SI3227-E-GQ - Dual-Channel SLIC/CODEC, 3.3V, 64-TQFP
料号: SI3227-E-GQ ✓ 量产中SI3227-E-GQ 概述
A SLIC, or Subscriber Line Interface Circuit, is the analog-facing section of a telephone line interface. It converts between a line-referenced analog voice signal and a digital PCM stream, while a companion CODEC handles signal conversion and voice processing. In the broader semiconductor hierarchy, the SI3227-E-GQ belongs to the interface IC family and then to the telecommunications interface category, combining analog line access, digital logic, and power-conversion control in one device.
Key features include two line circuits, 64 terminations, a 3.3 V operating supply, and support for GCI, PCM, and SPI interfaces. The integrated dual DC-DC controllers reduce the number of separate power-management components required in a line-card design. Its 64-pin TQFP package provides enough pin count for two complete channels and their associated control, interface, biasing, and supply connections, while supporting standard surface-mount assembly methods.
The device is intended for telecom access equipment where a compact two-channel solution offers a better channel-density tradeoff than discrete SLIC and codec arrangements. Split supply rails created by the internal DC-DC controllers can help separate sensitive analog and digital functions, although component selection and layout remain the responsibility of the system designer. The SI3227-E-GQ also supports lead-free assembly according to its distributor listing.
Typical uses include Voice-over-IP endpoint hardware, analog terminal adapters, digital line-card equipment, embedded telephony controllers, and industrial voice gateways. Two integrated channels allow one package to serve both sides of a two-line terminal or a single line pair on a multi-port access board, reducing board area when compared with two separate single-channel devices.
The primary design trade-off is channel integration versus flexibility. Combining two SLIC channels, codec functions, digital interfaces, and DC-DC control simplifies the bill of materials, but the layout must carefully separate line-referenced analog routing from high-speed digital signals and sensitive supply nodes. Confirm absolute maximum ratings, line-state impedance requirements, and interface timing against the manufacturer datasheet before releasing a production layout.
This page organizes the device specifications, pin-compatible family options, application guidance, and design considerations into one engineering reference. It also identifies the electrical and mechanical details that should be checked during PCB bring-up and production qualification.
直接替换替代料: SI3227-E-GQ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
SI3227-E-FQ
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →SI3227-E-FQR
✅ 直接替换📋 参考替代料(不在目录中)
SI3227-GQ
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
SI3227-E-GQR
✅ 直接替换📋 参考替代料(不在目录中)
SI3227-GQR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
SI3227-E-GQ 规格参数
| Product Type | Dual-channel wideband SLIC/CODEC |
| Number of Channels | 2 circuits |
| Line Terminations | 64 terminations |
| 电源电压 | 3.3 V |
| Current | 45 mA |
| Gain | 60 dB |
| Digital Interface | GCI, PCM, SPI |
| Integrated Power Control | Dual DC-DC controllers |
| 封装 | 64-pin TQFP |
| 安装类型 | Surface Mount |
| Termination Style | Lead-free |
| Line Interface Type | Telecom Interface |
| Codec Functions | Dual-channel SLIC/CODEC |
SI3227-E-GQ 64-pin tqfp 引脚配置指南
SI3227-E-GQ(64-pin tqfp 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: SI3227-E-GQ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SI3227-E-GQ 适用于 6 应用s: Voice-over-IP Terminal Interface, Analog Terminal Adapter, Multi-Port Voice Gateway, Embedded Telephony Controller, Digital Line Card Equipment, Industrial Voice Communication Terminal.
Voice-over-IP Terminal Interface
The SI3227-E-GQ fits a two-line Voice-over-IP terminal because it combines two SLIC/CODEC channels with GCI, PCM, and SPI connectivity in one 64-pin TQFP device. Its 3.3 V operation aligns with many embedded host platforms, while the dual DC-DC controllers help organize the analog and digital supply domains. The integrated topology can reduce the number of separate interface components compared with a discrete SLIC, codec, and converter arrangement. Designers should still allocate separate board areas for line-referenced analog routing and digital control signals.
