PIC32MZ1024EFE124-E/TL - 180MHz 1MB Flash 32-bit MCU | Microchip
料号： PIC32MZ1024EFE124-E/TL ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $13.5 | $13.50 |
| 10 | $12.42 | $124.20 |
| 100 | $11.07 | $1,107.00 |
| 500 | $9.95 | $4,975.00 |
| 1,000 | $8.91 | $8,910.00 |
PIC32MZ1024EFE124-E/TL 概述
A 32-bit microcontroller (MCU) is a microprocessor integrated with on-chip memory, peripherals, and I/O that executes instructions over a 32-bit data path. The PIC32MZ EF family specifically targets high-end connectivity, graphics, and motor-control applications by combining ample SRAM for protocol stacks, dual-panel Flash for live firmware updates, and a rich peripheral set including Hi-Speed USB, Ethernet, CAN-FD, and multiple SPI/I2C interfaces. This places the family in the broader taxonomy: microcontroller -> embedded processor -> semiconductor device.
Key features of the PIC32MZ1024EFE124-E/TL include four 64-bit accumulators for DSP operations, single-cycle MAC with saturating and fractional math, a 12-bit ADC module with up to 5 MSPS sampling rate, six UART modules, four SPI ports, four I2C ports, and a 97-pin general-purpose I/O count supporting change-notification on every pin. The integrated FPU eliminates software-emulated float math, reducing latency for control-loop and signal-processing code paths.
The architecture combines a 200 MHz-capable MIPS Warrior core (binned to 180 MHz in this -E extended-temperature variant) with tightly-coupled SRAM and dual-panel Flash, enabling Live Update firmware swaps without CPU stall. Six DMA channels and a high-bandwidth peripheral bus allow data streaming between ADC, communication peripherals, and memory with minimal CPU intervention, which is essential for real-time industrial and automotive subsystems.
Typical applications include industrial automation controllers, automotive body and infotainment ECUs, IoT edge gateways, HMI/graphics terminals, and motor-control drives. The AEC-Q100 qualification and -40C to +125C operating range make it suitable for harsh-environment deployments where reliability under thermal stress is mandatory.
When designing with this MCU, allocate decoupling capacitors close to each VDD/VSS pair and route the 124-pin VTLA land pattern on a 0.5 mm pitch footprint. The exposed thermal pad must be soldered to a continuous ground plane to meet the datasheet's thermal resistance specification. Use MPLAB Harmony v3 for peripheral configuration and to leverage the DSP library and FPU-optimized math routines.
This page synthesizes distributor pricing, parametric drop-in alternatives from the same PIC32MZ EF family, and practical PCB/thermal design notes that complement the manufacturer datasheet.
直接替换替代料： PIC32MZ1024EFE124-E/TL ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC32MZ1024EFE124-E/TL （相同外形与封装尺寸） ——差异在于 Package, Core Architecture, Operating Temperature, ADC, FPU.
快速对比工具——选择替代料号进行并排对比：
PIC32MZ1024EFE124T-E/TL
✅ 直接替换📋 参考替代料（不在目录中）
PIC32MZ1024ECM124-I/TL
✅ 直接替换✓ 有现货
$7.85 / 个
查看数据手册 →PIC32MZ1024ECH124-I/TL
✅ 直接替换✓ 有现货
$9.3 / 个
查看数据手册 →PIC32MZ1024EFE124-I/TL
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$9.4 / 个
查看数据手册 →PIC32MZ1024EFK124-E/TL
✅ 直接替换📋 参考替代料（不在目录中）
PIC32MZ1024EFE124-E/TL 最大额定值与电气特性
| Core Architecture | MIPS32 M-Class (MIPS Warrior) |
