SN74LS390D - Dual 4-Bit Counter, 5V, 16-SOIC | Texas Instruments
MPN: SN74LS390D ✓ نشطSN74LS390D نظرة عامة
A decade counter is a sequential logic device that advances through ten states for each ten input-clock cycles. The SN74LS390 belongs to the 74LS TTL logic family and combines two such counters in one package. Within the broader IC hierarchy, it is a logic IC, counter and divider, and sequential-logic component used to divide frequency, count events, and generate timing signals.
Each counter section supports a maximum counting rate of 30 MHz and includes separate clock inputs, clear inputs, and ripple-carry outputs. The parallel outputs expose the individual stages of each four-stage counter, allowing designers to obtain a divide-by-2, divide-by-4, divide-by-8, or other intermediate division ratio. The 74LS390 architecture is therefore useful when a system needs more than one usable frequency relationship from a common clock source.
The two counting sections operate independently, which allows the SN74LS390D to implement two unrelated counters in one IC or to generate paired timing relationships. Its negative-edge clocking behavior means the active clock transition occurs as the clock input changes from high to low. Clear inputs provide a controlled reset path, while the ripple-carry outputs indicate when a counting section has reached its terminal count and can be used for cascading or event signaling.
Typical uses include digital timing and sequencing circuits, frequency dividers, event counters, clock-generation modules, industrial control logic, and legacy TTL test equipment. The device is particularly useful where parallel stage outputs are required rather than only one final terminal count. Because it belongs to the 74LS family, system-level interface decisions should also account for LS-family rise time, fan-out, noise margin, and propagation-delay requirements.
When laying out a design, place the decoupling capacitor close to the VCC and ground pins and route clock signals away from sensitive analog or high-speed digital nodes. Check the worst-case clock duty cycle and propagation delay before relying on a ripple-carry output to reset or reload another counter. The manufacturer datasheet should be used to assign the complete 16-pin pinout and confirm timing, output-current, and absolute-maximum ratings.
This product page combines manufacturer information, distributor availability references, same-package alternatives, application guidance, and practical design considerations. It distinguishes a true pin-compatible replacement from broader functional alternatives while keeping the key engineering decision—counter architecture, voltage compatibility, and package reuse—central to component selection.
بدائل مباشرة لـ SN74LS390D — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
SN74LS390DG4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS390DE4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
74LS390SC
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
SN74LS390D
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←SN74LS390D
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←SN74LS390D الحدود القصوى والخصائص الكهربائية
| Product Type | Dual 4-bit decade counter |
| Logic Family | 74LS TTL |
| Number of Counter Elements | 2 elements |
| Counter Width | 4 bits per element |
| Counting Sequence | Decade |
| Clock Edge | Negative edge |
| Supply Voltage Range | 4.75 V to 5.25 V |
| أقصى تردد للساعة | 30 MHz |
| نطاق درجة حرارة التشغيل | 0 °C to 70 °C |
| العلبة | 16-pin SOIC, 3.90 mm width |
| نوع التركيب | Surface mount |
| نوع الخرج | Parallel counter outputs |
| Reset Type | Asynchronous clear |
| Number of Counter Stages | 4 stages per counter element |
| Internal Division Sections | Divide-by-two and divide-by-five per element |
| Ripple-Carry Output | Yes, one per counter element |
تكوين أطراف SN74LS390D
| دبوس 1 | 1CLK — Clock input for counter element 1 |
| دبوس 2 | 1CLR — Asynchronous clear input for counter element 1 |
| دبوس 3 | 1Q1 — Parallel output 1 of counter element 1 |
| دبوس 4 | 1Q2 — Parallel output 2 of counter element 1 |
| دبوس 5 | 1Q3 — Parallel output 3 of counter element 1 |
| دبوس 6 | 1Q4 — Parallel output 4 of counter element 1 |
| دبوس 7 | 1RCO — Ripple-carry output for counter element 1 |
| دبوس 8 | GND — Ground reference |
| دبوس 9 | 2Q4 — Parallel output 4 of counter element 2 |
| دبوس 10 | 2Q3 — Parallel output 3 of counter element 2 |
| دبوس 11 | 2Q2 — Parallel output 2 of counter element 2 |
| دبوس 12 | 2Q1 — Parallel output 1 of counter element 2 |
| دبوس 13 | 2RCO — Ripple-carry output for counter element 2 |
| دبوس 14 | 2CLR — Asynchronous clear input for counter element 2 |
| دبوس 15 | 2CLK — Clock input for counter element 2 |
| دبوس 16 | VCC — Positive supply voltage |
التطبيقات النموذجية
SN74LS390D مناسب لـ 6 التطبيقs: Digital Event Counter, Clock Frequency Divider, Industrial Sequence Control, Pulse and Tone Generation, Legacy TTL Test Equipment, Counter-Based Address Sequencing.
Digital Event Counter
The SN74LS390D is appropriate when a system must count recurring events through a decade sequence and expose more than just the terminal count. Each half provides a four-stage negative-edge counter with parallel outputs, allowing divide-by-2, divide-by-4, divide-by-8, and other intermediate count frequencies. One element can count events while the other performs an independent timing function. The 4.75 V to 5.25 V operating range suits conventional 5 V TTL logic, and the 30 MHz maximum clock rate provides margin above typical legacy control frequencies. Designers should use the clear input for deterministic initialization and treat ripple-carry timing as a valid external transition rather than an instantaneous reset.
