Microchip Technology

PIC10F206-E/MC - 4MHz 8-Bit Flash MCU | Microchip Technology

料号: PIC10F206-E/MC ✓ 量产中
2 V to 5.5 V Vdss 8-DFN (2 x 3 mm) Package 4 MHz Speed 768 bytes Flash (512 x 12 words) Memory
最小起订量: 1 |

PIC10F206-E/MC 概述

The Microchip Technology PIC10F206-E/MC is an 8-bit, fully static, Flash-based CMOS microcontroller with a 4 MHz operating frequency, 768 bytes of program memory, 24 bytes of RAM, and four I/O pins, packaged in an 8-DFN 2 x 3 mm package. The device uses a compact RISC instruction set with 33 single-word, single-cycle instructions and is designed for cost-sensitive embedded-control applications where board area, simple control, and low component count are important.

An 8-bit microcontroller is a programmable semiconductor that executes firmware to monitor inputs, control outputs, and manage embedded system behavior. Within the device hierarchy, the PIC10F206 belongs to the PIC10 family of small flash-based microcontrollers, combining a CPU core, program Flash, data RAM, I/O ports, configuration memory, and an analog comparator. The PIC10F206 adds comparator functionality to the basic PIC10F200/202/204 architecture, allowing a compact design to perform simple analog threshold measurements without a separate comparator IC.

Key device characteristics include 4 MHz operation, 768 bytes of Flash program memory organized as 512 12-bit words, 24 bytes of RAM, four general-purpose I/O pins, and an analog comparator. The operating voltage range is 2 V to 5.5 V. Its single-cycle instruction execution takes approximately 1 microsecond, while program branches require two cycles. These attributes make the controller suitable for compact products that need modest computation, limited data retention, and deterministic control rather than high-throughput processing.

The fully static RISC architecture allows the processor to stop its clock when the device enters Sleep mode. Configuration memory supports programmable operating options, while Flash program memory permits in-system reprogramming for firmware updates and production configuration. Because the device belongs to the PIC10F200/202/204/206 family, its programming tools and software ecosystem are centered around Microchip's PIC10 architecture and development environment.

Typical applications include appliance control, small sensor interfaces, battery-operated products, LED status indicators, simple motor or relay controllers, and compact embedded-control modules. The four I/O pins are sufficient for basic pushbuttons, discrete sensors, logic-level indicators, and simple actuator interfaces. Its small 2 x 3 mm DFN package also supports space-constrained boards where a larger SOIC or TSSOP package would be inappropriate.

Designers should verify the exposed-pad connection and land pattern against the manufacturer package drawing, preserve the required input, output, and decoupling layout, and account for the device's limited RAM when buffering data. Firmware should also use the device's configuration mechanisms to select the appropriate oscillator, reset behavior, and peripheral settings before normal operation begins.

This page combines the PIC10F206-E/MC architecture, programming references, package details, practical application guidance, and technically relevant drop-in comparison information to support component selection and board-level implementation.

直接替换替代料: PIC10F206-E/MC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: PIC10F206-E/MC (相同外形与封装尺寸) ——差异在于 Package, I/O Pins, Instruction Set, Operating Temperature, Program Memory.

Microchip Technology
Package: 8-pin DFN (2x3 mm)
I/O Pins: 4 (bidirectional GPIO)
Instruction Set: 33 single-word/single-cycle instructions
Microchip Technology
Package: 8-VFDFN Exposed Pad (MC), 2x3 mm
I/O Pins: 3 (GP0-GP2)
Instruction Set: 33 single-word instructions

PIC10F206-I/MC

✅ 直接替换
Microchip Technology
📦 8-DFN (2 x 3 mm)
8-bit PIC RISC · 768 B (512 x 12) Flash · 24 B (24 x 8) · 33 single-word instructions · 4 MHz (1 MIPS) · 3 (GP0-GP2) · 2.0 V to 5.5 V · Internal 4 MHz

联系询价

查看数据手册 →

PIC10F206T-I/MC

✅ 直接替换
📦 8-DFN (2 x 3 mm)
The T and I ordering designations change, while the listed 4 MHz clock, 768-byte Flash, 24-byte RAM, four I/O pins, and comparator ratings remain unchanged at 0%.

