PIC12F609-E/MF - 8-Bit MCU, 1.75KB Flash, 6 I/O | Microchip
料号： PIC12F609-E/MF ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $1.04 | $1.04 |
| 10 | $0.94 | $9.40 |
| 100 | $0.84 | $84.00 |
| 500 | $0.74 | $370.00 |
| 1,000 | $0.66 | $660.00 |
| 3,000 | $0.58 | $1,740.00 |
PIC12F609-E/MF 概述
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals onto one silicon die. The PIC12 family sits in Microchip's mid-range architecture tier, between the baseline 8-bit PIC10/16 cores and the enhanced 16-bit PIC24/dsPIC families. Within the broader taxonomy, MCUs belong to microcontrollers -> embedded processors -> digital ICs -> semiconductors. The PIC12F609 specifically targets applications needing small package count, internal oscillator accuracy, and minimal BOM cost.
Key features include 1.75KB (1K x 14) Flash program memory, 64 x 8 RAM, hardware peripherals such as Brown-out Detect/Reset (BOR) and Power-on Reset (POR), an 8-bit timer (TMR0) and a 16-bit timer (TMR1), a comparator module, and a 10-bit ADC (shared with comparator input on adjacent pins). The internal 8MHz oscillator eliminates the need for an external crystal, reducing system cost and board area. The device supports in-circuit serial programming (ICSP) and in-circuit debugging via two dedicated pins.
The PIC12F609 uses a RISC architecture with only 35 instructions, enabling deterministic single-cycle execution (except branches). The wide 2.0V-5.5V supply range supports both 3.3V and 5V system designs, and the DFN-8 package with exposed pad offers low thermal resistance in compact layouts. Low-power features include nanoWatt technology with sleep currents below 1 microamp, plus multiple oscillator modes for active-vs-standby current trade-offs.
Typical applications include LED lighting controllers, small appliance control, battery chargers, sensor signal conditioning, automotive body electronics (using the automotive-qualified PIC12F609T-I/MF variant), and consumer remote-control encoders. The combination of small pin count and integrated peripherals also suits smart IoT edge nodes and wearables.
When designing with this MCU, ensure the ICSPDAT and ICSPCLK pins are not pulled low at reset to enter programming mode unintentionally, and follow Microchip's AC/DC input-output layout guideline for the comparator/ADC shared pins to avoid digital switching noise coupling into analog measurements.
This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not collected on any single manufacturer or distributor page, giving engineers a single starting point for PIC12F609 evaluation and sourcing.
直接替换替代料： PIC12F609-E/MF ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC12F609-E/MF （相同外形与封装尺寸） ——差异在于 Package, Internal Oscillator, Operating Temperature, Timers, Core.
快速对比工具——选择替代料号进行并排对比：
PIC12F609-E/MD
✅ 直接替换✓ 有现货
$0.66 / 个
查看数据手册 →PIC12F615-E/MF
✅ 直接替换📋 参考替代料（不在目录中）
PIC12F617-E/MF
✅ 直接替换✓ 有现货
$0.71 / 个
查看数据手册 →PIC12F609-I/MF
✅ 直接替换✓ 有现货
$0.59 / 个
查看数据手册 →PIC12F609T-I/MF
✅ 直接替换📋 参考替代料（不在目录中）
PIC12HV609-E/MF
✅ 直接替换📋 参考替代料（不在目录中）
PIC12F609-E/MF 最大额定值与电气特性
| Core Architecture | PIC12 mid-range 8-bit RISC |
| Program Memory (Flash) | 1.75 KB (1K x 14) |
| RAM | 64 x 8 bytes |
| Data EEPROM | Not present (0 bytes) |
| Maximum CPU Speed | 20 MHz |
| Internal Oscillator | 8 MHz (calibrated) |
| Supply Voltage (VDD) | 2.0 V to 5.5 V |
| I/O Pins | 5 (plus 1 input-only on RA3, total 6 I/O per family) |
| 封装 | 8-pin DFN with exposed pad (MF / HVSON) |
| 工作温度 | -40 C to +125 C (E = Extended) |
| Comparators | 1 (per family datasheet) |
| Timers | TMR0 (8-bit), TMR1 (16-bit) |
| Watchdog Timer | Yes (WDT with dedicated on-chip oscillator) |
| Brown-out Reset (BOR) | Yes, configurable |
| ICSP Programming | Yes (ICSPDAT, ICSPCLK) |
| Instruction Set | 35 instructions, single-cycle except branches |
| RoHS 状态 | Compliant |
PIC12F609-E/MF 引脚配置
| 引脚 1 | RA3/GP3/MCLR/VPP — Digital I/O (input only) / Master Clear reset / ICSP programming voltage |
| 引脚 2 | RA4/GP4/AN3/C1OUT/T1G/OSC2/CLKOUT — Digital I/O / Analog input 3 / Comparator 1 output / Timer1 gate / Oscillator output / Clock output |
| 引脚 3 | RA5/GP5/AN2/C1IN+/OSC1/CLKIN — Digital I/O / Analog input 2 / Comparator 1 non-inverting input / Oscillator input / External clock input |
| 引脚 4 | RA0/GP0/AN0/C1IN-/ICSPDAT — Digital I/O / Analog input 0 / Comparator 1 inverting input / ICSP data |
| 引脚 5 | RA1/GP1/AN1/VREF/C1IN0/ICSPCLK — Digital I/O / Analog input 1 / Voltage reference / Comparator reference / ICSP clock |
| 引脚 6 | RA2/GP2/AN4/INT/C1OUT/T0CKI — Digital I/O / Analog input 4 / External interrupt / Comparator output / Timer0 clock input |
| 引脚 7 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
| 引脚 8 | VSS — Ground reference |
| 引脚 EP | Exposed Pad — Thermal pad; tie to VSS for optimal thermal dissipation (per datasheet layout guideline) |
典型应用
PIC12F609-E/MF 适用于 6 应用s: LED Lighting Controllers, Small Appliance and White Goods Control, Battery-Powered Sensor Nodes, Automotive Body Electronics (Auxiliary), Consumer Remote Control Encoders, Industrial Sensor Signal Conditioning.
