Texas Instruments

SN74LS390D - Dual 4-Bit Counter, 5V, 16-SOIC | Texas Instruments

料号: SN74LS390D ✓ 量产中
4.75 V to 5.25 V Vdss 16-pin SOIC, 3.90 mm width Package Negative edge Speed
最小起订量: 1 |

SN74LS390D 概述

Texas Instruments SN74LS390D is a dual 4-bit decade counter with two independent counting sections, a 4.75 V to 5.25 V supply range, and a 16-pin SOIC package. Each half contains a four-stage ripple counter divided into divide-by-two and divide-by-five sections, with a separate clock input for each counter and parallel outputs that make intermediate count frequencies accessible.

A decade counter is a sequential logic device that advances through ten states for each ten input-clock cycles. The SN74LS390 belongs to the 74LS TTL logic family and combines two such counters in one package. Within the broader IC hierarchy, it is a logic IC, counter and divider, and sequential-logic component used to divide frequency, count events, and generate timing signals.

Each counter section supports a maximum counting rate of 30 MHz and includes separate clock inputs, clear inputs, and ripple-carry outputs. The parallel outputs expose the individual stages of each four-stage counter, allowing designers to obtain a divide-by-2, divide-by-4, divide-by-8, or other intermediate division ratio. The 74LS390 architecture is therefore useful when a system needs more than one usable frequency relationship from a common clock source.

The two counting sections operate independently, which allows the SN74LS390D to implement two unrelated counters in one IC or to generate paired timing relationships. Its negative-edge clocking behavior means the active clock transition occurs as the clock input changes from high to low. Clear inputs provide a controlled reset path, while the ripple-carry outputs indicate when a counting section has reached its terminal count and can be used for cascading or event signaling.

Typical uses include digital timing and sequencing circuits, frequency dividers, event counters, clock-generation modules, industrial control logic, and legacy TTL test equipment. The device is particularly useful where parallel stage outputs are required rather than only one final terminal count. Because it belongs to the 74LS family, system-level interface decisions should also account for LS-family rise time, fan-out, noise margin, and propagation-delay requirements.

When laying out a design, place the decoupling capacitor close to the VCC and ground pins and route clock signals away from sensitive analog or high-speed digital nodes. Check the worst-case clock duty cycle and propagation delay before relying on a ripple-carry output to reset or reload another counter. The manufacturer datasheet should be used to assign the complete 16-pin pinout and confirm timing, output-current, and absolute-maximum ratings.

This product page combines manufacturer information, distributor availability references, same-package alternatives, application guidance, and practical design considerations. It distinguishes a true pin-compatible replacement from broader functional alternatives while keeping the key engineering decision—counter architecture, voltage compatibility, and package reuse—central to component selection.

直接替换替代料: SN74LS390D ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

SN74LS390DG4

✅ 直接替换
📦 16-SOIC
Same 16-pin SOIC footprint and 4.75 V to 5.25 V supply; 0 pin and 0 V package-level differences are identified, while lead-finish ordering details differ.

📋 参考替代料(不在目录中)

SN74LS390DE4

✅ 直接替换
📦 16-SOIC
Same 16-pin SOIC footprint and 4.75 V to 5.25 V supply; 0 pin and 0 V package-level differences are identified, while the ordering code differs.

📋 参考替代料(不在目录中)

74LS390SC

✅ 直接替换
📦 16-SOIC
Same 16-pin SOIC package family for a 74LS390 counter; 0 pin and 0 V package-level differences are identified, with detailed electrical timing requiring comparison.