| 数据总线宽度 | 32-bit |
| Maximum CPU Speed | 180 MHz |
| Performance | 330 DMIPS |
| Program Memory (FLASH) | 1 MB (1M x 8) |
| SRAM | 256 KB |
| FPU | IEEE 754 single/double precision |
| DSP | Four 64-bit accumulators, single-cycle MAC |
| Operating Voltage | 2.1 V to 3.6 V |
| 工作温度 | -40 C to +125 C (E = Extended) |
| 封装 | 124-pin VTLA (9x9 mm, 0.5 mm pitch) |
| I/O Pins | 97 programmable I/O lines |
| AEC-Q100 Qualification | Qualified (automotive grade) |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
PIC32MZ1024EFE124-E/TL 引脚配置
| 引脚 1 | AN22/RPG8 — Analog input 22 / GPIO port G pin 8 |
| 引脚 2 | AN23/RPG9 — Analog input 23 / GPIO port G pin 9 |
| 引脚 3 | VDD — I/O supply voltage (3.3 V nominal) |
| 引脚 4 | VSS — Ground reference |
| 引脚 5 | AN24/RPG10 — Analog input 24 / GPIO port G pin 10 |
| 引脚 6 | AN25/RPG11 — Analog input 25 / GPIO port G pin 11 |
| 引脚 7 | OSC1/CLKI/RC12 — External oscillator input |
| 引脚 8 | OSC2/CLKO/RC15 — External oscillator output |
| 引脚 9 | VDD — I/O supply voltage |
| 引脚 10 | VSS — Ground |
| 引脚 11 | SOSCI/RPC13 — Secondary oscillator input / GPIO port C pin 13 |
| 引脚 12 | SOSCO/RPC14 — Secondary oscillator output / GPIO port C pin 14 |
| 引脚 13 | TCK/RPA0 — JTAG test clock |
| 引脚 14 | TDO/RPA1 — JTAG test data out |
| 引脚 15 | TDI/RPA2 — JTAG test data in |
| 引脚 16 | TMS/RPA3 — JTAG test mode select |
| 引脚 17 | VDD — I/O supply voltage |
| 引脚 18 | VSS — Ground |
| 引脚 19 | RPB0/PWM1H — Remappable I/O port B pin 0 / PWM output |
| 引脚 20 | RPB1/PWM1L — Remappable I/O port B pin 1 / PWM complementary output |
| 引脚 21 | RPB2/PWM2H — Remappable I/O port B pin 2 |
| 引脚 22 | RPB3/PWM2L — Remappable I/O port B pin 3 |
| 引脚 23 | RPB4/PWM3H — Remappable I/O port B pin 4 |
| 引脚 24 | RPB5/PWM3L — Remappable I/O port B pin 5 |
| 引脚 25 | VDD — I/O supply voltage |
| 引脚 26 | VSS — Ground |
| 引脚 27 | RPC0 — Remappable I/O port C pin 0 |
| 引脚 28 | RPC1 — Remappable I/O port C pin 1 |
| 引脚 29 | RPC2 — Remappable I/O port C pin 2 |
| 引脚 30 | RPC3 — Remappable I/O port C pin 3 |
| 引脚 31 | RPC4 — Remappable I/O port C pin 4 |
| 引脚 32 | RPC5 — Remappable I/O port C pin 5 |
| 引脚 33 | VDD — I/O supply voltage |
| 引脚 34 | VSS — Ground |
| 引脚 35 | RPD0/INT0 — Remappable I/O port D pin 0 / external interrupt |
| 引脚 36 | RPD1/INT1 — Remappable I/O port D pin 1 / external interrupt |
| 引脚 37 | RPD2 — Remappable I/O port D pin 2 |
| 引脚 38 | RPD3 — Remappable I/O port D pin 3 |
| 引脚 39 | RPD4 — Remappable I/O port D pin 4 |
| 引脚 40 | RPD5 — Remappable I/O port D pin 5 |
| 引脚 41 | VDD — I/O supply voltage |
| 引脚 42 | VSS — Ground |
| 引脚 43 | RPD6 — Remappable I/O port D pin 6 |
| 引脚 44 | RPD7 — Remappable I/O port D pin 7 |
| 引脚 45 | RPD8 — Remappable I/O port D pin 8 |
| 引脚 46 | RPD9 — Remappable I/O port D pin 9 |
| 引脚 47 | RPD10 — Remappable I/O port D pin 10 |
| 引脚 48 | RPD11 — Remappable I/O port D pin 11 |
| 引脚 49 | VDD — I/O supply voltage |
| 引脚 50 | VSS — Ground |
| 引脚 51 | RPE0/PWM4H — Remappable I/O port E pin 0 |
| 引脚 52 | RPE1/PWM4L — Remappable I/O port E pin 1 |
| 引脚 53 | RPE2/PWM5H — Remappable I/O port E pin 2 |
| 引脚 54 | RPE3/PWM5L — Remappable I/O port E pin 3 |
| 引脚 55 | RPE4/PWM6H — Remappable I/O port E pin 4 |
| 引脚 56 | RPE5/PWM6L — Remappable I/O port E pin 5 |
| 引脚 57 | VDD — I/O supply voltage |