LED Lighting Controllers
The PIC12F609-E/MF fits low-cost LED lighting controllers because its 8-pin DFN package occupies minimal PCB area while the 2.0-5.5 V supply range directly supports single-cell Li-ion or 3.3 V regulated rails. Its 8 MHz internal oscillator eliminates external crystal cost, and the comparator can be used for zero-cross detection or analog dimming feedback. Unlike higher-pin-count PIC16 parts, the PIC12F609 leaves just enough I/O (5 GPIO + 1 input) to drive an LED MOSFET, read a push-button, and route an enable signal. Compared to the PIC12F615, the PIC12F609 omits the 10-bit ADC and PWM, which keeps firmware simple for on/off or single-stage dimming designs where software PWM suffices.
推荐
Small Appliance and White Goods Control
The PIC12F609-E/MF suits small appliance control boards such as coffee makers, blenders, and air purifiers where 5-6 I/O pins are enough for switch inputs, relay drivers, and indicator LEDs. Its extended -40 C to +125 C temperature grade (E suffix) survives under-hood or near-heater mounting, and integrated BOR/POR ensures clean MCU startup after brown-outs common with inductive loads. The 1.75 KB Flash holds typical state-machine firmware for one or two motor or heater modes. Compared to a 14- or 20-pin PIC16, the PIC12F609 reduces PCB footprint and BOM cost in price-sensitive consumer appliances.
推荐
Battery-Powered Sensor Nodes
The PIC12F609-E/MF operates down to 2.0 V, supporting direct connection to a single CR2032 coin cell or two AAA cells. Its nanoWatt sleep mode with sub-microamp standby current enables multi-year battery life in remote sensor nodes, while the integrated comparator handles threshold-based wake-up from external sensors without burning ADC power. The DFN-8 package with exposed pad also helps thermal dissipation in confined enclosures. Unlike 32-bit Cortex-M0 alternatives, the PIC12F609 costs well under $1 in volume, making it ideal for disposable or ultra-low-cost IoT endpoints.
推荐
Automotive Body Electronics (Auxiliary)
The PIC12F609-E/MF handles auxiliary automotive body functions such as LED interior lighting, seat-position encoders, and accessory switches. While the E suffix supports -40 C to +125 C, AEC-Q100 Grade 1 qualification requires the PIC12F609T-I/MF automotive variant. The MCU's small footprint and integrated peripheral set (comparator, WDT, BOR) fit under-dash and inside-door modules where PCB area is scarce. Compared to PIC16F series MCUs, the PIC12F609 keeps per-unit cost low for non-safety functions like puddle lamps and courtesy lighting.
推荐
Consumer Remote Control Encoders
The PIC12F609-E/MF fits infrared or RF remote control encoders thanks to its 1.75 KB Flash (enough for one-button-to-many-button matrix scanning) and sub-1 microamp sleep current that preserves coin-cell battery life for years. Its 8 MHz internal oscillator provides adequate timing for IR carrier generation (38-56 kHz) without external components. The wide 2.0-5.5 V supply range accommodates both 3 V lithium and 1.5 V x2 alkaline batteries. Unlike dedicated IR encoder ICs, the PIC12F609 lets designers implement custom protocols via firmware.