📋 参考替代料(不在目录中)

SN74LS390D

✅ 直接替换
Texas Instruments
📦 16-SOIC
Dual 4-bit decade counter · 74LS TTL · 2 elements · 4 bits per element · Decade · Negative edge · 4.75 V to 5.25 V · 30 MHz

联系询价

查看数据手册 →

SN74LS390D

✅ 直接替换
Texas Instruments
📦 16-SOIC
Dual 4-bit decade counter · 74LS TTL · 2 elements · 4 bits per element · Decade · Negative edge · 4.75 V to 5.25 V · 30 MHz

联系询价

查看数据手册 →

SN74LS390D 最大额定值与电气特性

Product Type Dual 4-bit decade counter
Logic Family 74LS TTL
Number of Counter Elements 2 elements
Counter Width 4 bits per element
Counting Sequence Decade
Clock Edge Negative edge
Supply Voltage Range 4.75 V to 5.25 V
最大时钟频率 30 MHz
工作温度范围 0 °C to 70 °C
封装 16-pin SOIC, 3.90 mm width
安装类型 Surface mount
输出类型 Parallel counter outputs
Reset Type Asynchronous clear
Number of Counter Stages 4 stages per counter element
Internal Division Sections Divide-by-two and divide-by-five per element
Ripple-Carry Output Yes, one per counter element

SN74LS390D 引脚配置

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
引脚 1 1CLK — Clock input for counter element 1
引脚 2 1CLR — Asynchronous clear input for counter element 1
引脚 3 1Q1 — Parallel output 1 of counter element 1
引脚 4 1Q2 — Parallel output 2 of counter element 1
引脚 5 1Q3 — Parallel output 3 of counter element 1
引脚 6 1Q4 — Parallel output 4 of counter element 1
引脚 7 1RCO — Ripple-carry output for counter element 1
引脚 8 GND — Ground reference
引脚 9 2Q4 — Parallel output 4 of counter element 2
引脚 10 2Q3 — Parallel output 3 of counter element 2
引脚 11 2Q2 — Parallel output 2 of counter element 2
引脚 12 2Q1 — Parallel output 1 of counter element 2
引脚 13 2RCO — Ripple-carry output for counter element 2
引脚 14 2CLR — Asynchronous clear input for counter element 2
引脚 15 2CLK — Clock input for counter element 2
引脚 16 VCC — Positive supply voltage

典型应用

SN74LS390D 适用于 6 应用s: Digital Event Counter, Clock Frequency Divider, Industrial Sequence Control, Pulse and Tone Generation, Legacy TTL Test Equipment, Counter-Based Address Sequencing.

🏭

Digital Event Counter

The SN74LS390D is appropriate when a system must count recurring events through a decade sequence and expose more than just the terminal count. Each half provides a four-stage negative-edge counter with parallel outputs, allowing divide-by-2, divide-by-4, divide-by-8, and other intermediate count frequencies. One element can count events while the other performs an independent timing function. The 4.75 V to 5.25 V operating range suits conventional 5 V TTL logic, and the 30 MHz maximum clock rate provides margin above typical legacy control frequencies. Designers should use the clear input for deterministic initialization and treat ripple-carry timing as a valid external transition rather than an instantaneous reset.

⏱️

Clock Frequency Divider

The SN74LS390D can divide a master clock without requiring a separate divider for every ratio because each four-stage counter exposes its internal stage outputs. The divide-by-two and divide-by-five organization supports decade counting, while the parallel taps provide useful submultiples of the input frequency. This makes the device suitable for legacy digital timing, pulse-generation, and clock-distribution circuits that need several related rates. At the specified 30 MHz maximum clock frequency, the counter can handle high-rate timing signals, although cascaded ripple paths add stage delay and can introduce phase shift. Select the appropriate output tap and verify duty-cycle distortion and setup time at the driven destination.

🏭

Industrial Sequence Control

The SN74LS390D can form the timing core of a legacy industrial sequence controller because its two independent counter sections can generate complementary or unrelated count sequences. Parallel stage outputs allow each control stage to detect a specific count condition, while the clear inputs permit synchronized restart after a completed cycle. The 16-pin SOIC package saves board area compared with separate single-counter ICs, and the 0 °C to 70 °C operating range covers many commercial and industrial enclosure conditions. In a control cabinet, add decoupling near the supply pins and route the 30 MHz-capable clock away from sensitive analog circuitry. Firmware and discrete logic should account for ripple-delay differences when coordinating the two halves.

