PCA9546APW - 4-Channel I2C Switch with Reset | NXP
料号: PCA9546APW ✓ 量产中PCA9546APW 概述
An I2C-bus switch is an interface integrated circuit that routes clock and data lines between a controller and peripheral buses. Its role in the hierarchy is I2C interface switch, then bus interface IC, then interface IC, and finally semiconductor. Unlike a simple passive connection, this switch actively selects channels and provides bidirectional translation between upstream and downstream voltage domains. This makes it useful when several embedded devices or sensors must be connected to one I2C bus while maintaining individual enable control.
The PCA9546A family provides four independently selectable downstream channels and a control interface connected to the upstream bus. Its active-low reset input allows the switch to recover from a stuck bus condition by returning the control register to its default state. The 16-TSSOP package is intended for surface-mount PCB assembly. Operation requires correct I2C address handling, suitable pull-up placement, and verification of downstream logic levels against the device's electrical limits.
The switch supports communication with multiple downstream devices that use compatible I2C protocols and addresses. Channel selection is software-controlled through the programmable control register, so a host processor can enable only the required downstream bus at a particular time. This can reduce unnecessary bus activity and help prevent devices with the same fixed I2C address from responding simultaneously when they are connected to separate switched channels.
Typical uses include sensor aggregation, industrial measurement modules, programmable instrumentation, embedded control boards, and systems that connect several low-bandwidth peripheral buses to one microcontroller. It is also appropriate for prototype and production boards requiring more than one downstream I2C branch. The design should preserve the upstream bus, isolate each downstream branch with the intended pull-up network, and account for capacitance and propagation delay introduced by the additional switch and wiring.
A key implementation consideration is bus recovery. The active-low reset function can clear a channel-selection state when a downstream device holds SDA or SCL low, but designers should still provide a mechanism to cycle power or reset the affected peripheral. Validate address conflicts, logic thresholds, pull-up strength, and reset timing before using the switch with devices that operate at different voltage levels.
This page combines the manufacturer product information with practical guidance for channel routing, reset behavior, PCB implementation, and replacement analysis. It also distinguishes ordering-code variants from genuinely different functions so engineers can evaluate drop-in sourcing options without mistaking a packaging suffix for a functional upgrade.
直接替换替代料: PCA9546APW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PCA9546APW,118
✅ 直接替换📋 参考替代料(不在目录中)
PCA9546APWR
✅ 直接替换📋 参考替代料(不在目录中)
PCA9546APW 最大额定值与电气特性
| Device Type | 4-channel bidirectional I2C-bus switch |
| Number of Channels | 4 channels |
| Upstream Bus | 1 SCL/SDA pair |
| Downstream Buses | 4 SCL/SDA pairs |
| Interface Standard | I2C |
| Reset Input | Active-low |
| Control Method | Programmable control register |
| Data Direction | Bidirectional |
| 封装 | 16-pin TSSOP |
| 安装类型 | Surface mount |
PCA9546APW 16-pin tssop 引脚配置指南
PCA9546APW(16-pin tssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9546APW.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9546APW 适用于 6 应用s: Multi-Sensor Controller, Programmable Test and Measurement, Industrial Embedded Control, Connected Sensor Hub, I2C Address Conflict Isolation, Portable Instrumentation.
Multi-Sensor Controller
The PCA9546APW fits a controller board that connects several groups of I2C sensors to one host processor. Its four downstream SCL/SDA pairs let firmware enable only the branch associated with the active measurement, while the programmable control register can select individual channels or combinations. This arrangement also separates sensors that use fixed, identical addresses onto different branches. The design must keep each channel's pull-up network local, verify the total downstream capacitance, and confirm that every sensor operates within the switch's supported voltage and timing limits.
推荐
Programmable Test and Measurement
In programmable instrumentation, the PCA9546APW can route a common I2C controller toward up to four measurement channels. The host can select a channel or combination through the control register, reducing unnecessary communication with devices that are not being measured. The active-low reset input provides a controlled way to return the switch to its default state after a downstream bus fault. For accurate measurements, isolate each branch carefully, provide appropriate pull-ups, and validate the maximum operating clock against the slowest downstream peripheral and the added bus capacitance.
