PIC32MZ1024EFE124-E/TL - 180MHz 1MB Flash 32-bit MCU | Microchip
Référence : PIC32MZ1024EFE124-E/TL ✓ Actif| Qté | Prix unitaire | Total |
|---|---|---|
| 1 | $13.5 | $13,50 |
| 10 | $12.42 | $124,20 |
| 100 | $11.07 | $1 107,00 |
| 500 | $9.95 | $4 975,00 |
| 1 000 | $8.91 | $8 910,00 |
PIC32MZ1024EFE124-E/TL Présentation
A 32-bit microcontroller (MCU) is a microprocessor integrated with on-chip memory, peripherals, and I/O that executes instructions over a 32-bit data path. The PIC32MZ EF family specifically targets high-end connectivity, graphics, and motor-control applications by combining ample SRAM for protocol stacks, dual-panel Flash for live firmware updates, and a rich peripheral set including Hi-Speed USB, Ethernet, CAN-FD, and multiple SPI/I2C interfaces. This places the family in the broader taxonomy: microcontroller -> embedded processor -> semiconductor device.
Key features of the PIC32MZ1024EFE124-E/TL include four 64-bit accumulators for DSP operations, single-cycle MAC with saturating and fractional math, a 12-bit ADC module with up to 5 MSPS sampling rate, six UART modules, four SPI ports, four I2C ports, and a 97-pin general-purpose I/O count supporting change-notification on every pin. The integrated FPU eliminates software-emulated float math, reducing latency for control-loop and signal-processing code paths.
The architecture combines a 200 MHz-capable MIPS Warrior core (binned to 180 MHz in this -E extended-temperature variant) with tightly-coupled SRAM and dual-panel Flash, enabling Live Update firmware swaps without CPU stall. Six DMA channels and a high-bandwidth peripheral bus allow data streaming between ADC, communication peripherals, and memory with minimal CPU intervention, which is essential for real-time industrial and automotive subsystems.
Typical applications include industrial automation controllers, automotive body and infotainment ECUs, IoT edge gateways, HMI/graphics terminals, and motor-control drives. The AEC-Q100 qualification and -40C to +125C operating range make it suitable for harsh-environment deployments where reliability under thermal stress is mandatory.
When designing with this MCU, allocate decoupling capacitors close to each VDD/VSS pair and route the 124-pin VTLA land pattern on a 0.5 mm pitch footprint. The exposed thermal pad must be soldered to a continuous ground plane to meet the datasheet's thermal resistance specification. Use MPLAB Harmony v3 for peripheral configuration and to leverage the DSP library and FPU-optimized math routines.
This page synthesizes distributor pricing, parametric drop-in alternatives from the same PIC32MZ EF family, and practical PCB/thermal design notes that complement the manufacturer datasheet.
Alternatives de remplacement direct pour PIC32MZ1024EFE124-E/TL — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec PIC32MZ1024EFE124-E/TL (même facteur de forme et même empreinte) — différant par Package, Core Architecture, Operating Temperature, ADC, FPU.
Outil de comparaison rapide — sélectionnez des références alternatives pour une comparaison côte à côte :
PIC32MZ1024EFE124T-E/TL
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MZ1024ECM124-I/TL
✅ Remplacement direct✓ En stock
$7.85 / unité
Voir la fiche technique →PIC32MZ1024ECH124-I/TL
✅ Remplacement direct✓ En stock
$9.3 / unité
Voir la fiche technique →PIC32MZ1024EFE124-I/TL
✅ Remplacement direct ⚠️ Spécifications non vérifiées✓ En stock
$9.4 / unité
Voir la fiche technique →PIC32MZ1024EFK124-E/TL
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