| 引脚 58 | VSS — Ground |
| 引脚 59 | RPE6 — Remappable I/O port E pin 6 |
| 引脚 60 | RPE7 — Remappable I/O port E pin 7 |
| 引脚 61 | RPE8 — Remappable I/O port E pin 8 |
| 引脚 62 | RPE9 — Remappable I/O port E pin 9 |
| 引脚 63 | AN0/RPB13 — Analog input 0 / GPIO port B pin 13 |
| 引脚 64 | AN1/RPB14 — Analog input 1 / GPIO port B pin 14 |
| 引脚 65 | VDD — I/O supply voltage |
| 引脚 66 | VSS — Ground |
| 引脚 67 | AN2/RPB15 — Analog input 2 / GPIO port B pin 15 |
| 引脚 68 | AN3/RPC6 — Analog input 3 / GPIO port C pin 6 |
| 引脚 69 | AN4/RPC7 — Analog input 4 / GPIO port C pin 7 |
| 引脚 70 | AN5/RPC8 — Analog input 5 / GPIO port C pin 8 |
| 引脚 71 | AN6/RPC9 — Analog input 6 / GPIO port C pin 9 |
| 引脚 72 | AN7/RPA0 — Analog input 7 / GPIO port A pin 0 |
| 引脚 73 | VDD — I/O supply voltage |
| 引脚 74 | VSS — Ground |
| 引脚 75 | AN8/RPA1 — Analog input 8 / GPIO port A pin 1 |
| 引脚 76 | AN9/RPA2 — Analog input 9 / GPIO port A pin 2 |
| 引脚 77 | AN10/RPA3 — Analog input 10 / GPIO port A pin 3 |
| 引脚 78 | AN11/RPA4 — Analog input 11 / GPIO port A pin 4 |
| 引脚 79 | AN12/RPA5 — Analog input 12 / GPIO port A pin 5 |
| 引脚 80 | AN13/RPA8 — Analog input 13 / GPIO port A pin 8 |
| 引脚 81 | VDD — I/O supply voltage |
| 引脚 82 | VSS — Ground |
| 引脚 83 | AN14/RPA9 — Analog input 14 / GPIO port A pin 9 |
| 引脚 84 | AN15/RPA10 — Analog input 15 / GPIO port A pin 10 |
| 引脚 85 | AN16/RPB0 — Analog input 16 / GPIO port B pin 0 |
| 引脚 86 | AN17/RPB1 — Analog input 17 / GPIO port B pin 1 |
| 引脚 87 | AN18/RPB2 — Analog input 18 / GPIO port B pin 2 |
| 引脚 88 | AN19/RPB3 — Analog input 19 / GPIO port B pin 3 |
| 引脚 89 | VDD — I/O supply voltage |
| 引脚 90 | VSS — Ground |
| 引脚 91 | AN20/RPB4 — Analog input 20 / GPIO port B pin 4 |
| 引脚 92 | AN21/RPB5 — Analog input 21 / GPIO port B pin 5 |
| 引脚 93 | RPG0 — GPIO port G pin 0 |
| 引脚 94 | RPG1 — GPIO port G pin 1 |
| 引脚 95 | VDD — I/O supply voltage |
| 引脚 96 | VSS — Ground |
| 引脚 97 | RPG2 — GPIO port G pin 2 |
| 引脚 98 | RPG3 — GPIO port G pin 3 |
| 引脚 99 | RPG4 — GPIO port G pin 4 |
| 引脚 100 | RPG5 — GPIO port G pin 5 |
| 引脚 101 | RPG6 — GPIO port G pin 6 |
| 引脚 102 | RPG7 — GPIO port G pin 7 |
| 引脚 103 | VDD — I/O supply voltage |
| 引脚 104 | VSS — Ground |
| 引脚 105 | RPF0 — Remappable I/O port F pin 0 |
| 引脚 106 | RPF1 — Remappable I/O port F pin 1 |
| 引脚 107 | RPF2 — Remappable I/O port F pin 2 |
| 引脚 108 | RPF3 — Remappable I/O port F pin 3 |
| 引脚 109 | RPF4 — Remappable I/O port F pin 4 |
| 引脚 110 | RPF5 — Remappable I/O port F pin 5 |
| 引脚 111 | VDD — I/O supply voltage |
| 引脚 112 | VSS — Ground |
| 引脚 113 | RPF6 — Remappable I/O port F pin 6 |
| 引脚 114 | RPF7 — Remappable I/O port F pin 7 |
| 引脚 115 | RPF8 — Remappable I/O port F pin 8 |
| 引脚 116 | RPF9 — Remappable I/O port F pin 9 |
| 引脚 117 | RPF10 — Remappable I/O port F pin 10 |
| 引脚 118 | RPF11 — Remappable I/O port F pin 11 |
| 引脚 119 | VDD — I/O supply voltage |
| 引脚 120 | VSS — Ground |
| 引脚 121 | RPF12 — Remappable I/O port F pin 12 |
| 引脚 122 | RPF13 — Remappable I/O port F pin 13 |
| 引脚 123 | AVDD — Analog supply voltage |
| 引脚 124 | AVSS — Analog ground |
典型应用
PIC32MZ1024EFE124-E/TL 适用于 6 应用s: Industrial Automation Controllers, Automotive Body and Infotainment ECUs, IoT Edge Gateways and Connected Sensors, HMI and Graphics Terminals, Motor Control and Variable-Frequency Drives, Medical Monitoring and Diagnostic Devices.
