PCA9518DBT - 5-Channel I2C Hub | Texas Instruments
料号: PCA9518DBT ✓ 量产中PCA9518DBT 概述
An I2C hub is an interface IC that divides one upstream serial bus into multiple downstream branches. The PCA9518 belongs to the broader I2C buffer and bus-interface hierarchy, where bidirectional level translation is combined with bus-segmentation functions. Its open-drain architecture preserves the wired-AND behavior used by I2C and SMBus, while the buffered branches isolate capacitive loading among groups of downstream devices. Each SDA and SCL path is buffered bidirectionally so the hub can support normal transfers as well as clock stretching where supported by the connected devices.
The principal feature is expandability through five downstream channels. A single hub can fan one upstream I2C bus into five branches, and additional hubs can extend the hierarchy when a design requires more branches. The supported operating range of 3 V to 3.6 V suits conventional low-voltage embedded systems, while the 400 kHz operating rate accommodates fast-mode I2C communication. The open-drain buffers use pull-up resistors to establish the high level, so resistor sizing must account for the voltage, capacitance, sink current, and rise-time requirements of each branch.
The PCA9518DBT uses a BiCMOS integrated-circuit implementation containing five multidirectional open-drain buffer pairs. The design allows standard low-level contention arbitration, preserves the electrical behavior expected from I2C, and separates upstream and downstream bus capacitance. Unlike a passive isolator or a unidirectional level shifter, the device supports two-way communication through every buffered branch. It also avoids the load-sharing limitations that arise when multiple devices are connected directly to one long, highly capacitive bus.
Typical uses include industrial embedded-control systems, sensor aggregation, data-acquisition equipment, communications modules, programmable-instrumentation platforms, and compact computer systems with several low-speed peripheral buses. The hub is particularly useful where a processor must communicate with sensor groups, memory devices, or expansion boards distributed across a PCB. Each branch should remain below the 400 pF capacitance limit, and pull-up placement should follow the topology of the upstream and downstream segments rather than being concentrated indiscriminately on one node.
A key design consideration is validating every supported operating mode with the complete bus network, including pull-up values, cable or PCB capacitance, clock-stretching behavior, and arbitration. The device does not remove the need for correct I2C rise time or for assigning unique addresses to connected peripherals. Use the manufacturer pin-description table and application information when assigning tracks and validating the 20-pin SSOP footprint.
This product overview consolidates the device function, electrical boundaries, package details, application guidance, and design considerations into an engineering-focused reference. It also identifies where package or bus-topology differences can prevent an apparent substitute from serving as a true drop-in replacement.
直接替换替代料: PCA9518DBT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PCA9518DBT (相同外形与封装尺寸) ——差异在于 Package, Product Type, Supply Voltage Range.
PCA9518PW
✅ 直接替换联系询价
查看数据手册 →PCA9518AD,112
✅ 直接替换📋 参考替代料(不在目录中)
PCA9518APW,518
✅ 直接替换📋 参考替代料(不在目录中)
PCA9518DBT 规格参数
| Product Type | Expandable five-channel bidirectional I2C/SMBus buffer and hub |
| Number of Channels | 5 channels |
| Supply Voltage Range | 3 V to 3.6 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Per-Bus Capacitance Limit | 400 pF |
| Buffer Direction | Bidirectional |
| 输出配置 | Open-drain |
| Process Technology | BiCMOS |
| Protocol Support | I2C and SMBus |
| 封装 | 20-pin SSOP, 5.30 mm width |
| Package Width | 5.30 mm |
| Package Width in Inches | 0.209 inch |
| 安装类型 | Surface mount |
| 引脚数量 | 20 pins |
PCA9518DBT 0.209 inch 引脚配置指南
PCA9518DBT(0.209 inch 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9518DBT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9518DBT 适用于 6 应用s: Industrial Sensor Aggregation, Data Acquisition Systems, Programmable Instrumentation, Communications Equipment, Compact Embedded Systems, Smart Home and Sensor Networks.
Industrial Sensor Aggregation
The PCA9518DBT fits industrial sensor boards that must connect multiple sensor groups to a single embedded I2C controller. Its five downstream channels divide the network into groups that can each remain within the 400 pF I2C capacitance limit, while the 3 V to 3.6 V supply range suits common embedded rails. Place the hub near the point where the bus branches and calculate pull-up resistance separately for each branch. The 400 kHz limit must remain compatible with every sensor's timing, and the complete industrial temperature range must be verified before deployment.
