PIC24EP32MC202-E/SS - 60 MIPS 32KB Motor MCU | Microchip
料号: PIC24EP32MC202-E/SS ✓ 量产中PIC24EP32MC202-E/SS 概述
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one die. The PIC24E belongs to the 16-bit microcontroller hierarchy and combines a DSP-capable instruction set with dedicated resources for motor control. This combination allows a single device to measure position or current, execute control algorithms, and generate accurately timed PWM outputs without relying on several separate analog and timing components.
Key device characteristics include 32 KB of Flash memory for application code, 4 KB of SRAM for control variables and working data, a maximum 60 MIPS rating in the exact ordering code, and an operating temperature range of -40°C to +125°C. The motor-control feature set includes MCPWM peripherals, internal operational amplifiers, comparators, and Peripheral Touch-on-GPIO, while the ADC resources support both 10-bit and 12-bit conversion functions.
The PIC24E architecture is suited to closed-loop systems where execution latency and deterministic peripheral timing matter. Its enhanced on-chip peripherals support energy-efficient, quiet motor operation by consolidating feedback acquisition, signal conditioning, and power-stage control into one package. Designers can use the internal amplifiers with suitable external networks to condition current-sense signals, use comparators for threshold or protection decisions, and use PTG-capable I/O for touch or position-related functions.
Typical uses include two-phase and three-phase brushless DC motor controllers, stepper-motor drivers, servo-control loops, fan and pump controllers, power-tool drives, and compact industrial automation modules. The 28-pin SSOP is especially useful where component density matters but a leaded or very large fine-pitch package would be unnecessary.
PCB design should preserve clean current-sense and feedback paths, keep switching-node connections compact, and provide appropriate decoupling at every supply pin. Because SSOP leads are closely spaced, inspect the manufacturer land pattern and solder-profile recommendations before assembly. Verify motor-power transients, analog-input scaling, and shutdown behavior at the system level rather than relying only on nominal MCU specifications.
This product overview combines the manufacturer device description with verified package, memory, speed, converter, and peripheral details, while also documenting drop-in alternatives, comparison parameters, and practical implementation guidance for motor-control engineers.
直接替换替代料: PIC24EP32MC202-E/SS ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PIC24EP32MC202-I/SS
✅ 直接替换📋 参考替代料(不在目录中)
PIC24EP64MC202-I/SS
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →PIC24EP32MC203-I/SS
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PIC24EP64MC203-I/SS
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PIC24EP128MC202-I/SS
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PIC24EP32MC202-E/SS 最大额定值与电气特性
| Product Type | 16-bit PIC24E motor-control microcontroller |
| Maximum Performance | 60 MIPS |
| Family Architecture Performance | Up to 70 MIPS |
| Program Memory | 32 KB Flash |
| Program Memory Organization | 10.7K x 24 words |
| Data Memory | 4 KB RAM |
| ADC Resolution | 10-bit and 12-bit |
| Motor-Control Peripheral | MCPWM |
| Analog Resources | Internal operational amplifiers and comparators |
| Capacitive-Sensing Peripheral | Peripheral Touch-on-GPIO (PTG) |
| 工作温度范围 | -40°C to +125°C |
| 封装 | 28-pin SSOP |
| Package Code | SS |
| Package Width | 5.30 mm |
| Package Height | 2.00 mm |
| 安装类型 | Surface mount |
| Flash Memory | 32 KB |
| SRAM | 4 KB |
| 引脚数 | 28 pins |
| AEC-Q100 Status | Qualified |
PIC24EP32MC202-E/SS 2.00 mm 引脚配置指南
PIC24EP32MC202-E/SS(2.00 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: PIC24EP32MC202-E/SS.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PIC24EP32MC202-E/SS 适用于 6 应用s: Three-Phase Brushless DC Motor Control, Stepper-Motor Position and Current Control, Power-Tool Motor Drive, Fan and Pump Speed Control, Servo and Precision Actuator Control, Industrial Automation and Embedded Modules.
Three-Phase Brushless DC Motor Control
PIC24EP32MC202-E/SS fits a compact three-phase brushless DC motor controller because its MCPWM peripherals support deterministic complementary switching, while the 10-bit and 12-bit ADC resources acquire phase, position, and current feedback. The 60 MIPS processor performance supports faster control-loop execution than a basic general-purpose MCU. Place the MCU near the gate-driver interface, connect current-sense channels to the ADC and comparator inputs, and isolate switching-node feedback from sensitive analog traces. The integrated operational amplifiers can reduce the need for external conditioning, although component values and common-mode limits must be checked against the circuit.
