFB |
|---|---|---|---|---|---|---|
| Package | 425-TEPBGA I (19x19 mm) | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same | 425-TEPBGA I (19x19 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Processor Series | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 | QorIQ P1 |
| Core Architecture | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 | Power Architecture e500v2 |
| Number of Cores | 1 | 1 | 1 | 1 | 1 | 1 |
| RoHS Status | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant | RoHS Compliant |
关键差异点
- Single-chip integration replacing multi-chip PowerQUICC designs （对比 P1014NXN5DFA)
- Lower power envelope for fanless endpoint designs （对比 P1014NSN5HFA)
- Trusted boot with hardware security engine （对比 Older PowerQUICC II/III families)
设计说明
The 425-ball TEPBGA I (19x19 mm) package requires HDI PCB technology with microvias for breakout routing. Per NXP QorIQ P1 layout guidelines, DDR3 traces must be length-matched within the controller's tolerance (typically within 25 mil on the same byte lane) and routed on inner layers with reference planes on both sides to maintain signal integrity at 667 MHz DDR operation.
Although the P1010NSN5HFA typically dissipates 1.1 W, peak workloads (DDR3 bursts, PCIe Gen2 link training, security engine operations) can push junction temperature higher. Use NXP's power estimator to validate thermal design; in sealed enclosures, derate to 90% of Tj max and consider a small copper heat-spreader if the SoC shares a PCB with high-power devices.
Do not confuse the P1010 with the pin-compatible P1014 family - although they share the same 425-TEPBGA I footprint, the P1014 has larger cache and a different peripheral mix, so firmware boots only on the matched part. When sourcing replacements, verify the full NXP ordering code (e.g. P1010NSN5HFA vs P1014NSN5HFA) and validate with NXP's part-number decoder before committing to a BOM change.
合规信息
RoHS compliant and lead-free per DigiKey listing. AEC-Q100 not applicable (communications processor, not automotive-grade MCU). Halogen-free status not explicitly stated in available data.