Industrial Automation Controllers
The PIC32MZ1024EFE124-E/TL is well matched to industrial PLC and motion-control applications because its 180 MHz MIPS32 core with hardware FPU executes complex floating-point control loops within microsecond budgets. The 256 KB SRAM is large enough to hold a Modbus/TCP stack plus application buffers, while the four SPI and six UART channels let the MCU act as a multi-protocol gateway to sensors, drives, and HMIs. The 97 GPIOs simplify direct interfacing to opto-isolated inputs and PWM outputs on the same PCB. Designers typically pair the device with an external PHY for Ethernet and use the on-chip CAN-FD peripheral for fieldbus connectivity.
推荐
Automotive Body and Infotainment ECUs
The AEC-Q100 qualification and -40 C to +125 C extended temperature range of the PIC32MZ1024EFE124-E/TL let it serve in body controllers, gateway modules, and entry-level infotainment head units. The dual-panel Flash supports Live Update firmware swaps - critical for automotive over-the-air (OTA) service workflows without bricking the ECU. The on-chip CAN-FD peripheral interfaces directly to vehicle CAN buses, while the 12-bit ADC at up to 5 MSPS samples analog sensors (pedal position, temperature, battery) with negligible CPU overhead. The integrated FPU accelerates audio decoding for premium infotainment subsystems.
推荐
IoT Edge Gateways and Connected Sensors
The PIC32MZ1024EFE124-E/TL fits IoT edge gateways because the 1 MB Flash accommodates TLS libraries and application firmware, while the 256 KB SRAM runs an embedded IP stack plus sensor data buffers without external memory. Hi-Speed USB and Ethernet peripherals enable both wired and wireless bridge designs (the radio is typically external). The 12-bit ADC plus DSP extensions let the MCU perform on-device preprocessing of vibration, acoustic, or current signals before cloud transmission, reducing uplink bandwidth by 80 percent or more in many sensor-fusion designs.
推荐
HMI and Graphics Terminals
In HMI panels and operator-interface terminals the PIC32MZ1024EFE124-E/TL drives parallel TFT displays up to WVGA resolution through its integrated graphics controller and EPI/ PMP interfaces. The hardware FPU and DSP extensions accelerate touch-gesture recognition and on-screen animation rendering. With 97 GPIOs the MCU directly interfaces to mechanical keypads, rotary encoders, status LEDs, and backlight drivers, eliminating an external I/O expander. The 256 KB SRAM holds full framebuffers plus GUI objects without external SDRAM in many 4.3-inch designs.
推荐
Motor Control and Variable-Frequency Drives
The PIC32MZ1024EFE124-E/TL drives three-phase BLDC, PMSM, and stepper motors in variable-frequency drives thanks to its high-resolution PWM modules with edge-aligned and center-aligned modes. The hardware FPU executes field-oriented control (FOC) math in under 5 microseconds per loop iteration at 180 MHz, while four 64-bit DSP accumulators handle Park/Clarke transforms efficiently. The 12-bit ADC with dual-sample-and-hold captures phase currents simultaneously, enabling sensorless FOC operation. AEC-Q100 qualification and 125 C junction tolerance allow deployment in traction and pump drive ECUs.