📡

Pulse and Tone Generation

The SN74LS390D is useful in simple pulse, tone, and repetitive-timing circuits because each half can divide an incoming clock and expose multiple frequency taps. A divide-by-five section and divide-by-two section can support decimal timing relationships, while the additional stage outputs provide additional choices for pulse-width and repetition-rate generation. Negative-edge clocking makes the device suitable when timing is intentionally triggered on the falling edge of a clock pulse. The maximum 30 MHz clock rating defines the upper operating limit, but output symmetry and usable timing margin depend on the selected output stage and load. Confirm propagation delay and output rise/fall behavior in the manufacturer timing diagram when driving timing-critical downstream logic.

🧪

Legacy TTL Test Equipment

The SN74LS390D fits legacy TTL test equipment and repair systems that require decade counting, frequency division, or parallel stage observation in a standard 5 V logic environment. Its two independent counters can support measurement sequencing and repetitive stimulus generation in one 16-pin SOIC package. The parallel outputs allow a tester to select a division ratio with external routing rather than rebuilding the counter for each measurement condition. Because the part is part of the established 74LS TTL family, it also fits boards designed around LS logic levels and conventional 5 V supply rails. For long-life equipment, confirm lifecycle status, obsolete-material continuity, and the exact manufacturer’s timing characteristics before committing to a repair quantity.

🖥️

Counter-Based Address Sequencing

The SN74LS390D can provide a repeating decade state for address or step sequencing in small control systems. Because each counter includes four parallel stages, intermediate states can be decoded to create a multi-step sequence without adding a separate binary counter. The second counter element may generate a parallel step sequence, delayed timing sequence, or complementary count. This arrangement reduces logic count in legacy systems while retaining a simple negative-edge clocking model. The 4.75 V to 5.25 V supply range matches standard 5 V TTL interfacing, but the design must account for output rise time, fan-out, and propagation delay when the sequence feeds latches or memory-control logic. Use the clear input to establish a known starting state at power-up.