推荐
Data Acquisition Systems
The PCA9518DBT is useful in data-acquisition equipment where converters, amplifiers, and conditioning electronics are distributed across a board or connected through short cable assemblies. Five bidirectional branches reduce the capacitive load presented to the controller and can isolate separate peripheral groups behind the 400 pF limit. The hub supports I2C and SMBus traffic up to 400 kHz, but cable length, connector capacitance, pull-up placement, and rise time must be evaluated together. The BiCMOS open-drain implementation preserves the arbitration and clock-stretching behavior expected by the bus.
推荐
Programmable Instrumentation
In programmable instrumentation, the PCA9518DBT can connect a low-voltage controller to groups of measurement peripherals, interface controllers, and configuration registers. Bidirectional buffering supports ordinary reads and writes while allowing each downstream group to remain below the 400 pF bus-capacitance limit. The five-channel architecture also offers a practical path for expanding the bus beyond a single board or module boundary. Designers should calculate rise time at the worst-case capacitance and verify that no peripheral stretches SCL beyond the timing allowed by the 400 kHz operating specification.
推荐
Communications Equipment
The PCA9518DBT fits communications modules that expose configuration, status, and management interfaces through I2C or SMBus. Its five channels can organize management peripherals into separate downstream groups, reducing the capacitance presented to a communications processor and helping maintain the 400 pF limit for each group. The device operates from 3 V to 3.6 V and supports bidirectional transfers up to 400 kHz. Pull-ups should be selected for the actual branch voltage and load, and the design must confirm that arbitration and clock stretching remain compliant across every connected device.
推荐
Compact Embedded Systems
The PCA9518DBT is appropriate for compact embedded systems in which one controller must communicate with memory, sensors, display interfaces, and expansion modules over a common low-voltage bus. Rather than placing all devices on one long capacitive segment, the engineer can assign related peripherals to separate branches. The 20-pin SSOP provides a surface-mount implementation, and the 3 V to 3.6 V operating range fits many embedded rails. Unique device addresses remain mandatory, and total branch capacitance, pull-up current, bus rise time, and timing margins must be validated together.
推荐
Smart Home and Sensor Networks
The PCA9518DBT can organize multiple smart-home sensor groups, configuration devices, and low-power controllers on a common I2C backbone. Its five downstream branches help separate capacitive loads and preserve the 400 pF limit for each branch while supporting two-way register access at up to 400 kHz. The 3 V to 3.6 V supply range fits many low-voltage sensor nodes. For battery-powered endpoints, evaluate the complete system's idle behavior separately, verify the hub's operating temperature range, and use pull-up networks that preserve an acceptable logic-high rise time.
推荐
推荐产品汇总
工程参考数据: PCA9518DBT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 20-pin SSOP |
| Brand | Texas Instruments |
| Number of Channels | 5 channels |
| Supply Voltage Range | 3 V to 3.6 V |
| Maximum Bus Frequency | 400 kHz |
| Bus Capacitance per Group | 400 pF |
| Buffer Direction | Bidirectional |
| Output Configuration | Open-drain |
| Supported Protocols | I2C and SMBus |
关键差异点
- Five individually buffered downstream groups (对比 PCA9548ADBR)
- Direct fit for low-voltage I2C and SMBus systems (对比 PCA9518PW)
- Bidirectional open-drain branch isolation (对比 Direct I2C connection)
设计说明
Place the PCA9518DBT near the physical branch point of the I2C network, and route each downstream branch as a separate bus segment. Keep each branch at or below 400 pF after including PCB traces, connectors, cable capacitance, and device input capacitance. Position pull-up resistors on the relevant upstream or downstream segment rather than placing every resistor at the hub. This arrangement minimizes residual loading on the controller and makes rise-time troubleshooting easier.
Calculate each SDA and SCL pull-up from the actual logic voltage, branch capacitance, sink-current limit, and required rise time. Faster operation requires a lower pull-up resistance, but that increases the current drawn during a low assertion and can exceed the sink-current capability of a connected device. Check the slow end with maximum capacitance and the fast end with the largest pull-up resistance allowed by timing. Include probe and connector capacitance in the worst-case calculation.
Do not treat a five-channel hub as an address translator or as an automatic cure for an over-capacity bus. Every downstream peripheral still requires a unique I2C address, and each branch must independently satisfy its capacitance and timing limits. Also avoid assuming that a 20-pin package with the same pin count is PCB-compatible: the SSOP lead geometry, body width, and pinout must match exactly before a substitute is approved.
Decouple the PCA9518DBT supply close to the device and keep the ground return compact, because open-drain bus transitions and branch pull-up currents create fast transient currents in the PCB. Follow the manufacturer guidance for supply and ground-pin connections and bypass capacitance. Analyze the resulting reference-current path over the same ground plane used by the I2C devices so switching and bus edges do not introduce unintended voltage offsets between communicating devices.
合规信息
Use the manufacturer product page and current material-declaration records for definitive environmental and automotive qualification status.