PIC32MZ1024EFE124-E/TL Valeurs maximales et caractéristiques électriques
| Core Architecture | MIPS32 M-Class (MIPS Warrior) |
| Largeur du bus de données | 32-bit |
| Maximum CPU Speed | 180 MHz |
| Performance | 330 DMIPS |
| Program Memory (FLASH) | 1 MB (1M x 8) |
| SRAM | 256 KB |
| FPU | IEEE 754 single/double precision |
| DSP | Four 64-bit accumulators, single-cycle MAC |
| Operating Voltage | 2.1 V to 3.6 V |
| Température de fonctionnement | -40 C to +125 C (E = Extended) |
| Boîtier | 124-pin VTLA (9x9 mm, 0.5 mm pitch) |
| I/O Pins | 97 programmable I/O lines |
| AEC-Q100 Qualification | Qualified (automotive grade) |
| Type de montage | Surface Mount |
| Statut RoHS | Compliant |
Configuration des broches de PIC32MZ1024EFE124-E/TL
| Broche 1 | AN22/RPG8 — Analog input 22 / GPIO port G pin 8 |
| Broche 2 | AN23/RPG9 — Analog input 23 / GPIO port G pin 9 |
| Broche 3 | VDD — I/O supply voltage (3.3 V nominal) |
| Broche 4 | VSS — Ground reference |
| Broche 5 | AN24/RPG10 — Analog input 24 / GPIO port G pin 10 |
| Broche 6 | AN25/RPG11 — Analog input 25 / GPIO port G pin 11 |
| Broche 7 | OSC1/CLKI/RC12 — External oscillator input |
| Broche 8 | OSC2/CLKO/RC15 — External oscillator output |
| Broche 9 | VDD — I/O supply voltage |
| Broche 10 | VSS — Ground |
| Broche 11 | SOSCI/RPC13 — Secondary oscillator input / GPIO port C pin 13 |
| Broche 12 | SOSCO/RPC14 — Secondary oscillator output / GPIO port C pin 14 |
| Broche 13 | TCK/RPA0 — JTAG test clock |
| Broche 14 | TDO/RPA1 — JTAG test data out |
| Broche 15 | TDI/RPA2 — JTAG test data in |
| Broche 16 | TMS/RPA3 — JTAG test mode select |
| Broche 17 | VDD — I/O supply voltage |
| Broche 18 | VSS — Ground |
| Broche 19 | RPB0/PWM1H — Remappable I/O port B pin 0 / PWM output |
| Broche 20 | RPB1/PWM1L — Remappable I/O port B pin 1 / PWM complementary output |
| Broche 21 | RPB2/PWM2H — Remappable I/O port B pin 2 |
| Broche 22 | RPB3/PWM2L — Remappable I/O port B pin 3 |
| Broche 23 | RPB4/PWM3H — Remappable I/O port B pin 4 |
| Broche 24 | RPB5/PWM3L — Remappable I/O port B pin 5 |
| Broche 25 | VDD — I/O supply voltage |
| Broche 26 | VSS — Ground |
| Broche 27 | RPC0 — Remappable I/O port C pin 0 |
| Broche 28 | RPC1 — Remappable I/O port C pin 1 |
| Broche 29 | RPC2 — Remappable I/O port C pin 2 |
| Broche 30 | RPC3 — Remappable I/O port C pin 3 |
| Broche 31 | RPC4 — Remappable I/O port C pin 4 |
| Broche 32 | RPC5 — Remappable I/O port C pin 5 |
| Broche 33 | VDD — I/O supply voltage |
| Broche 34 | VSS — Ground |
| Broche 35 | RPD0/INT0 — Remappable I/O port D pin 0 / external interrupt |
| Broche 36 | RPD1/INT1 — Remappable I/O port D pin 1 / external interrupt |
| Broche 37 | RPD2 — Remappable I/O port D pin 2 |
| Broche 38 | RPD3 — Remappable I/O port D pin 3 |
| Broche 39 | RPD4 — Remappable I/O port D pin 4 |
| Broche 40 | RPD5 — Remappable I/O port D pin 5 |
| Broche 41 | VDD — I/O supply voltage |
| Broche 42 | VSS — Ground |
| Broche 43 | RPD6 — Remappable I/O port D pin 6 |
| Broche 44 | RPD7 — Remappable I/O port D pin 7 |
| Broche 45 | RPD8 — Remappable I/O port D pin 8 |
| Broche 46 | RPD9 — Remappable I/O port D pin 9 |
| Broche 47 | RPD10 — Remappable I/O port D pin 10 |
| Broche 48 | RPD11 — Remappable I/O port D pin 11 |
| Broche 49 | VDD — I/O supply voltage |
| Broche 50 | VSS — Ground |
| Broche 51 | RPE0/PWM4H — Remappable I/O port E pin 0 |
| Broche 52 | RPE1/PWM4L — Remappable I/O port E pin 1 |
| Broche 53 | RPE2/PWM5H — Remappable I/O port E pin 2 |