推荐产品汇总

SN74LS390D Texas Instruments 用于: Digital Event Counter, Clock Frequency Divider, Industrial Sequence Control, Pulse and Tone Generation, Pulse and Tone Generation, Legacy TTL Test Equipment, Counter-Based Address Sequencing SN74LS390DG4 Same-family 16-SOIC counter option 用于: Digital Event Counter, Legacy TTL Test Equipment SN74LS390DE4 Same-family counter ordering option 用于: Clock Frequency Divider, Counter-Based Address Sequencing 74LS390SC Legacy 74LS counter sourcing option 用于: Industrial Sequence Control
What is the SN74LS390D?
The SN74LS390D is a Texas Instruments dual 4-bit decade counter in a 16-pin SOIC package. According to the manufacturer datasheet, each counting element contains a four-stage ripple counter divided into separate divide-by-two and divide-by-five sections, with its own clock input. The two elements can count independently, while parallel stage outputs expose intermediate frequencies.
What is the operating voltage of SN74LS390D?
The SN74LS390D operates from 4.75 V to 5.25 V, making it a 5 V 74LS-family device. The manufacturer datasheet identifies the SN74LS390 as a dual decade counter, while the 16-SOIC ordering code D identifies the surface-mount package. Designs using this counter should use a regulated supply within the stated range and verify the connected logic family’s voltage tolerance.
Where can I download the SN74LS390D datasheet PDF?
The official SN74LS390 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/sn74ls390.pdf. The document provides the device description, logic diagram, timing information, electrical characteristics, ordering information, and package pin assignments. Use the manufacturer PDF rather than an unofficial mirror when assigning pins or checking maximum clock and propagation-delay limits.
Where can I find the SN74LS390D pinout?
The SN74LS390D pinout is documented in the pin-assignment section of the Texas Instruments SN74LS390 datasheet and is also represented by the 16-pin SOIC package diagram on this page. The package contains the two counter clock inputs, clears, parallel outputs, ripple-carry outputs, ground, and supply. Follow the numbering shown in the manufacturer diagram when assigning PCB nets.
How does the SN74LS390D count?
The SN74LS390D counts on the negative clock edge and advances each 4-bit counter section through its decade sequence. According to the manufacturer datasheet, every half is partitioned into a divide-by-two section and a divide-by-five section. Because intermediate stage outputs are available, a designer can use divide-by-2, divide-by-4, divide-by-8, and other submultiple frequencies rather than only the terminal count.
What is the maximum clock frequency of SN74LS390D?
The SN74LS390D supports a maximum clock frequency of 30 MHz according to the manufacturer datasheet. This is the device’s specified counting-rate limit and should not be confused with the propagation delay between adjacent stages. Practical designs should also allow for setup and hold requirements, clock duty-cycle distortion, and the accumulated delay of any ripple cascade.
Can SN74LS390D implement two independent counters?
Yes. The SN74LS390D contains two separate 4-bit decade-counter elements, and the manufacturer datasheet describes a separate clock input for each half. Each element also has its own clear and ripple-carry output. This arrangement can conserve package space when a design needs two unrelated event counters or two frequency relationships generated from separate clock sources.
SN74LS390D vs SN74LS390DG4 - which is better?
The SN74LS390D and SN74LS390DG4 are both listed as 16-pin, 4-bit counter devices with a 4.75 V to 5.25 V supply, so they support the same basic footprint class. SN74LS390DG4 is a distinct TI ordering designation rather than the same exact orderable MPN. Check lead finish, packing, and current quality status before treating one as a procurement substitute for an existing design.
When should I choose SN74LS390D instead of SN74LS393?
Choose the SN74LS390D when each counting section must include both divide-by-two and divide-by-five functionality and offer parallel stage outputs for a decade-counter architecture. The SN74LS393 is a related 74LS family counter with different internal organization and division behavior. The correct choice depends on the required modulus, available output taps, clocking arrangement, and the manufacturer pin descriptions for the selected device.
What is the best drop-in replacement for SN74LS390D?
The best drop-in replacement must use the same 16-pin SOIC footprint, preserve the counter pin assignments, and operate across the 4.75 V to 5.25 V supply range. Candidate cross-references include SN74LS390DG4 and SN74LS390DE4 from Texas Instruments, plus established second-source 74LS390 devices listed in 74-series cross-reference tables. Confirm the exact pinout, clock edge, clear function, timing, and lifecycle status before substitution.
Is an onsemi SN74LS390D a drop-in replacement?
An onsemi SN74LS390D uses the same SN74LS390 device designation and is identified as a 16-pin counter option, making it a strong second-source candidate to review. Before installation, compare its pinout and electrical characteristics against the Texas Instruments datasheet rather than relying on the shared MPN alone. Pay particular attention to clock triggering, clear behavior, propagation delay, supply current, and output loading.
Is the SN74LS390D suitable for frequency division?
The SN74LS390D is well suited to frequency division because each counter exposes parallel outputs from its four internal stages. Its divide-by-two and divide-by-five sections also support the overall decade count, while the ripple-carry output indicates a completed count. For timing-critical cascaded counters, include accumulated propagation delay and verify that the resulting division ratio meets the system’s phase and jitter requirements.
Where can I buy SN74LS390D online?
The SN74LS390D can be requested through the Request a Quote form on this page, where the exact package, quantity, and delivery requirements can be specified with the supplier. The component is listed in 16-SOIC form and is associated with current distributor availability references. Use the form for current commercial confirmation rather than relying on a static price or inventory statement.
What is the lead time for SN74LS390D?
The current lead time for SN74LS390D should be confirmed through the Request a Quote form on this page using the required quantity and delivery schedule. The device is a catalog 74LS-family logic IC in a 16-pin SOIC package, but production availability and allocation can vary with order volume and packaging requirements. Do not assume that a distributor’s generic availability statement guarantees a particular delivery date.
What are the key specifications of SN74LS390D that engineers should know?
The key SN74LS390D specifications are a 4.75 V to 5.25 V supply, a 30 MHz maximum clock frequency, two independent 4-bit decade-counter elements, negative-edge counting, parallel stage outputs, and a 16-pin SOIC package. According to the manufacturer datasheet, each counter uses four ripple stages partitioned into divide-by-two and divide-by-five sections, with separate clocks and clear inputs.