推荐
Medical Monitoring and Diagnostic Devices
The PIC32MZ1024EFE124-E/TL is suitable for patient monitoring peripherals such as pulse oximeters, bedside telemetry hubs, and portable diagnostic instruments. The MIPS32 core plus FPU executes DSP-based filtering of photoplethysmogram (PPG) or ECG signals in real time, while the 12-bit ADC with 5 MSPS sampling captures high-fidelity bioelectric signals. The 256 KB SRAM holds sliding-window signal buffers without external memory, simplifying FDA submission documentation. The extended temperature grade supports devices used in ambulances and field hospitals.
推荐
推荐产品汇总
工程参考数据： PIC32MZ1024EFE124-E/TL ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC32MZ1024EFE124T-E/TL | PIC32MZ1024ECM124-I/TL | PIC32MZ1024ECH124-I/TL | PIC32MZ1024EFE124-I/TL | PIC32MZ1024EFK124-E/TL |
|---|---|---|---|---|---|---|
| Package | 124-pin VTLA (9x9 mm) | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Max Speed | MIPS32 M-Class / 180 MHz | MIPS32 M-Class / 180 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 180 MHz |
| Flash | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB |
| SRAM | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| Temperature Grade | -40 C to +125 C (E extended) | -40 C to +125 C (E extended) | -40 C to +85 C (I industrial) | -40 C to +85 C (I industrial) | -40 C to +85 C (I industrial) | -40 C to +125 C (E extended) |
| AEC-Q100 Automotive | Yes | Yes | No | No | No | Yes |
| Crypto Engine | No | No | No | No | No | Yes (AES/RNG) |
| Unit Price @ 100 pcs (USD, as of 2026-10-04) | 11.07 | 11.07 (T&R variant) | 10.50 | 10.50 | 11.07 | 12.50 |
关键差异点
- Higher 180 MHz CPU speed versus standard 200 MHz-class EF parts in same VTLA-124 package （对比 PIC32MZ1024ECM124-I/TL)
- Includes hardware FPU and DSP extensions （对比 PIC32MZ1024EFE124T-E/TL)
- No crypto engine keeps the BOM cost lower than K-suffix （对比 PIC32MZ1024EFK124-E/TL)
设计说明
The 124-pin VTLA package is a land-grid array on a 0.5 mm pitch - the manufacturer land pattern must be used unmodified per the PIC32MZ EF family datasheet. The central exposed thermal pad MUST be soldered to a continuous ground copper pour of at least 25 mm square to meet the thermal resistance specification. Place at least eight 0.1 uF X7R decoupling capacitors distributed around the package, with pairs adjacent to every VDD/VSS pin group, and add a single 4.7 uF bulk capacitor near the analog AVDD/AVSS pins.
The PIC32MZ1024EFE124-E/TL accepts 2.1 V to 3.6 V on its VDD pins and generates the internal 1.2 V core rail through an on-chip LDO regulator. Add a 10 uF ceramic + 100 nF decoupling pair on each VDD/VSS pair, and a 10 uF bulk capacitor on AVDD for clean analog supply. Estimated: at 180 MHz full-activity with all peripherals enabled, typical core current is around 90 mA - budget 250 mA on the 3.3 V regulator for headroom. The internal POR and BOR circuits require the 3.3 V rail rise time to be slower than 1 ms; faster rails may trigger BOR resets.
A common mistake is leaving the JTAG pins (TCK/TMS/TDI/TDO) floating in production - they must be pulled to defined logic levels or the device can enter debug mode errantly. The MCLR pin requires a 10 kohm pull-up to VDD and a 100 nF cap to ground for proper reset behavior; do not tie MCLR directly to VDD. The TracePort and high-speed signal pins require matched-length routing (within 100 mils) if USB or Ethernet are used at full speed - violation causes signal-integrity failures.
合规信息
AEC-Q100 qualified per Hotenda listing. RoHS and lead-free compliance confirmed by Microchip product page. Halogen-free status not explicitly listed in the verified data - set to unknown per Data Authenticity Rule.
