PCA9543APW 2-Channel I2C Switch with Interrupt and Reset | NXP
料号: PCA9543APW ✓ 量产中PCA9543APW 概述
An I2C switch, also called an I2C bus switch or multiplexer, is an interface IC that routes serial data and clock lines between one controller-side bus and multiple downstream ports. In the hierarchy of electronic components, an I2C switch belongs to the interface-controller category, then to the broader interface IC and logic IC families. Its purpose is to make multiple compatible I2C peripherals easier to interconnect on a shared two-wire bus while preserving electrical and protocol compatibility.
The PCA9543APW provides two switch channels, interrupt logic, and a reset function. Its 2.3 V to 5.5 V operating range supports both common low-voltage embedded systems and higher-voltage I2C environments. The TSSOP-14 surface-mount package is suitable for compact PCB layouts, while the interrupt and reset controls support systems requiring peripheral detection, fault recovery, or controlled power-up behavior. These characteristics make the device useful in embedded control, sensor networking, communications equipment, and general-purpose I2C expansion designs.
Architecturally, the PCA9543APW separates the upstream SDA and SCL path from the two downstream channels. Downstream ports can be enabled or isolated according to system requirements, reducing loading and helping prevent unintended communication with devices that share the same bus. The interrupt function provides a hardware indication of activity on a downstream channel, allowing the host controller to service only the relevant peripheral. The reset input provides a common mechanism for returning the switch to a defined operating state during system initialization or recovery.
Typical applications include I2C sensor aggregation, industrial monitoring modules, programmable power systems, communications equipment, and embedded controllers with multiple I2C peripherals. In a sensor-hub design, the upstream bus can remain connected while one downstream branch is isolated during reset or firmware updates. In a multi-domain instrument, the interrupt output can indicate that a downstream device has generated an event without requiring continuous polling of every branch.
A key design consideration is ensuring that the selected channel states match the intended bus topology. Review the manufacturer pin and connection information before assigning SDA, SCL, reset, interrupt, and enable functions. Account for pull-up resistor placement, bus capacitance, voltage levels, and the power-up relationship between the controller and downstream devices. These checks are essential because the device can simplify routing while still requiring correct bus-level implementation.
This product overview combines the manufacturer product information with practical design guidance, drop-in replacement context, pin and package details, and application-specific selection considerations. It is intended to help engineers evaluate the PCA9543APW for I2C bus isolation, voltage-level interfacing, and multi-peripheral system architectures without obscuring the important implementation trade-offs.
直接替换替代料: PCA9543APW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PCA9543APW
✅ 直接替换联系询价
查看数据手册 →TCA9543APWR
✅ 直接替换📋 参考替代料(不在目录中)
PCA9543APWRG4
✅ 直接替换📋 参考替代料(不在目录中)
PCA9543APW 最大额定值与电气特性
| Product Type | 2-channel I2C-bus switch |
| Number of Channels | 2 channels |
| Operating Supply Voltage Range | 2.3 V to 5.5 V |
| Interrupt Function | Yes |
| Reset Function | Yes |
| Voltage Translation | Supported |
| Package Type | TSSOP (PW) |
| 引脚数 | 14 pins |
| 工作温度范围 | -40 °C to +85 °C |
| 安装类型 | Surface mount |
| Bus Interface | I2C/SMBus |
| Upstream Ports | 1 |
| Downstream Ports | 2 |
| Maximum Power Dissipation | 400 mW |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
PCA9543APW tssop (pw) 引脚配置指南
PCA9543APW(tssop (pw) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9543APW.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9543APW 适用于 6 应用s: Industrial Sensor Aggregation, Embedded Communications Equipment, Programmable Power Control, Test and Measurement Front Ends, IoT Sensor Gateways, Multi-Sensor Monitoring Systems.
Industrial Sensor Aggregation
The PCA9543APW fits industrial sensor-aggregation boards that connect several I2C sensors to a single embedded controller. Its 2-channel architecture lets the host isolate one downstream branch while communicating with another, reducing unnecessary loading during diagnostics or firmware updates. The 2.3 V to 5.5 V operating range supports common industrial logic environments, while interrupt logic can identify activity on a monitored branch. Confirm pull-up values, bus capacitance, and channel state during the device’s 2.3 V to 5.5 V power-up sequence.
