PCA9605D - 400 kHz I2C Bus Buffer | NXP Semiconductors
料号: PCA9605D ✓ 量产中PCA9605D 概述
An I2C bus buffer is an interface IC that divides a two-wire serial bus into two segments and isolates their electrical loading. The PCA9605D allows each segment to operate within its permissible bus capacitance, extending the usable bus when long cables, multiple branches, or additional peripheral loading would otherwise burden the controller. In the device hierarchy, it belongs to the I2C interface-buffer family, bus buffers and repeaters, interface ICs, and integrated circuits.
The PCA9605D includes one buffered SDA channel and one buffered SCL channel. Operating voltage of 2.7 V to 5.5 V supports both 3.3 V and 5 V systems, while the 400 kHz maximum bus frequency covers standard- and fast-mode I2C communication. The monolithic CMOS implementation provides bidirectional signal buffering in an 8-pin SOIC package rated for industrial-temperature operation from -40 °C to +85 °C.
The buffered architecture reduces the capacitive load presented to the upstream bus controller by placing the source-side and load-side segments behind the buffer. This can improve bus signal integrity when a design contains multiple branches, connector segments, or distributed sensors. The device is intended for bus segmentation rather than level translation, so the source and destination domains should use compatible logic voltage levels.
Typical uses include industrial sensor networks, server-management buses, display-control interfaces, power-system PMBus connections, and embedded systems that divide I2C traffic across multiple PCB or cable segments. The buffer is also suitable for SMBus and DDC arrangements where the controller must communicate beyond the loading allowed by a direct bus connection.
PCB implementation requires correct pull-up placement and short, clean routing between the controller, buffer, and downstream devices. Place the input-side pull-ups near the active bus controller and the output-side pull-ups near the buffered load, then keep both SDA and SCL routes short and away from switching-node and high-current paths. Verify rise-time, fall-time, capacitance, and timing margins with the complete board configuration.
This product overview combines manufacturer application information, package and interface characteristics, commercial sourcing guidance, and practical PCB considerations for engineers evaluating the PCA9605D. Use the Request a Quote form on this page for current availability, lead time, and commercial terms.
直接替换替代料: PCA9605D ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PCA9600D,118
✅ 直接替换联系询价
查看数据手册 →PCA9605D 规格参数
| Device Type | Monolithic CMOS two-wire bus buffer |
| Supported Bus Protocols | I2C, SMBus, DDC, PMBus, and similar two-wire buses |
| Maximum I2C Bus Frequency | 400 kHz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Buffered Bus Channels | 1 two-wire channel |
| SDA Channels | 1 channel |
| SCL Channels | 1 channel |
| Input Lines | 1 |
| Output Lines | 1 |
| 工作温度范围 | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| Package Type | 8-pin SOIC |
| Package Code | SOP |
| Terminal Count | 8 terminals |
| Terminal Form | Gull wing |
| 安装类型 | Surface mount |
| Manufacturing Technology | CMOS |
PCA9605D sop 引脚配置指南
PCA9605D(sop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9605D.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9605D 适用于 6 应用s: Industrial Sensor Bus Segmentation, Power Management PMBus Isolation, Server Management Interface Buffering, Display and DDC Interface, Embedded Multi-Branch I2C Network, Cable-Connected Peripheral Network.
Industrial Sensor Bus Segmentation
The PCA9605D fits industrial I2C sensor networks when a controller must communicate with distributed sensors beyond the load of a direct bus connection. Its one SDA channel and one SCL channel regenerate the two-wire signals while separating the source-side and load-side bus capacitance. The 400 kHz operating limit accommodates standard Fast-mode I2C traffic, and the -40 °C to +85 °C range supports industrial equipment. Place separate pull-ups on each bus segment and verify timing against the maximum cable length and total capacitance.
推荐
Power Management PMBus Isolation
The PCA9605D can separate a PMBus controller from a load segment containing power converters or management devices. By buffering both SCL and SDA, it allows each side to retain its own pull-up network and permissible bus capacitance, which is useful when the controller and monitored hardware are separated by wiring or a connector. The 2.7 V to 5.5 V operating range supports common embedded power rails, while the 400 kHz limit covers typical management-bus traffic. Validate timing at maximum bus loading and review the exact channel connections.