推荐
Stepper-Motor Position and Current Control
PIC24EP32MC202-E/SS is suitable for stepper-motor modules that require position feedback, controlled excitation, and current regulation in a small package. The 32 KB Flash accommodates motion sequences and control code, while 4 KB RAM supports state tracking and loop variables. Its comparators and ADCs can monitor current or position-related signals, and the motor-control PWM resources can produce the stepping waveform. Layout should place current-sense filtering close to the MCU, use a defined analog ground strategy, and keep step-driver and motor-current paths away from communication and precision-feedback nets.
推荐
Power-Tool Motor Drive
PIC24EP32MC202-E/SS can support a compact power-tool drive where rapid current control, speed regulation, and protective shutdown are required. Its 60 MIPS rating allows the control firmware to combine PWM generation with current sampling, load detection, and fault handling. The 28-pin SSOP helps reduce board area, but high-current power stages must remain physically separated from the MCU and analog network. Use short gate-drive traces, provide local supply decoupling, and define a safe disable path so a controller fault cannot leave the bridge unintentionally energized.
推荐
Fan and Pump Speed Control
PIC24EP32MC202-E/SS is appropriate for efficient fan and pump controllers where variable speed, load feedback, and quiet operation are priorities. The MCPWM resources can generate actuator commands, and the ADC, comparator, and amplifier resources can monitor speed, pressure-derived signals, or current. The 60 MIPS control capability allows closed-loop calculations without offloading them to an external processor. For reliable deployment, include input filtering, sensor-ground design, thermal monitoring, and a defined behavior for blocked rotors, dry running, or communication loss.
推荐
Servo and Precision Actuator Control
PIC24EP32MC202-E/SS can serve as the digital controller in a compact servo or precision actuator because it combines fast execution with dedicated feedback and PWM peripherals. The 32 KB Flash provides room for motion tables or calibration parameters, while 4 KB RAM supports real-time control state. Its internal analog resources can reduce signal-conditioning component count when configured correctly. The designer should budget sufficient timing margin for the complete loop, calibrate position sensing after assembly, and protect the MCU from motor-transient events with appropriate routing and external clamping.
推荐
Industrial Automation and Embedded Modules
PIC24EP32MC202-E/SS fits compact industrial automation modules that need real-time motor control alongside embedded control logic. Its -40°C to +125°C temperature range and AEC-Q100 identification support demanding product categories when the full qualification and application requirements are satisfied. The 28-pin SSOP package offers a practical upgrade path for boards constrained in area. Industrial designs should separate high-energy motor routing from analog sensing, provide robust brownout and overvoltage behavior, and validate EMC margins at the assembled enclosure level.
推荐
推荐产品汇总
工程参考数据: PIC24EP32MC202-E/SS ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC24EP32MC202-I/SS | PIC24EP64MC202-I/SS | PIC24EP32MC203-I/SS | PIC24EP64MC203-I/SS |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-pin SSOP | 28-pin SSOP - same | 28-pin SSOP - same | 28-pin SSOP - same | 28-pin SSOP - same |
| Program Memory | 32 KB Flash | 32 KB Flash | 64 KB Flash | 32 KB Flash | 64 KB Flash |
| Data Memory | 4 KB RAM | 4 KB RAM | 8 KB RAM | 4 KB RAM | 8 KB RAM |
| Temperature Grade | -40°C to +125°C | Industrial grade | Industrial grade | Industrial grade | Industrial grade |
关键差异点
- Maintains the same 28-pin SSOP footprint in the closest alternative (对比 PIC24EP32MC202-I/SS)
- Provides more program memory without changing the package class (对比 PIC24EP64MC202-I/SS)
- Targets the verified 32 KB, 4 KB RAM motor-control configuration (对比 PIC24EP32MC203-I/SS)
设计说明
Route current-sense and position-feedback traces as short analog paths directly from the sensing network to the relevant ADC or comparator pins. Keep switching-node and motor-phase conductors away from these inputs, use a continuous ground reference, and place analog filtering close to the MCU pins. The integrated amplifiers can reduce external conditioning, but their input networks, common-mode range, and settling behavior must still be checked against the feedback signal.
Separate the MCU supply path from high-current motor and gate-driver loads. Place local decoupling at the supply pins and use the manufacturer’s recommended capacitor network and layout. Confirm supply limits, brownout behavior, and startup sequencing in the electrical-characteristics tables of data sheet 70657F. Motor transients should be controlled at the power-stage level rather than relying on the microcontroller input protection network.
Do not substitute by the base MPN alone: the package and ordering suffix distinguish the 28-pin SSOP device from related package options such as QFN and SOIC variants. Before replacing PIC24EP32MC202-E/SS, compare the complete pin table, peripheral mapping, Flash and RAM needs, programming configuration, temperature grade, qualification, and mixed-signal limits. Firmware migration also requires verification because changes in MC202, MC203, or larger-memory family members may alter peripheral behavior.
合规信息
The verified product listing identifies the device as automotive and AEC-Q100 qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not found and remain unknown.