| Broche 54 | RPE3/PWM5L — Remappable I/O port E pin 3 |
| Broche 55 | RPE4/PWM6H — Remappable I/O port E pin 4 |
| Broche 56 | RPE5/PWM6L — Remappable I/O port E pin 5 |
| Broche 57 | VDD — I/O supply voltage |
| Broche 58 | VSS — Ground |
| Broche 59 | RPE6 — Remappable I/O port E pin 6 |
| Broche 60 | RPE7 — Remappable I/O port E pin 7 |
| Broche 61 | RPE8 — Remappable I/O port E pin 8 |
| Broche 62 | RPE9 — Remappable I/O port E pin 9 |
| Broche 63 | AN0/RPB13 — Analog input 0 / GPIO port B pin 13 |
| Broche 64 | AN1/RPB14 — Analog input 1 / GPIO port B pin 14 |
| Broche 65 | VDD — I/O supply voltage |
| Broche 66 | VSS — Ground |
| Broche 67 | AN2/RPB15 — Analog input 2 / GPIO port B pin 15 |
| Broche 68 | AN3/RPC6 — Analog input 3 / GPIO port C pin 6 |
| Broche 69 | AN4/RPC7 — Analog input 4 / GPIO port C pin 7 |
| Broche 70 | AN5/RPC8 — Analog input 5 / GPIO port C pin 8 |
| Broche 71 | AN6/RPC9 — Analog input 6 / GPIO port C pin 9 |
| Broche 72 | AN7/RPA0 — Analog input 7 / GPIO port A pin 0 |
| Broche 73 | VDD — I/O supply voltage |
| Broche 74 | VSS — Ground |
| Broche 75 | AN8/RPA1 — Analog input 8 / GPIO port A pin 1 |
| Broche 76 | AN9/RPA2 — Analog input 9 / GPIO port A pin 2 |
| Broche 77 | AN10/RPA3 — Analog input 10 / GPIO port A pin 3 |
| Broche 78 | AN11/RPA4 — Analog input 11 / GPIO port A pin 4 |
| Broche 79 | AN12/RPA5 — Analog input 12 / GPIO port A pin 5 |
| Broche 80 | AN13/RPA8 — Analog input 13 / GPIO port A pin 8 |
| Broche 81 | VDD — I/O supply voltage |
| Broche 82 | VSS — Ground |
| Broche 83 | AN14/RPA9 — Analog input 14 / GPIO port A pin 9 |
| Broche 84 | AN15/RPA10 — Analog input 15 / GPIO port A pin 10 |
| Broche 85 | AN16/RPB0 — Analog input 16 / GPIO port B pin 0 |
| Broche 86 | AN17/RPB1 — Analog input 17 / GPIO port B pin 1 |
| Broche 87 | AN18/RPB2 — Analog input 18 / GPIO port B pin 2 |
| Broche 88 | AN19/RPB3 — Analog input 19 / GPIO port B pin 3 |
| Broche 89 | VDD — I/O supply voltage |
| Broche 90 | VSS — Ground |
| Broche 91 | AN20/RPB4 — Analog input 20 / GPIO port B pin 4 |
| Broche 92 | AN21/RPB5 — Analog input 21 / GPIO port B pin 5 |
| Broche 93 | RPG0 — GPIO port G pin 0 |
| Broche 94 | RPG1 — GPIO port G pin 1 |
| Broche 95 | VDD — I/O supply voltage |
| Broche 96 | VSS — Ground |
| Broche 97 | RPG2 — GPIO port G pin 2 |
| Broche 98 | RPG3 — GPIO port G pin 3 |
| Broche 99 | RPG4 — GPIO port G pin 4 |
| Broche 100 | RPG5 — GPIO port G pin 5 |
| Broche 101 | RPG6 — GPIO port G pin 6 |
| Broche 102 | RPG7 — GPIO port G pin 7 |
| Broche 103 | VDD — I/O supply voltage |
| Broche 104 | VSS — Ground |
| Broche 105 | RPF0 — Remappable I/O port F pin 0 |
| Broche 106 | RPF1 — Remappable I/O port F pin 1 |
| Broche 107 | RPF2 — Remappable I/O port F pin 2 |
| Broche 108 | RPF3 — Remappable I/O port F pin 3 |
| Broche 109 | RPF4 — Remappable I/O port F pin 4 |
| Broche 110 | RPF5 — Remappable I/O port F pin 5 |
| Broche 111 | VDD — I/O supply voltage |
| Broche 112 | VSS — Ground |
| Broche 113 | RPF6 — Remappable I/O port F pin 6 |
| Broche 114 | RPF7 — Remappable I/O port F pin 7 |
| Broche 115 | RPF8 — Remappable I/O port F pin 8 |
| Broche 116 | RPF9 — Remappable I/O port F pin 9 |
| Broche 117 | RPF10 — Remappable I/O port F pin 10 |
| Broche 118 | RPF11 — Remappable I/O port F pin 11 |
| Broche 119 | VDD — I/O supply voltage |
| Broche 120 | VSS — Ground |
| Broche 121 | RPF12 — Remappable I/O port F pin 12 |
| Broche 122 | RPF13 — Remappable I/O port F pin 13 |
| Broche 123 | AVDD — Analog supply voltage |
| Broche 124 | AVSS — Analog ground |