推荐
Server Management Interface Buffering
The PCA9605D is appropriate for a server-management topology that distributes SCL and SDA communications across a backplane or cable segment. A 400 kHz bus buffer helps isolate the management controller from downstream peripheral loading while preserving standard two-wire signaling. The 8-pin SOIC package supports conventional surface-mount assembly, and the industrial temperature rating covers equipment-room conditions. Use short, differential-like routing where practical, keep pull-ups close to each active segment, and confirm that inrush, rise time, and connector capacitance remain inside the system timing budget.
推荐
Display and DDC Interface
The PCA9605D can buffer Display Data Channel or similar display-control traffic when an I2C-compatible display interface is separated from its host controller. Its paired SDA and SCL channels preserve the two-wire connection while isolating the two bus segments, and the 400 kHz ceiling is suitable for conventional DDC traffic. The 2.7 V to 5.5 V supply range allows use in mixed-voltage embedded systems, although it does not perform voltage translation. Confirm compatible logic thresholds, place pull-ups on each side, and route the pair away from display switching regulators to minimize coupled noise.
推荐
Embedded Multi-Branch I2C Network
The PCA9605D supports a multi-branch embedded I2C architecture by dividing the network into buffered sections. One input side remains connected to the controller, while the output side drives a group of peripherals with its own capacitance and pull-up arrangement. This arrangement is useful in systems that combine several connector branches or peripheral groups that cannot be supported reliably from one direct bus node. The 400 kHz limit and 2.7 V to 5.5 V range support common embedded interfaces, but each segment must be checked independently for capacitance, logic levels, and pull-up selection.
推荐
Cable-Connected Peripheral Network
The PCA9605D is useful for cable-connected I2C peripherals where capacitance accumulated along wiring would otherwise reduce timing margin. Buffering SDA and SCL allows the controller-side and peripheral-side capacitance budgets to be handled independently, while the 400 kHz limit supports Fast-mode communication. The 8-pin SOIC package permits compact placement near a connector or branch point. Keep both conductors routed together, minimize stubs, use appropriate pull-up resistance, and verify rise and fall times with the cable and peripheral capacitance present rather than relying only on bench conditions.
推荐
推荐产品汇总
工程参考数据: PCA9605D ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCA9600D |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOP |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Device Function | Simple two-wire bus buffer | Two-wire bus buffer |
| Lifecycle Status | Active | Active |
关键差异点
- Single bidirectional two-wire buffer for direct SCL and SDA segmentation (对比 PCA9600D)
- Industrial operating range for embedded and industrial equipment (对比 PCA9600D)
- Supports 2.7 V to 5.5 V system rails (对比 PCA9600D)
设计说明
Install separate pull-up resistors on the controller-side and buffered-load-side SDA and SCL nets. Do not leave the two bus segments tied together through pull-ups, because that defeats the isolation and capacitance-management purpose of the buffer. Select resistor values from the actual bus capacitance, pull-up voltage, leakage current, and required rise time. Place the load-side pull-ups near the PCA9605D output-side devices and the input-side pull-ups near the controlling master.
Route SDA and SCL as a closely coupled pair and keep the traces short, continuous, and away from switching nodes, inductors, high-current returns, and display or power-converter outputs. Minimize branch stubs because every stub adds capacitive loading and can create timing-margin problems. If the buffer sits near a connector or cable, provide adequate ground return, minimize loop area, and confirm that connector and cable capacitance are included in the worst-case bus calculation.
The PCA9605D is a bus buffer, not a voltage-level translator. Do not use it to connect source-side and load-side devices with incompatible logic thresholds, and do not assume that the 2.7 V to 5.5 V supply specification authorizes level translation. Confirm the enable requirements, channel direction, power-loss behavior, pull-up voltages, and maximum operating frequency from the manufacturer datasheet before placing the device in a new bus topology.
合规信息
The industrial temperature grade and surface-mount package are identified, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated in the available product information.