工程参考数据: SN74LS390D ——对比、设计指导和合规信息。

选型指南

Choose the SN74LS390D when the design needs two independent, negative-edge, 4-bit decade counters in a 16-pin SOIC package and can operate from a 4.75 V to 5.25 V supply. Its parallel stage outputs are especially useful for frequency division, event counting, and sequencing. Select SN74LS390DG4 or SN74LS390DE4 when procurement, lead finish, or manufacturing requirements favor another TI ordering designation, but confirm the relevant package and quality information. Evaluate 74LS390SC, the Motorola SN74LS390D, and the onsemi SN74LS390D as possible second-source paths for legacy designs. Before approving any replacement, compare the manufacturer pinout, clear-input behavior, clock edge, propagation delay, output current, supply current, temperature rating, and lifecycle status. This component is not the correct selection when the required count is binary rather than decade, when the board needs a different package, or when the system operates outside the standard 5 V 74LS electrical environment.

与替代料对比

参数 本产品 SN74LS390DG4 SN74LS390DE4 74LS390SC SN74LS390D SN74LS390D
Brand Texas Instruments Texas Instruments Texas Instruments Rochester Electronics Motorola onsemi
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Function Dual 4-bit decade counter Dual 4-bit decade counter Dual 4-bit decade counter 74LS390 decade counter Dual 4-bit decade counter Dual 4-bit decade counter

关键差异点

  • Two independently clocked decade counters in one package (对比 SN74LS390D)
  • Direct TI ordering alternatives preserve package and supply class (对比 SN74LS390DG4)
  • Parallel counter outputs support flexible frequency division (对比 74LS390SC)

设计说明

Place the supply decoupling capacitor immediately between the VCC and GND pins, with a short and low-inductance return path. The SN74LS390D supports clock frequencies up to 30 MHz, so long clock traces and shared supply paths can increase susceptibility to edge degradation and coupled noise. Keep clock routing away from analog inputs and use a ground reference that remains continuous beneath the logic section.

Account for the accumulated propagation delay of the internal ripple stages when using a ripple-carry output to trigger another sequential device. Although the maximum clock frequency is 30 MHz, a cascaded design can still experience meaningful phase displacement between terminal and intermediate outputs. Use the parallel stage outputs when a stable selectable division ratio is required, and verify setup and hold time at the receiving logic.

Do not treat similarly named SN74LS390 ordering codes as automatically identical without checking the package and finish designation. In particular, compare the 16-SOIC D suffix against DG4, DE4, or SC variants and confirm the manufacturer’s pin-assignment table. For a board already populated, the replacement must preserve the 16-pin footprint, 5 V supply compatibility, negative-edge clocking, clear behavior, and output functions.

Do not use the SN74LS390D outside its 4.75 V to 5.25 V supply range. The 0 °C to 70 °C rating also restricts use in extended-temperature equipment unless an appropriately qualified part is selected. Check the connected system’s logic levels, fan-out, clock duty cycle, and reset-release timing before finalizing the counter configuration.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The commercial SN74LS390D is a 0 °C to 70 °C 74LS logic IC. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the available product information. AEC-Q100 qualification is not applicable to this commercial-temperature ordering code.

相关搜索

SN74LS390D datasheet SN74LS390D pinout SN74LS390D datasheet pdf SN74LS390D equivalent SN74LS390D replacement SN74LS390D cross reference SN74LS390D price SN74LS390D stock Texas Instruments SN74LS390D SN74LS390D 16-SOIC SN74LS390D 30 MHz counter SN74LS390D frequency divider

相关元器件 & 术语

Texas Instruments SN74LS390D SN74LS390DG4 SN74LS390DE4 74LS390SC Motorola SN74LS390D onsemi SN74LS390D 74LS TTL logic family dual 4-bit decade counter logic IC counter and divider sequential logic ripple counter negative-edge clock parallel output ripple-carry output asynchronous clear frequency divider event counter 5 V logic 16-SOIC SOIC package family surface-mount package RoHS REACH
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情