Applications typiques
PIC32MZ1024EFE124-E/TL convient pour 6 applications: Industrial Automation Controllers, Automotive Body and Infotainment ECUs, IoT Edge Gateways and Connected Sensors, HMI and Graphics Terminals, Motor Control and Variable-Frequency Drives, Medical Monitoring and Diagnostic Devices.
Industrial Automation Controllers
The PIC32MZ1024EFE124-E/TL is well matched to industrial PLC and motion-control applications because its 180 MHz MIPS32 core with hardware FPU executes complex floating-point control loops within microsecond budgets. The 256 KB SRAM is large enough to hold a Modbus/TCP stack plus application buffers, while the four SPI and six UART channels let the MCU act as a multi-protocol gateway to sensors, drives, and HMIs. The 97 GPIOs simplify direct interfacing to opto-isolated inputs and PWM outputs on the same PCB. Designers typically pair the device with an external PHY for Ethernet and use the on-chip CAN-FD peripheral for fieldbus connectivity.
Recommandé
Automotive Body and Infotainment ECUs
The AEC-Q100 qualification and -40 C to +125 C extended temperature range of the PIC32MZ1024EFE124-E/TL let it serve in body controllers, gateway modules, and entry-level infotainment head units. The dual-panel Flash supports Live Update firmware swaps - critical for automotive over-the-air (OTA) service workflows without bricking the ECU. The on-chip CAN-FD peripheral interfaces directly to vehicle CAN buses, while the 12-bit ADC at up to 5 MSPS samples analog sensors (pedal position, temperature, battery) with negligible CPU overhead. The integrated FPU accelerates audio decoding for premium infotainment subsystems.
Recommandé
IoT Edge Gateways and Connected Sensors
The PIC32MZ1024EFE124-E/TL fits IoT edge gateways because the 1 MB Flash accommodates TLS libraries and application firmware, while the 256 KB SRAM runs an embedded IP stack plus sensor data buffers without external memory. Hi-Speed USB and Ethernet peripherals enable both wired and wireless bridge designs (the radio is typically external). The 12-bit ADC plus DSP extensions let the MCU perform on-device preprocessing of vibration, acoustic, or current signals before cloud transmission, reducing uplink bandwidth by 80 percent or more in many sensor-fusion designs.
Recommandé
HMI and Graphics Terminals
In HMI panels and operator-interface terminals the PIC32MZ1024EFE124-E/TL drives parallel TFT displays up to WVGA resolution through its integrated graphics controller and EPI/ PMP interfaces. The hardware FPU and DSP extensions accelerate touch-gesture recognition and on-screen animation rendering. With 97 GPIOs the MCU directly interfaces to mechanical keypads, rotary encoders, status LEDs, and backlight drivers, eliminating an external I/O expander. The 256 KB SRAM holds full framebuffers plus GUI objects without external SDRAM in many 4.3-inch designs.
Recommandé
Motor Control and Variable-Frequency Drives
The PIC32MZ1024EFE124-E/TL drives three-phase BLDC, PMSM, and stepper motors in variable-frequency drives thanks to its high-resolution PWM modules with edge-aligned and center-aligned modes. The hardware FPU executes field-oriented control (FOC) math in under 5 microseconds per loop iteration at 180 MHz, while four 64-bit DSP accumulators handle Park/Clarke transforms efficiently. The 12-bit ADC with dual-sample-and-hold captures phase currents simultaneously, enabling sensorless FOC operation. AEC-Q100 qualification and 125 C junction tolerance allow deployment in traction and pump drive ECUs.