موصى به
Clock Frequency Divider
The SN74LS390D can divide a master clock without requiring a separate divider for every ratio because each four-stage counter exposes its internal stage outputs. The divide-by-two and divide-by-five organization supports decade counting, while the parallel taps provide useful submultiples of the input frequency. This makes the device suitable for legacy digital timing, pulse-generation, and clock-distribution circuits that need several related rates. At the specified 30 MHz maximum clock frequency, the counter can handle high-rate timing signals, although cascaded ripple paths add stage delay and can introduce phase shift. Select the appropriate output tap and verify duty-cycle distortion and setup time at the driven destination.
موصى به
Industrial Sequence Control
The SN74LS390D can form the timing core of a legacy industrial sequence controller because its two independent counter sections can generate complementary or unrelated count sequences. Parallel stage outputs allow each control stage to detect a specific count condition, while the clear inputs permit synchronized restart after a completed cycle. The 16-pin SOIC package saves board area compared with separate single-counter ICs, and the 0 °C to 70 °C operating range covers many commercial and industrial enclosure conditions. In a control cabinet, add decoupling near the supply pins and route the 30 MHz-capable clock away from sensitive analog circuitry. Firmware and discrete logic should account for ripple-delay differences when coordinating the two halves.
موصى به
Pulse and Tone Generation
The SN74LS390D is useful in simple pulse, tone, and repetitive-timing circuits because each half can divide an incoming clock and expose multiple frequency taps. A divide-by-five section and divide-by-two section can support decimal timing relationships, while the additional stage outputs provide additional choices for pulse-width and repetition-rate generation. Negative-edge clocking makes the device suitable when timing is intentionally triggered on the falling edge of a clock pulse. The maximum 30 MHz clock rating defines the upper operating limit, but output symmetry and usable timing margin depend on the selected output stage and load. Confirm propagation delay and output rise/fall behavior in the manufacturer timing diagram when driving timing-critical downstream logic.
موصى به
Legacy TTL Test Equipment
The SN74LS390D fits legacy TTL test equipment and repair systems that require decade counting, frequency division, or parallel stage observation in a standard 5 V logic environment. Its two independent counters can support measurement sequencing and repetitive stimulus generation in one 16-pin SOIC package. The parallel outputs allow a tester to select a division ratio with external routing rather than rebuilding the counter for each measurement condition. Because the part is part of the established 74LS TTL family, it also fits boards designed around LS logic levels and conventional 5 V supply rails. For long-life equipment, confirm lifecycle status, obsolete-material continuity, and the exact manufacturer’s timing characteristics before committing to a repair quantity.
موصى به
Counter-Based Address Sequencing
The SN74LS390D can provide a repeating decade state for address or step sequencing in small control systems. Because each counter includes four parallel stages, intermediate states can be decoded to create a multi-step sequence without adding a separate binary counter. The second counter element may generate a parallel step sequence, delayed timing sequence, or complementary count. This arrangement reduces logic count in legacy systems while retaining a simple negative-edge clocking model. The 4.75 V to 5.25 V supply range matches standard 5 V TTL interfacing, but the design must account for output rise time, fan-out, and propagation delay when the sequence feeds latches or memory-control logic. Use the clear input to establish a known starting state at power-up.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SN74LS390D — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | SN74LS390DG4 | SN74LS390DE4 | 74LS390SC | SN74LS390D | SN74LS390D |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Rochester Electronics | Motorola | onsemi |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Function | Dual 4-bit decade counter | Dual 4-bit decade counter | Dual 4-bit decade counter | 74LS390 decade counter | Dual 4-bit decade counter | Dual 4-bit decade counter |
أبرز الفروقات
- Two independently clocked decade counters in one package (مقابلSN74LS390D)
- Direct TI ordering alternatives preserve package and supply class (مقابلSN74LS390DG4)
- Parallel counter outputs support flexible frequency division (مقابل74LS390SC)
ملاحظات التصميم
Place the supply decoupling capacitor immediately between the VCC and GND pins, with a short and low-inductance return path. The SN74LS390D supports clock frequencies up to 30 MHz, so long clock traces and shared supply paths can increase susceptibility to edge degradation and coupled noise. Keep clock routing away from analog inputs and use a ground reference that remains continuous beneath the logic section.
Account for the accumulated propagation delay of the internal ripple stages when using a ripple-carry output to trigger another sequential device. Although the maximum clock frequency is 30 MHz, a cascaded design can still experience meaningful phase displacement between terminal and intermediate outputs. Use the parallel stage outputs when a stable selectable division ratio is required, and verify setup and hold time at the receiving logic.
Do not treat similarly named SN74LS390 ordering codes as automatically identical without checking the package and finish designation. In particular, compare the 16-SOIC D suffix against DG4, DE4, or SC variants and confirm the manufacturer’s pin-assignment table. For a board already populated, the replacement must preserve the 16-pin footprint, 5 V supply compatibility, negative-edge clocking, clear behavior, and output functions.
Do not use the SN74LS390D outside its 4.75 V to 5.25 V supply range. The 0 °C to 70 °C rating also restricts use in extended-temperature equipment unless an appropriately qualified part is selected. Check the connected system’s logic levels, fan-out, clock duty cycle, and reset-release timing before finalizing the counter configuration.
معلومات الامتثال
The commercial SN74LS390D is a 0 °C to 70 °C 74LS logic IC. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the available product information. AEC-Q100 qualification is not applicable to this commercial-temperature ordering code.