推荐
Industrial Embedded Control
The PCA9546APW is useful in industrial embedded-control boards that must connect several low-bandwidth I2C peripheral groups to a single processor interface. Four switchable downstream branches simplify routing when a system contains sensor boards, interface converters, or configuration devices with incompatible fixed addresses. The reset function helps the host recover the multiplexer after a peripheral holds the bus low, although the downstream device may also require a power cycle. Industrial designs should account for operating-temperature requirements, transient noise, grounding, pull-up placement, and cable or harness capacitance before release.
推荐
Connected Sensor Hub
A connected sensor hub can use the PCA9546APW to organize multiple downstream I2C sensor branches behind one upstream bus. Channel selection prevents idle branches from participating in communication and gives each device group an isolated path. This is especially helpful when several compact sensor modules use fixed addresses and cannot be reconfigured. Firmware should maintain a deterministic channel-selection sequence, avoid changing channels while a transfer is active, and use the reset input as part of a documented recovery procedure rather than as a substitute for correct peripheral power management.
推荐
I2C Address Conflict Isolation
The PCA9546APW addresses the common problem of several fixed-address I2C devices responding simultaneously on one bus. Each conflicting device is connected to a separate downstream channel, and the host enables one channel at a time during the associated transfer. This approach preserves the existing device firmware and avoids rewriting peripheral address logic. Because the channels share one upstream interface, the controller must complete each bus transaction before selecting another channel, and pull-ups must be placed so disabled branches do not create unintended signal paths or excessive loading.
推荐
Portable Instrumentation
Portable test and measurement equipment can use the PCA9546APW to connect a compact set of sensors or fixtures through one I2C port. The 16-pin TSSOP package supports board-level integration, while four selectable channels simplify expansion without adding a separate switch at the host controller. Runtime channel control can reduce communication overhead when only one fixture is active. Designers should keep traces short where possible, place pull-ups according to the selected bus topology, verify capacitive loading from attached leads, and confirm the device's electrical limits across the complete temperature range of the portable product.
推荐
推荐产品汇总
工程参考数据: PCA9546APW ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCA9546APW,118 | PCA9546APWR |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | Texas Instruments |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Device Type | 4-channel bidirectional I2C-bus switch | 4-channel I2C-bus switch | 4-channel I2C/SMBus switch |
| Number of Channels | 4 channels | 4 channels | 4 channels |
| Upstream Bus | 1 SCL/SDA pair | 1 SCL/SDA pair | 1 SCL/SDA pair |
| Downstream Buses | 4 SCL/SDA pairs | 4 SCL/SDA pairs | 4 SCL/SDA pairs |
| Reset Function | Active-low reset input | Reset function indicated by part family | Reset function indicated by part family |
| Control Interface | Programmable control register over I2C | Programmable control register | Programmable control register |
| Mounting Type | Surface mount | Surface mount | Surface mount |
关键差异点
- Same four-channel footprint and architecture (对比 PCA9546APWR)
- Manufacturer-specific ordering continuity (对比 PCA9546APWR)
- Programmable channel isolation (对比 PCA9546APW,118)
设计说明
Route each downstream SCL and SDA branch as a short, matched pair from the switch to its intended peripheral group. Keep pull-up placement consistent with the selected bus topology, and avoid long stubs from disabled channels that could increase capacitance or permit unintended signal coupling. Use a continuous ground plane beneath the TSSOP and minimize loop area around clock, data, and supply paths.
Do not change channel selection while an I2C transfer is in progress. Complete the current transaction, acknowledge or handle the peripheral response, and then issue the next control-register write. Also ensure the host does not address a disabled channel. A reset can clear the multiplexer state, but it does not necessarily reset a downstream peripheral that is holding SDA or SCL low.
Validate downstream capacitance, pull-up resistance, clock rate, and peripheral timing together. Each additional branch increases the amount of wiring and capacitance that the bus must drive. Compare the complete operating envelope with the manufacturer limits, and use the slowest downstream device when determining whether a shared clock rate is acceptable.
Decouple the switch close to its supply pins with the capacitance recommended by the manufacturer datasheet and provide a low-impedance ground return. Do not infer the allowable supply range from unrelated PCA95xx devices; confirm the exact PCA9546APW limits. Ensure the host and downstream peripherals use compatible logic levels or include appropriate level translation outside the switch.
合规信息
The verified product information does not state the requested compliance status. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals declarations with the manufacturer or the applicable product documentation.