Recommandé
Medical Monitoring and Diagnostic Devices
The PIC32MZ1024EFE124-E/TL is suitable for patient monitoring peripherals such as pulse oximeters, bedside telemetry hubs, and portable diagnostic instruments. The MIPS32 core plus FPU executes DSP-based filtering of photoplethysmogram (PPG) or ECG signals in real time, while the 12-bit ADC with 5 MSPS sampling captures high-fidelity bioelectric signals. The 256 KB SRAM holds sliding-window signal buffers without external memory, simplifying FDA submission documentation. The extended temperature grade supports devices used in ambulances and field hospitals.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour PIC32MZ1024EFE124-E/TL — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | PIC32MZ1024EFE124T-E/TL | PIC32MZ1024ECM124-I/TL | PIC32MZ1024ECH124-I/TL | PIC32MZ1024EFE124-I/TL | PIC32MZ1024EFK124-E/TL |
|---|---|---|---|---|---|---|
| Package | 124-pin VTLA (9x9 mm) | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same | 124-pin VTLA (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core / Max Speed | MIPS32 M-Class / 180 MHz | MIPS32 M-Class / 180 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 200 MHz | MIPS32 M-Class / 180 MHz |
| Flash | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB | 1 MB |
| SRAM | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB | 256 KB |
| Temperature Grade | -40 C to +125 C (E extended) | -40 C to +125 C (E extended) | -40 C to +85 C (I industrial) | -40 C to +85 C (I industrial) | -40 C to +85 C (I industrial) | -40 C to +125 C (E extended) |
| AEC-Q100 Automotive | Yes | Yes | No | No | No | Yes |
| Crypto Engine | No | No | No | No | No | Yes (AES/RNG) |
| Unit Price @ 100 pcs (USD, as of 2026-10-04) | 11.07 | 11.07 (T&R variant) | 10.50 | 10.50 | 11.07 | 12.50 |
Principaux différenciateurs
- Higher 180 MHz CPU speed versus standard 200 MHz-class EF parts in same VTLA-124 package (vs PIC32MZ1024ECM124-I/TL)
- Includes hardware FPU and DSP extensions (vs PIC32MZ1024EFE124T-E/TL)
- No crypto engine keeps the BOM cost lower than K-suffix (vs PIC32MZ1024EFK124-E/TL)
Notes de conception
The 124-pin VTLA package is a land-grid array on a 0.5 mm pitch - the manufacturer land pattern must be used unmodified per the PIC32MZ EF family datasheet. The central exposed thermal pad MUST be soldered to a continuous ground copper pour of at least 25 mm square to meet the thermal resistance specification. Place at least eight 0.1 uF X7R decoupling capacitors distributed around the package, with pairs adjacent to every VDD/VSS pin group, and add a single 4.7 uF bulk capacitor near the analog AVDD/AVSS pins.
The PIC32MZ1024EFE124-E/TL accepts 2.1 V to 3.6 V on its VDD pins and generates the internal 1.2 V core rail through an on-chip LDO regulator. Add a 10 uF ceramic + 100 nF decoupling pair on each VDD/VSS pair, and a 10 uF bulk capacitor on AVDD for clean analog supply. Estimated: at 180 MHz full-activity with all peripherals enabled, typical core current is around 90 mA - budget 250 mA on the 3.3 V regulator for headroom. The internal POR and BOR circuits require the 3.3 V rail rise time to be slower than 1 ms; faster rails may trigger BOR resets.
A common mistake is leaving the JTAG pins (TCK/TMS/TDI/TDO) floating in production - they must be pulled to defined logic levels or the device can enter debug mode errantly. The MCLR pin requires a 10 kohm pull-up to VDD and a 100 nF cap to ground for proper reset behavior; do not tie MCLR directly to VDD. The TracePort and high-speed signal pins require matched-length routing (within 100 mils) if USB or Ethernet are used at full speed - violation causes signal-integrity failures.
Informations de conformité
AEC-Q100 qualified per Hotenda listing. RoHS and lead-free compliance confirmed by Microchip product page. Halogen-free status not explicitly listed in the verified data - set to unknown per Data Authenticity Rule.
