Texas Instruments

PCA9518DBT - 5-Channel I2C Hub | Texas Instruments

MPN: PCA9518DBT ✓ فعال
3 V to 3.6 V Vdss 20-pin SSOP, 5.30 mm width Package 400 kHz Speed
MOQ: 1 |

PCA9518DBT جائزہ

Texas Instruments PCA9518DBT is an expandable five-channel bidirectional I2C and SMBus buffer/hub operating from 3 V to 3.6 V at up to 400 kHz. The device is packaged in a 20-pin SSOP measuring approximately 5.30 mm wide. Its five buffered channels divide a capacitive I2C bus into groups that can each remain within the 400 pF bus-capacitance limit. The PCA9518DBT is therefore useful when system-level bus loading, wiring length, or the number of connected devices makes a single undivided I2C segment impractical.

An I2C hub is an interface IC that divides one upstream serial bus into multiple downstream branches. The PCA9518 belongs to the broader I2C buffer and bus-interface hierarchy, where bidirectional level translation is combined with bus-segmentation functions. Its open-drain architecture preserves the wired-AND behavior used by I2C and SMBus, while the buffered branches isolate capacitive loading among groups of downstream devices. Each SDA and SCL path is buffered bidirectionally so the hub can support normal transfers as well as clock stretching where supported by the connected devices.

The principal feature is expandability through five downstream channels. A single hub can fan one upstream I2C bus into five branches, and additional hubs can extend the hierarchy when a design requires more branches. The supported operating range of 3 V to 3.6 V suits conventional low-voltage embedded systems, while the 400 kHz operating rate accommodates fast-mode I2C communication. The open-drain buffers use pull-up resistors to establish the high level, so resistor sizing must account for the voltage, capacitance, sink current, and rise-time requirements of each branch.

The PCA9518DBT uses a BiCMOS integrated-circuit implementation containing five multidirectional open-drain buffer pairs. The design allows standard low-level contention arbitration, preserves the electrical behavior expected from I2C, and separates upstream and downstream bus capacitance. Unlike a passive isolator or a unidirectional level shifter, the device supports two-way communication through every buffered branch. It also avoids the load-sharing limitations that arise when multiple devices are connected directly to one long, highly capacitive bus.

Typical uses include industrial embedded-control systems, sensor aggregation, data-acquisition equipment, communications modules, programmable-instrumentation platforms, and compact computer systems with several low-speed peripheral buses. The hub is particularly useful where a processor must communicate with sensor groups, memory devices, or expansion boards distributed across a PCB. Each branch should remain below the 400 pF capacitance limit, and pull-up placement should follow the topology of the upstream and downstream segments rather than being concentrated indiscriminately on one node.

A key design consideration is validating every supported operating mode with the complete bus network, including pull-up values, cable or PCB capacitance, clock-stretching behavior, and arbitration. The device does not remove the need for correct I2C rise time or for assigning unique addresses to connected peripherals. Use the manufacturer pin-description table and application information when assigning tracks and validating the 20-pin SSOP footprint.

This product overview consolidates the device function, electrical boundaries, package details, application guidance, and design considerations into an engineering-focused reference. It also identifies where package or bus-topology differences can prevent an apparent substitute from serving as a true drop-in replacement.

کے لیے ڈراپ اِن متبادل PCA9518DBT — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PCA9518DBT (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Product Type, Supply Voltage Range.

NXP Semiconductors
Package: 20-pin TSSOP
Product Type: Expandable 5-channel I2C-bus hub
Supply Voltage Range: 2.3 V to 3.6 V
موازنہ کریں PCA9518DBT →

PCA9518PW

✅ ڈراپ-اِن
NXP Semiconductors
📦 20-TSSOP (PW)
Expandable 5-channel I2C-bus hub · I2C and SMBus · BiCMOS · 2.3 V to 3.6 V · 5 channels · 400 kHz · VDD below 2.0 V · I2C-bus I/O pins remain high impedance

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

PCA9518AD,112

✅ ڈراپ-اِن
📦 20-SSOP (AD)
Identical 5-channel 400 kHz bidirectional I2C/SMBus buffer function with the same 20-SSOP body; no enable-pin or supply-range difference identified

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

PCA9518APW,518

✅ ڈراپ-اِن
📦 20-TSSOP (APW)
Same 5-channel 400 kHz I2C/SMBus buffer hub in a 20-TSSOP body; matches the PCA9518PW footprint rather than the 5.30 mm SSOP body of PCA9518DBT