推荐
Analog Terminal Adapter
The SI3227-E-GQ is appropriate for an analog terminal adapter that must terminate two telephone lines while connecting to a digital controller. Two integrated circuits reduce the component count and board area needed for dual-channel access, and the 64 terminations support dense line-interface layouts. GCI and PCM provide established data paths for voice transport and control, while SPI can simplify device configuration. The PCB must preserve the separation between external line networks and low-level digital circuitry.
推荐
Multi-Port Voice Gateway
A multi-port voice gateway can use the SI3227-E-GQ when each board must handle two line channels without allocating separate single-channel packages. Its 3.3 V supply, 45 mA listed current, and integrated dual DC-DC controllers support compact channel-dense designs. The 64-pin TQFP package allows several devices to be placed on a line card while leaving controlled routing channels between them. For each channel, the designer must provide suitable external protection, matching, and line-access networks according to the target application.
推荐
Embedded Telephony Controller
The SI3227-E-GQ can serve as the analog line front end of an embedded telephony controller that exchanges PCM voice data with a digital processor. Its dedicated GCI, PCM, and SPI interfaces support both traffic and configuration paths, while the dual-channel architecture reduces the number of line-driver blocks needed on the board. The 3.3 V operating supply simplifies integration with modern embedded logic. Firmware and hardware teams should confirm channel timing, framing, and control signaling against the manufacturer interface documentation.
推荐
Digital Line Card Equipment
The SI3227-E-GQ is suited to digital line-card equipment requiring two subscriber-line interfaces and a compact mixed-signal package. Its 64 terminations and dual DC-DC controllers are valuable where line density and component count are both important. GCI can support a multichannel interface arrangement while PCM carries individual voice channels to the system controller. Layout quality remains critical because high-speed digital activity and line-referenced analog nodes share the same package and require disciplined return-path planning.
推荐
Industrial Voice Communication Terminal
Industrial voice terminals that connect legacy analog equipment to an Ethernet or embedded control network can use the SI3227-E-GQ for the line-facing section. The dual-channel arrangement supports two analog endpoints in one package, and the 45 mA listed operating current suits compact embedded systems. Its 3.3 V supply and SPI control path simplify connection to a host controller. Use external surge protection and isolation strategies appropriate to the line exposure, and confirm operating-temperature requirements for the deployment environment.
推荐
推荐产品汇总
工程参考数据: SI3227-E-GQ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SI3227-E-FQ | SI3227-E-FQR | SI3227-GQ | SI3227-E-GQR | SI3227-GQR |
|---|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP | 64-pin TQFP |
关键差异点
- Two complete line channels in one package (对比 SI3227-E-FQR)
- Single-device integration of line access and digital control (对比 SI3227-GQ)
- 3.3 V integration for embedded telecom systems (对比 SI3227-E-GQR)
设计说明
Separate line-referenced analog traces from GCI, PCM, and SPI routing before they approach the device. Keep external termination, protection, and matching components close to their associated pins, and avoid routing digital clock or control signals beneath line-network nodes. Provide continuous return paths and use the manufacturer's recommended ground-plane arrangement to minimize coupling between the two integrated channels.
Estimated: for a 3.3 V rail at the listed 45 mA operating current, the device-side input power is approximately 0.15 W before external converter and line-driver losses are included. Actual dissipated power depends on activity, channel state, and the external DC-DC implementation, so use the manufacturer thermal data and measured channel loading for the final enclosure and copper-area assessment.
Do not treat the GQ, GQR, FQ, and FQR order codes as electrically interchangeable without checking the family revision. The GQ and GQR distinction includes reel handling, while the E and F codes may carry revision-level differences. Confirm interface timing, absolute maximum ratings, line-impedance behavior, package orientation, and component recommendations in the manufacturer datasheet before releasing a substitution.
合规信息
The distributor listing identifies SI3227-E-FQR as lead-free. RoHS, REACH, halogen-free, and conflict-minerals declarations require confirmation in the manufacturer compliance documentation or current material declaration. AEC-Q100 status is not applicable to a telecom interface IC unless the manufacturer offers an automotive-qualified variant.