推荐
Embedded Communications Equipment
The PCA9543APW is useful in embedded communications equipment that connects address-based I2C transceivers, memory devices, or configuration peripherals to a host bus. Two selectable downstream channels help organize devices that require isolation during initialization or maintenance. Its interrupt output can prompt the controller to service a downstream event, and reset supports a deterministic startup state. The TSSOP-14 package also keeps routing compact, provided that trace lengths and pull-up placement meet the applicable I2C timing requirements.
推荐
Programmable Power Control
The PCA9543APW can organize I2C-controlled power-management peripherals in programmable power systems. Separate downstream channels allow the controller to isolate one group of converters or monitors while retaining access to another group. The 2.3 V to 5.5 V range covers common control-rail voltages, while reset and interrupt provide useful coordination points. Designers should verify that every downstream device remains compatible with the selected logic level and that channel isolation does not remove a device’s required pull-up path.
推荐
Test and Measurement Front Ends
The PCA9543APW can organize low-power I2C sensors and control registers in test and measurement front ends. A host instrument can select a downstream channel for configuration while keeping another channel isolated, reducing unintended communication between attached modules. Interrupt logic can indicate peripheral activity, and reset provides a common recovery mechanism. For high-speed or long-cable installations, evaluate capacitance, pull-up strength, and signal-integrity margins rather than assuming that logical compatibility guarantees reliable communication.
推荐
IoT Sensor Gateways
The PCA9543APW is appropriate for compact IoT sensor gateways that need to connect multiple I2C peripherals without allowing every device to remain active on the common bus. Its two channels support branch isolation, while the interrupt output can wake or direct host-controller attention toward a downstream event. The 14-pin TSSOP package supports space-constrained boards and the 2.3 V to 5.5 V range accommodates several embedded platforms. Validate standby behavior, pull-up placement, and power-domain sequencing before deploying the switch across independently switched domains.
推荐
Multi-Sensor Monitoring Systems
The PCA9543APW can support monitoring systems that combine several I2C sensing devices with a common host. Independent channel selection helps avoid simultaneous access to isolated branches and provides a controlled path for firmware recovery. The interrupt function is useful when a downstream sensor must request service, while reset establishes a known state after power changes. Check the master clock rate against total bus capacitance and ensure that disabled channels do not leave required pull-ups or powered devices in an undefined state.
推荐
推荐产品汇总
工程参考数据: PCA9543APW ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCA9543APW | TCA9543APWR | PCA9543APWRG4 |
|---|---|---|---|---|
| Brand | NXP Semiconductors | Texas Instruments | Texas Instruments | NXP Semiconductors |
| Package | TSSOP-14 (PW) | TSSOP-14 (PW) | TSSOP-14 (PW) | TSSOP-14 (PW) |
| Function | 2-channel I2C-bus switch | 2-channel 2.3 V to 5.5 V I2C/SMBus switch | 2-channel I2C switch | 2-channel I2C-bus switch |
| Channel Count | 2 channels | 2 channels | 2 channels | 2 channels |
关键差异点
- Direct same-package replacement identified by the manufacturer (对比 PCA9543APW from Texas Instruments)
- Channel topology matches the target without increasing port count (对比 PCA9544APW/G-T)
- Interrupt and reset functions are incorporated into the 14-pin device (对比 TCA9543APWR)
设计说明
Confirm that the upstream and downstream logic levels remain within the device’s 2.3 V to 5.5 V operating range and support the intended voltage-translation configuration. Place the required bus pull-up resistors at the correct physical locations so that disconnected or disabled branches do not impose an unintended voltage on a powered segment. Review reset behavior during power-up to prevent partial bus activity or contention between master and peripheral devices.
Route SDA and SCL from the upstream controller to the PCA9543APW and onward to each downstream branch with short, continuous traces. Keep pull-up components close to the devices that establish each voltage domain, and avoid long stubs on disabled channels. Review trace capacitance and pull-up strength against the intended I2C clock rate, especially when sensor cables or long PCB routes are present.
Do not approve a replacement using package appearance alone. Compare the complete pin descriptions, interrupt polarity, reset behavior, channel-enable logic, electrical thresholds, and timing characteristics. The documented TI PCA9543APW and TCA9543APWR are closest candidates, but each design must still verify that software control and external pull-up arrangements remain valid after substitution.
合规信息
The available product listings identify the device as active but do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These fields remain unknown rather than assumed.