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

PCA9518DBT تفصیلات

Product Type Expandable five-channel bidirectional I2C/SMBus buffer and hub
Number of Channels 5 channels
Supply Voltage Range 3 V to 3.6 V
Maximum I2C Bus Frequency 400 kHz
Per-Bus Capacitance Limit 400 pF
Buffer Direction Bidirectional
آؤٹ پٹ کنفیگریشن Open-drain
Process Technology BiCMOS
Protocol Support I2C and SMBus
پیکیج 20-pin SSOP, 5.30 mm width
Package Width 5.30 mm
Package Width in Inches 0.209 inch
ماؤنٹنگ ٹائپ Surface mount
پن کی تعداد 20 pins

PCA9518DBT 0.209 inch پن کنفیگریشن گائیڈ

PCA9518DBT (0.209 inch پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

PCA9518DBT کے لیے 0.209 inch پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں PCA9518DBT.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

PCA9518DBT کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sensor Aggregation, Data Acquisition Systems, Programmable Instrumentation, Communications Equipment, Compact Embedded Systems, Smart Home and Sensor Networks.

🏭

Industrial Sensor Aggregation

The PCA9518DBT fits industrial sensor boards that must connect multiple sensor groups to a single embedded I2C controller. Its five downstream channels divide the network into groups that can each remain within the 400 pF I2C capacitance limit, while the 3 V to 3.6 V supply range suits common embedded rails. Place the hub near the point where the bus branches and calculate pull-up resistance separately for each branch. The 400 kHz limit must remain compatible with every sensor's timing, and the complete industrial temperature range must be verified before deployment.

📊

Data Acquisition Systems

The PCA9518DBT is useful in data-acquisition equipment where converters, amplifiers, and conditioning electronics are distributed across a board or connected through short cable assemblies. Five bidirectional branches reduce the capacitive load presented to the controller and can isolate separate peripheral groups behind the 400 pF limit. The hub supports I2C and SMBus traffic up to 400 kHz, but cable length, connector capacitance, pull-up placement, and rise time must be evaluated together. The BiCMOS open-drain implementation preserves the arbitration and clock-stretching behavior expected by the bus.

🔧

Programmable Instrumentation

In programmable instrumentation, the PCA9518DBT can connect a low-voltage controller to groups of measurement peripherals, interface controllers, and configuration registers. Bidirectional buffering supports ordinary reads and writes while allowing each downstream group to remain below the 400 pF bus-capacitance limit. The five-channel architecture also offers a practical path for expanding the bus beyond a single board or module boundary. Designers should calculate rise time at the worst-case capacitance and verify that no peripheral stretches SCL beyond the timing allowed by the 400 kHz operating specification.

🌐

Communications Equipment

The PCA9518DBT fits communications modules that expose configuration, status, and management interfaces through I2C or SMBus. Its five channels can organize management peripherals into separate downstream groups, reducing the capacitance presented to a communications processor and helping maintain the 400 pF limit for each group. The device operates from 3 V to 3.6 V and supports bidirectional transfers up to 400 kHz. Pull-ups should be selected for the actual branch voltage and load, and the design must confirm that arbitration and clock stretching remain compliant across every connected device.

🖥️

Compact Embedded Systems

The PCA9518DBT is appropriate for compact embedded systems in which one controller must communicate with memory, sensors, display interfaces, and expansion modules over a common low-voltage bus. Rather than placing all devices on one long capacitive segment, the engineer can assign related peripherals to separate branches. The 20-pin SSOP provides a surface-mount implementation, and the 3 V to 3.6 V operating range fits many embedded rails. Unique device addresses remain mandatory, and total branch capacitance, pull-up current, bus rise time, and timing margins must be validated together.

🧩

Smart Home and Sensor Networks

The PCA9518DBT can organize multiple smart-home sensor groups, configuration devices, and low-power controllers on a common I2C backbone. Its five downstream branches help separate capacitive loads and preserve the 400 pF limit for each branch while supporting two-way register access at up to 400 kHz. The 3 V to 3.6 V supply range fits many low-voltage sensor nodes. For battery-powered endpoints, evaluate the complete system's idle behavior separately, verify the hub's operating temperature range, and use pull-up networks that preserve an acceptable logic-high rise time.