📋 参考替代料(不在目录中)

PIC10F206-E/MC 最大额定值与电气特性

Product Type 8-bit Flash-based CMOS microcontroller
CPU Architecture RISC
Instruction Set Count 33 single-word instructions
最大时钟频率 4 MHz
Program Memory 768 bytes Flash (512 x 12 words)
Data Memory 24 bytes RAM
General-Purpose I/O Pins 4 pins
Operating Voltage Range 2 V to 5.5 V
Typical Instruction Cycle Time 1 microsecond
Program Branch Cycle Time 2 microseconds
Peripheral Analog comparator
Architecture Fully static
Program Memory Type Flash
Semiconductor Process CMOS
封装 8-DFN (2 x 3 mm)
RoHS 状态 Compliant

PIC10F206-E/MC 8-dfn (2 x 3 mm) 引脚配置指南

PIC10F206-E/MC(8-dfn (2 x 3 mm) 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。

PIC10F206-E/MC 的 8-dfn (2 x 3 mm) 封装引脚图

暂无详细引脚数据: PIC10F206-E/MC.

请参阅 数据手册 以查看完整引脚配置。

典型应用

PIC10F206-E/MC 适用于 6 应用s: Compact Sensor Interface, Battery-Operated Control Module, Appliance User Interface, LED and Indicator Control, Simple Relay or Motor Control, Portable Measurement Module.

🧩

Compact Sensor Interface

The PIC10F206-E/MC fits compact sensor interfaces because it combines four I/O pins with an on-chip analog comparator in a 2 x 3 mm DFN package. A sensor signal can be evaluated against an internal or external threshold, while the firmware handles switching, filtering, status flags, and actuator commands. Its 768-byte Flash capacity is appropriate for a focused control loop, and 24 bytes of RAM can hold a small state and counter set. The main limitation is memory scale, so designs requiring history buffers, complex digital filtering, or multiple communication protocols should account for the 768-byte program and 24-byte RAM limits.

📱

Battery-Operated Control Module

The PIC10F206-E/MC is suitable for a small battery-operated control module that must conserve space while operating from a 2 V to 5.5 V supply. Its fully static architecture supports Sleep operation, and its compact 8-DFN package minimizes PCB area in wearables, portable sensors, and small household products. Four I/O pins are sufficient for a button, status LED, and simple actuator outputs. Firmware can enter Sleep between events to reduce activity, but battery life still depends on the external sensor leakage, pull networks, and regulator quiescent current, which must be evaluated separately from the microcontroller specifications.

🏭

Appliance User Interface

The PIC10F206-E/MC can implement the local control logic of an appliance user interface when the interface consists of a small number of buttons, indicators, and a simple threshold input. Its 4 MHz processing rate executes control logic rapidly, while the 768 bytes of Flash can store a compact state machine. The four I/O pins limit the number of directly connected front-panel functions, making external expansion necessary for larger key matrices or multiplexed displays. The 2 x 3 mm DFN package also helps when the control PCB must fit behind a small user-interface panel.

💡

LED and Indicator Control

The PIC10F206-E/MC is well matched to LED and indicator control because four I/O pins can drive several discrete outputs, directly control simple logic-level driver stages, or operate an indicator pattern. Its 4 MHz execution rate provides responsive sequencing, and Flash memory allows firmware patterns to be updated without replacing the device. The controller is most appropriate for short, deterministic lighting sequences rather than animation-intensive displays. Current limits, polarity, flicker behavior, and grounding should be checked against the manufacturer electrical limits before connecting LEDs directly to an I/O pin.

🔧

Simple Relay or Motor Control

The PIC10F206-E/MC can supervise a simple relay, latched switch, or low-power motor-control stage when the application requires a compact state machine rather than sophisticated motion algorithms. Four I/O pins can provide control and status signals, while the analog comparator can monitor a feedback or threshold input. The 4 MHz clock supports deterministic timing, and the 2 x 3 mm package leaves board space for the power stage. Flyback protection, driver transistors, current limiting, and isolation from inductive transients remain external design requirements.

🖥️

Portable Measurement Module

The PIC10F206-E/MC fits a portable measurement module that evaluates a modest number of inputs and reports a local result. The analog comparator provides a hardware threshold function, while 24 bytes of RAM can maintain a small working set and 768 bytes of Flash can hold configuration, calibration, and measurement sequencing. The 2 V to 5.5 V operating range permits integration with low-voltage sensor systems. It is best for binary or coarse threshold measurements; applications requiring precision conversion, large sample buffers, or complex digital signal processing need a higher-end microcontroller.

推荐产品汇总

PIC10F204 Related PIC10 family controller without the PIC10F206 comparator feature 用于: Compact Sensor Interface, Appliance User Interface, Simple Relay or Motor Control, Portable Measurement Module PIC10F202 Related low-cost PIC10 controller for simpler discrete I/O designs 用于: Compact Sensor Interface, Battery-Operated Control Module, Appliance User Interface, LED and Indicator Control, Simple Relay or Motor Control, Portable Measurement Module PIC10F200 Related PIC10 controller for minimal portable-control functions 用于: Battery-Operated Control Module, LED and Indicator Control
What are the key specifications of PIC10F206-E/MC that engineers should know?
The PIC10F206-E/MC is a 4 MHz, 8-bit, fully static Flash microcontroller with 768 bytes of program memory, 24 bytes of RAM, four I/O pins, and an analog comparator in an 8-DFN package. According to the Microchip PIC10F200/202/204/206 datasheet, most instructions execute in one cycle of approximately 1 microsecond, while program branches require two cycles. Its operating voltage range is 2 V to 5.5 V.
Where can I download the PIC10F206 datasheet PDF?
The PIC10F206 datasheet is available from Microchip Technology at the official PDF URL for the PIC10F200/202/204/206 family. The document covers the 6-pin and related package options, architecture, program memory, RAM, comparator, electrical characteristics, programming information, and package drawings. Use the 40001239F document only after confirming that its package and ordering information include the PIC10F206-E/MC configuration.
What is the pin configuration of PIC10F206-E/MC?
The PIC10F206-E/MC uses an 8-DFN 2 x 3 mm package with six device connections plus a thermal or ground-related exposed pad. Its exact pin names and numbering must be taken from the pin-description table and land-pattern drawing in the manufacturer datasheet because the exposed pad must be connected according to the package drawing. Verify the complete pin map before assigning PCB tracks or programming the configuration words.
How do I program a PIC10F206?
A PIC10F206 is programmed through its in-system programming interface using compatible Microchip programming equipment and software supporting the PIC10 family. The device contains Flash program memory, so the configured firmware can be written and subsequently updated. The programming process must follow the electrical and timing requirements in the PIC10F200/202/204/206 datasheet, including the required pins, supply voltage, and programming-mode entry sequence.
Where can I buy PIC10F206-E/MC online?
PIC10F206-E/MC can be requested through the Request a Quote form on this page. The form supports exact-MPN sourcing and lets you state the required quantity, packaging preference, target date, and shipment destination. Current commercial terms should be confirmed through that form because component availability, order quantities, and lead time can change by region and production schedule.
What is the price of PIC10F206-E/MC?
The current commercial price for PIC10F206-E/MC is not stated in this page's technical content. Submit the exact MPN through the Request a Quote form on this page to request current unit pricing and volume pricing for the required quantity. This approach keeps the quote tied to the exact 8-DFN ordering code rather than a family-level or possibly different package variant.
What is the lead time for PIC10F206-E/MC?
The current lead time for PIC10F206-E/MC should be confirmed through the Request a Quote form on this page. Include your required order quantity, delivery date, approved destination, and whether reel or another delivery format is required. A manufacturing or allocation schedule may affect lead time, so the quotation is the appropriate source for a binding delivery commitment.
Is PIC10F206-E/MC in stock?
PIC10F206-E/MC is currently presented as an active catalog device, but project-specific stock should not be assumed from a general product listing. Request availability and a delivery commitment through the Request a Quote form on this page. Provide the exact MPN, quantity, and target delivery date so the response can reflect the current fulfillment position.
What is the difference between PIC10F206-E/MC and PIC10F206-I/MC?
PIC10F206-E/MC and PIC10F206-I/MC retain the same 4 MHz core, 768-byte Flash program memory, 24-byte RAM, four I/O pins, and comparator, and both are associated with the same DFN package family. Their primary ordering difference is the E versus I temperature-grade designation. Check the manufacturer ordering information and temperature limits before deciding whether a grade change affects qualification or reliability requirements.
Is PIC10F206T-I/MC a drop-in replacement for PIC10F206-E/MC?
PIC10F206T-I/MC is the same PIC10F206 device family with a T reel-oriented ordering code and the I temperature-grade designation. Its core parameters remain 4 MHz operation, 768 bytes of Flash, 24 bytes of RAM, and four I/O pins, matching the target's functional ratings at 0%. The ordering-code and temperature-grade differences must be reviewed before treating it as an unqualified substitute.
What can replace PIC10F206-E/MC?
PIC10F206-I/MC is the closest documented drop-in candidate because it retains the PIC10F206 core, 4 MHz clock, 768-byte Flash memory, 24-byte RAM, four I/O pins, and the same package family. Its E-versus-I grade designation changes the ordering specification rather than the listed functional ratings. Confirm the exact package drawing, temperature requirements, and device configuration before approving a replacement.
When should I choose PIC10F206-E/MC over PIC10F206-I/MC?
Choose PIC10F206-E/MC when its E temperature-grade designation matches the product's environmental requirements and the PCB is designed for the exact 8-DFN footprint. Choose PIC10F206-I/MC when the application requires the I grade while retaining the same listed core resources and DFN package family. The decision should be based on the manufacturer's temperature tables and qualification needs, not merely on the functional memory and clock specifications.
Is PIC10F206-E/MC suitable for a compact sensor interface?
The PIC10F206-E/MC is suitable for a compact sensor interface when the design needs four I/O lines, an on-chip comparator, and modest firmware capacity. Its 2 V to 5.5 V operating range supports low-voltage systems, while 768 bytes of Flash and 24 bytes of RAM are adequate for basic thresholding, debouncing, and state control. More demanding buffering or protocol handling may exceed those memory resources.
What is the best Microchip equivalent for PIC10F206-E/MC?
The best directly identified Microchip equivalent is PIC10F206-I/MC because it preserves the 4 MHz clock, 768 bytes of Flash, 24 bytes of RAM, four I/O pins, comparator, and DFN package family. The functional-parameter difference for the listed ratings is 0%, with the E-versus-I grade designation serving as the ordering distinction. Verify temperature limits and the exact land pattern before using it as a drop-in replacement.
What are the engineering trade-offs of the PIC10F206-E/MC?
The principal trade-offs are compact size and low component count versus limited resources. The PIC10F206-E/MC provides only 768 bytes of Flash, 24 bytes of RAM, and four I/O pins, so complex protocols, large buffers, and extensive application logic may not fit. Its 2 x 3 mm DFN package also requires careful exposed-pad handling and compact PCB layout, but it is well suited to simple embedded-control products.

工程参考数据: PIC10F206-E/MC ——对比、设计指导和合规信息。

选型指南

Choose PIC10F206-E/MC for a compact embedded-control design that needs 4 MHz processing, 768 bytes of Flash, 24 bytes of RAM, four I/O pins, and an analog comparator within a 2 x 3 mm DFN package. Its architecture is strongest for simple appliance controls, threshold sensors, portable modules, indicator logic, and small relay or switch controllers. PIC10F206-I/MC is appropriate when the product's environmental requirements call for the I temperature grade while the functional ratings and package family remain unchanged. PIC10F206T-I/MC provides the same listed PIC10F206 resources with T and I ordering designations and should be selected only after confirming the exact reel-oriented ordering convention. Neither listed alternative expands Flash, RAM, I/O, clock speed, or comparator capability, so moving between them does not solve an application that has outgrown the PIC10F206's resource limits.

与替代料对比

参数 本产品 PIC10F206-I/MC PIC10F206T-I/MC
Brand Microchip Technology Microchip Technology Microchip Technology
Package 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm)
CPU Architecture 8-bit RISC 8-bit RISC 8-bit RISC
Maximum Clock Frequency 4 MHz 4 MHz 4 MHz
Program Memory 768 bytes Flash (512 x 12 words) 768 bytes Flash (512 x 12 words) 768 bytes Flash (512 x 12 words)
Data Memory 24 bytes RAM 24 bytes RAM 24 bytes RAM
General-Purpose I/O Pins 4 pins 4 pins 4 pins
Operating Voltage Range 2 V to 5.5 V 2 V to 5.5 V 2 V to 5.5 V
Analog Comparator Yes Yes Yes
Instruction Set 33 single-word, single-cycle instructions 33 single-word, single-cycle instructions 33 single-word, single-cycle instructions

关键差异点

  • Comparator-equipped PIC10 core in a compact footprint (对比 PIC10F206-I/MC)
  • Same core resources with an ordering-code configuration (对比 PIC10F206T-I/MC)

设计说明

Use the manufacturer land-pattern drawing for the 8-DFN 2 x 3 mm package and connect the exposed pad exactly as specified. Place the device near its decoupling capacitor, keep the pad path short, and provide adequate solderable area for thermal dissipation. Because the exposed pad is part of the land pattern rather than an optional mechanical feature, do not substitute a generic DFN footprint without cross-checking pad dimensions.

Design the supply path for the stated 2 V to 5.5 V operating range and follow the manufacturer's recommended bypass-capacitor arrangement. Place the primary capacitor adjacent to the supply and ground pins to limit high-frequency supply impedance. Confirm startup, brownout, and maximum voltage behavior against the device's electrical characteristics, particularly when the controller shares a rail with motors, relays, or other switching loads.

Do not exceed the 768-byte Flash or 24-byte RAM limits when estimating firmware requirements, and include the bootloader, configuration values, and interrupt routines in that budget. Four I/O pins also limit direct button, LED, and actuator assignments. Use the programming and configuration tables in the manufacturer datasheet rather than assuming that another PIC10 family's configuration words or pin behavior are identical.

When using the analog comparator, route the relevant signal through a short and electrically quiet path, keep it away from switching-node copper, and connect the exposed-pad ground arrangement as directed by the package drawing. Comparator threshold accuracy can be affected by source impedance, grounding, and nearby noise. Validate the complete analog front end with the intended sensor and operating conditions instead of relying only on nominal timing specifications.

合规信息

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

RoHS compliance is identified for the exact MPN. No verified AEC-Q100, REACH, halogen-free, lead-free, or conflict-minerals declaration is available for this ordering configuration.

数据核验日期: 2026-11-15 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

PIC10F206 datasheet PIC10F206 programming PIC10F206-E/MC datasheet pdf PIC10F206-E/MC pinout PIC10F206-E/MC equivalent PIC10F206-E/MC replacement PIC10F206-E/MC footprint PIC10F206-E/MC price PIC10F206-E/MC stock Microchip PIC10F206-E/MC PIC10F206 vs PIC10F206-I/MC PIC10F206 4MHz comparator application

相关元器件 & 术语

Microchip Technology PIC10F206 PIC10F206-E/MC PIC10F206-I/MC PIC10F206T-I/MC PIC10F200/202/204/206 family 8-bit microcontroller RISC architecture Flash memory static CMOS microcontroller analog comparator 4 MHz clock 768-byte program memory 24-byte RAM four I/O pins 2 V to 5.5 V operating range 8-DFN 2 x 3 mm package QFN family surface-mount package in-system programming Sleep mode RoHS embedded control threshold sensing
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情