推荐
Industrial Sensor Signal Conditioning
The PIC12F609-E/MF works as a low-cost front-end signal conditioner in industrial 4-20 mA loops, RTD bridges, or thermistor networks. Its on-chip comparator performs threshold detection without ADC overhead, while the extended -40 C to +125 C temperature grade handles outdoor and cabinet environments. The DFN-8 package's exposed pad simplifies PCB thermal layout for continuous operation near heat-generating power components. For designs needing actual analog-to-digital conversion, the PIC12F615-E/MF in the same footprint provides a firmware-compatible upgrade path.
推荐
推荐产品汇总
工程参考数据： PIC12F609-E/MF ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC12F609-E/MD | PIC12F615-E/MF | PIC12F617-E/MF | PIC12F609-I/MF | PIC12HV609-E/MF |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin DFN with exposed pad (MF) | 8-pin DFN equivalent (MD) | 8-pin DFN with exposed pad | 8-pin DFN with exposed pad | 8-pin DFN with exposed pad | 8-pin DFN with exposed pad |
| Program Memory (Flash) | 1.75 KB (1K x 14) | 1.75 KB | 1.75 KB | 1.75 KB | 1.75 KB | 1.75 KB |
| RAM | 64 bytes | 64 bytes | 64 bytes | 128 bytes (extended) | 64 bytes | 64 bytes |
| I/O Pins | 6 | 6 | 6 | 6 | 6 | 6 |
| 10-bit ADC | No (comparator only) | No | Yes | Yes | No | No |
| PWM Module | No | No | Yes | Yes (enhanced) | No | No |
| Supply Voltage | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V plus HV shunt |
| Temperature Grade | Extended -40 C to +125 C | Extended -40 C to +125 C | Extended -40 C to +125 C | Extended -40 C to +125 C | Industrial -40 C to +85 C | Extended -40 C to +125 C |
关键差异点
- Internal 8 MHz calibrated oscillator eliminates external crystal （对比 PIC12F508-E/MF)
- Extended -40 C to +125 C temperature grade in compact DFN-8 （对比 PIC12F509-I/MS)
- Upgrade path to PIC12F615 adds 10-bit ADC and PWM without PCB changes （对比 PIC12F508-E/MF)
- Integrated comparator for analog threshold detection without ADC （对比 PIC12F519-I/P)
设计说明
Route the ICSPDAT (RA0/GP0, pin 4) and ICSPCLK (RA1/GP1, pin 5) lines so they are not pulled low at reset or during normal operation, otherwise the MCU may inadvertently enter programming mode. Per Microchip's family datasheet, both pins must be held high with 4.7 kohm pull-ups during normal runtime. Place these pull-ups close to the MCU pins, and keep the ICSP traces short to avoid signal-integrity issues during in-circuit programming. Estimated: typical 4.7 kohm pull-up values are industry standard, not a datasheet-specified figure.
RA3 on the PIC12F609 is input-only - it cannot be configured as an output. Designers used to PIC16F or PIC18F parts often make the mistake of setting TRISIO bit 3 to output. Per the datasheet, this bit is read-only and the pin is always an input. Plan your I/O map accordingly: reserve RA3 for input-only functions such as MCLR reset, a push-button, or a digital sensor output. For applications needing 5 outputs, the PIC12F615 in the same package adds ADC and PWM capability without changing the I/O count.
The PIC12F609-E/MF uses a DFN-8 package with exposed thermal pad that MUST be soldered to a copper pad on the PCB for mechanical reliability and thermal dissipation. Per Microchip's package outline, the exposed pad is internally connected to VSS (ground). Route a copper pour of at least 10 mm x 10 mm on the top layer beneath the IC, with thermal vias to the inner ground plane, to keep junction temperature within ratings under sustained 20 MHz operation. Estimated: pad area recommendation is a typical layout guideline, not a hard datasheet limit.
The PIC12F609 shares analog comparator input pins (C1IN-, C1IN+, C1IN0) with digital I/O and ICSP functions. Per the family datasheet, switching adjacent digital pins at high frequency can couple noise into the comparator threshold measurement. Keep analog input traces short and guarded by a ground pour; enable the digital input buffer disable bits (ANSEL register on related parts, IOC control here) to reduce digital switching injection when a pin is used for analog. For high-impedance sensors, add a small RC filter on the comparator input.
Place a 0.1 uF ceramic decoupling capacitor as close as possible to the VDD pin (pin 7) and a bulk 1-10 uF electrolytic or ceramic on the VDD rail. Per Microchip's PIC12F family design checklist, decoupling distance should be less than 5 mm between the cap and the VDD pin. The MCU's nanoWatt sleep currents drop below 1 uA when the internal oscillator is shut down, but the WDT and BOR must be configured to enable this - leaving them on default raises standby current to tens of microamps.
合规信息
RoHS and lead-free per Microchip product page. E temperature grade is -40 C to +125 C but does NOT constitute AEC-Q100 qualification - use PIC12F609T-I/MF (T = automotive qualified tape and reel) for AEC-Q100 applications.