What is the PCA9518DBT?
The PCA9518DBT is a Texas Instruments expandable five-channel bidirectional buffer for I2C and SMBus applications. According to the manufacturer product page, it operates from 3 V to 3.6 V, supports bus speeds up to 400 kHz, and separates a capacitive bus into multiple groups of up to 400 pF. Its five downstream channels make it useful when one upstream I2C controller must serve several separately buffered peripheral groups.
What are the key specifications of PCA9518DBT that engineers should know?
The PCA9518DBT is a 20-pin SSOP I2C/SMBus hub with five bidirectional channels, a 3 V to 3.6 V operating range, and a maximum bus frequency of 400 kHz. According to Texas Instruments, each buffered group is designed around the 400 pF I2C capacitance limit. The implementation is BiCMOS, the buffers are open-drain, and the device supports both normal bidirectional transfers and low-level contention arbitration characteristic of I2C.
How does the PCA9518DBT increase I2C bus capacity?
The PCA9518DBT increases usable bus capacity by buffering one upstream I2C segment into five downstream branches rather than connecting every device directly to one capacitive node. According to the manufacturer documentation, the branches are separated into groups that can each remain within the 400 pF limit. This reduces the capacitive loading seen by the upstream bus while preserving two-way SDA and SCL communication and open-drain bus behavior.
What is the difference between an I2C hub and an I2C multiplexer?
An I2C hub divides one upstream bus into several downstream branches, whereas a multiplexer usually selects one downstream branch at a time through control inputs. The PCA9518DBT is a five-channel hub: all branches can participate in bus transactions under normal I2C addressing rules. It buffers bus capacitance between channel groups, but it does not assign addresses or electrically isolate unrelated slave transactions.
Can the PCA9518DBT support 400 kHz I2C operation?
Yes, the PCA9518DBT supports I2C operation up to 400 kHz within its specified 3 V to 3.6 V supply range. According to the Texas Instruments product page, it is a 400 kHz I2C/SMBus buffer. Achieving the maximum rate still requires a correctly designed bus: pull-up resistance must satisfy the sink-current limit while producing an acceptable rise time, and each downstream segment must remain within the 400 pF capacitance limit.
What pull-up resistors does the PCA9518DBT require?
The PCA9518DBT requires pull-up resistors on its open-drain SDA and SCL nets because the buffers do not actively drive a logic-high level. Calculate each resistor using the bus voltage, target rise time, branch capacitance, and the sink-current capability of the connected devices. Keep the branch at or below 400 pF and verify rise time with the longest trace, connector, and device-loading condition rather than relying only on the bare PCB.
Where can I download the PCA9518DBT datasheet PDF?
The official PCA9518DBT datasheet is available through the Texas Instruments product page at https://www.ti.com/product/PCA9518 and the manufacturer datasheet link at https://www.ti.com/lit/gpn/PCA9518. The datasheet contains the authoritative pin descriptions, electrical characteristics, application circuit, and package outline. Use the manufacturer copy for design sign-off because distributor-hosted PDF copies may be older mirrors of the same document.
Where can I find the PCA9518DBT pinout?
The PCA9518DBT pinout is shown in the Texas Instruments datasheet under the pin configuration and pin-description tables for the 20-pin SSOP. The package has 20 pins, but the individual pin numbers and functions must be assigned from that table before PCB routing. Do not infer the SSOP footprint from the similarly named TSSOP variants because the package body and lead geometry may differ even when the pin count is the same.
What is the best drop-in replacement for PCA9518DBT?
No verified drop-in replacement is established for the PCA9518DBT in the available cross-reference results. A replacement is only drop-in if it uses the same 20-pin SSOP footprint, preserves pin-to-pin connections, supports the 3 V to 3.6 V range, and provides compatible 400 kHz bidirectional open-drain behavior. The listed PCA9518PW uses a different package designation, while PCA9548ADBR changes the channel count and package, so neither qualifies as a verified PCB drop-in.
Can PCA9518PW replace PCA9518DBT?
The PCA9518PW should not be treated as a verified drop-in replacement for the PCA9518DBT without a package-level footprint review. Both are 20-pin devices in the PCA9518 family, but the PW and DBT package suffixes denote different package constructions, and the search result does not establish identical lead dimensions, pinout, or board land pattern. It can serve as a function-level alternative only after checking the manufacturer package drawings and every connection.
Can PCA9548ADBR replace PCA9518DBT?
No, the PCA9548ADBR is not a pin-compatible replacement for the PCA9518DBT because the available comparison identifies a different package and channel configuration. The PCA9518DBT provides five downstream channels in a 20-pin SSOP, while PCA9548ADBR is associated with an eight-channel device in a 24-pin SSOP. It requires a PCB redesign and cannot be installed as a drop-in component.
When should I choose PCA9518DBT over a direct I2C connection?
Choose the PCA9518DBT when the calculated load on one I2C segment approaches the 400 pF limit, when long interconnects distribute bus capacitance, or when several peripheral groups need separate downstream branches. A direct connection remains preferable for short traces, low capacitance, and few devices because the hub adds cost, branching, pull-up design work, and another failure point. Use the hub when its capacitance-isolation benefit outweighs those system-level trade-offs.
Is PCA9518DBT suitable for sensor and industrial control systems?
The PCA9518DBT is suitable for sensor and industrial control systems that use low-voltage I2C or SMBus links and need multiple downstream branches. Its 3 V to 3.6 V supply range suits conventional embedded rails, and its 400 kHz capability supports fast-mode communication. The system still needs unique peripheral addresses, correctly selected pull-up resistors, branch capacitance below 400 pF, and validated behavior across the full industrial temperature range.
Where can I buy PCA9518DBT and check current stock and lead time?
Use the Request a Quote form on this page to request current PCA9518DBT pricing, stock status, minimum order quantity, and lead time. Quote requests keep commercial terms tied to the current supply position rather than embedding a stale price or availability claim. Include your required quantity, packaging preference, and target ship date so procurement can confirm the appropriate 20-pin SSOP supply configuration.
Does PCA9518DBT provide level shifting between 3.3 V and 5 V systems?
The PCA9518DBT is primarily a bus-segmentation and buffering device, not a general-purpose 3.3 V to 5 V bidirectional level translator. Its stated operating supply range is 3 V to 3.6 V, and its open-drain channels can support level translation only when the upstream and downstream pull-up networks use compatible logic levels. Confirm every connected device's absolute voltage limits and bus timing before using that behavior.

کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9518DBT — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the PCA9518DBT when a 3 V to 3.6 V system needs more I2C capacity than one 400 pF segment can provide and can justify a five-channel hub. It is especially useful when peripherals naturally divide into groups or when physical distance and connectors increase bus capacitance. A direct I2C connection is usually simpler and more efficient for short, lightly loaded boards. Do not select the PCA9518PW as a drop-in without checking its package drawing and pinout, and do not select the PCA9548ADBR when an unchanged PCB is required because its eight-channel, 24-pin design differs. Before releasing a design, verify branch capacitance, pull-up current, rise time, arbitration behavior, clock stretching, address allocation, and the operating temperature range of the complete interface network.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ
Package 20-pin SSOP
Brand Texas Instruments
Number of Channels 5 channels
Supply Voltage Range 3 V to 3.6 V
Maximum Bus Frequency 400 kHz
Bus Capacitance per Group 400 pF
Buffer Direction Bidirectional
Output Configuration Open-drain
Supported Protocols I2C and SMBus

اہم امتیازی خصوصیات

  • Five individually buffered downstream groups (بمقابلہPCA9548ADBR)
  • Direct fit for low-voltage I2C and SMBus systems (بمقابلہPCA9518PW)
  • Bidirectional open-drain branch isolation (بمقابلہDirect I2C connection)

ڈیزائن نوٹس

Place the PCA9518DBT near the physical branch point of the I2C network, and route each downstream branch as a separate bus segment. Keep each branch at or below 400 pF after including PCB traces, connectors, cable capacitance, and device input capacitance. Position pull-up resistors on the relevant upstream or downstream segment rather than placing every resistor at the hub. This arrangement minimizes residual loading on the controller and makes rise-time troubleshooting easier.

Calculate each SDA and SCL pull-up from the actual logic voltage, branch capacitance, sink-current limit, and required rise time. Faster operation requires a lower pull-up resistance, but that increases the current drawn during a low assertion and can exceed the sink-current capability of a connected device. Check the slow end with maximum capacitance and the fast end with the largest pull-up resistance allowed by timing. Include probe and connector capacitance in the worst-case calculation.

Do not treat a five-channel hub as an address translator or as an automatic cure for an over-capacity bus. Every downstream peripheral still requires a unique I2C address, and each branch must independently satisfy its capacitance and timing limits. Also avoid assuming that a 20-pin package with the same pin count is PCB-compatible: the SSOP lead geometry, body width, and pinout must match exactly before a substitute is approved.

Decouple the PCA9518DBT supply close to the device and keep the ground return compact, because open-drain bus transitions and branch pull-up currents create fast transient currents in the PCB. Follow the manufacturer guidance for supply and ground-pin connections and bypass capacitance. Analyze the resulting reference-current path over the same ground plane used by the I2C devices so switching and bus edges do not introduce unintended voltage offsets between communicating devices.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

Use the manufacturer product page and current material-declaration records for definitive environmental and automotive qualification status.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-10 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

PCA9518DBT datasheet PCA9518DBT pinout PCA9518DBT datasheet pdf PCA9518DBT 20-SSOP PCA9518DBT I2C hub PCA9518DBT 400 kHz PCA9518DBT 3.6 V Texas Instruments PCA9518DBT PCA9518DBT drop-in replacement PCA9518DBT vs PCA9518PW PCA9518DBT application circuit PCA9518DBT price PCA9518DBT stock where to buy PCA9518DBT

متعلقہ اجزاء اور اصطلاحات

Texas Instruments PCA9518DBT PCA9518 PCA9518PW PCA9548ADBR I2C hub I2C buffer SMBus buffer bidirectional buffer open-drain buffer I2C SMBus BiCMOS 400 kHz 400 pF 20-pin SSOP SSOP package surface mount SDA SCL clock stretching bus arbitration pull-up resistor 3 V to 3.6 V supply
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں