SN75138D - Quad Bus Transceiver | Texas Instruments
料号: SN75138D ✗ 停产SN75138D 概述
A bus transceiver is an interface IC that connects digital logic to a bidirectional data bus. The SN75138D belongs to the RS-485-style interface hierarchy: its drivers place data onto a single-ended transmission line, while its receivers recover logic-level signals from the same conductors. This arrangement allows one device to support two-way communication while keeping the bus driver inactive when the transceiver is receiving.
The four channels provide independent TTL-compatible driver inputs, receiver outputs, and bus-side driver/receiver connections. A common driver strobe gives the host logic control over whether the open-collector outputs are enabled. High-input-impedance receivers reduce loading on the bus, while the specified 4.75 V to 5.25 V operating range supports conventional 5 V digital systems. The driver outputs support loads up to 100 mA, making the interface suitable for systems requiring wired bus drive rather than only low-power logic interconnection.
Operationally, the SN75138D separates the logic-side signal path from the bus-side signal path. Driver inputs accept TTL levels and control the corresponding open-collector outputs. Receiver inputs monitor the bus and present TTL-compatible signals at the receiver outputs. Clamp diodes help limit excessive voltage excursions on driver outputs, while the high-impedance receiver structure supports shared-bus communication. The common driver strobe provides a single point for coordinating driver state across the four channels.
Typical applications include industrial control buses, instrumentation links, computer peripheral interfaces, multipoint data communication, and embedded systems that require several bidirectional bus connections. The device can also be used where several TTL systems must exchange data over a shared wired network without continuously driving the bus.
For reliable implementation, place the device close to the line-driver and receiver circuitry, route the bus away from sensitive clock and analog signals, and provide the supply bypassing recommended in the manufacturer documentation. Confirm termination, fail-safe biasing, and cable length against the required bus topology. The strobe signal must be sequenced so that only one node drives the shared bus at a time.
This product page summarizes the SN75138D architecture, verified operating characteristics, package details, lifecycle status, replacement considerations, and practical integration guidance. It also distinguishes verified device functions from parameters that require confirmation against the manufacturer datasheet before a new design is released.
直接替换替代料: SN75138D ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
SN65C1167ENSR
✅ 直接替换📋 参考替代料(不在目录中)
SN75138D 规格参数
| Product Type | Quadruple bus transceiver |
| Number of Channels | 4 channels |
| Channel Configuration | 4 driver and 4 receiver channels |
| Duplex Support | Half-duplex |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Driver Output Type | Open-collector |
| Maximum Open-Collector Output Current | 100 mA |
| Receiver Input Impedance | High input impedance |
| Receiver Threshold | High threshold |
| Logic Compatibility | TTL-compatible |
| Driver Control | Common driver strobe |
| Transient Protection | Clamp diodes on driver outputs |
| Operating Speed | High-speed operation |
| 封装 | 16-pin SOIC (D) |
| 安装类型 | Surface mount |
| Packaging Type | Tube |
SN75138D 16-pin soic (d) 引脚配置指南
SN75138D(16-pin soic (d) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: SN75138D.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SN75138D 适用于 6 应用s: Industrial Control Bus Interfaces, Multipoint Data Communication, Embedded Instrumentation Links, Computer Peripheral Interfaces, Data Acquisition Systems, Legacy Test Equipment.
Industrial Control Bus Interfaces
The SN75138D fits legacy industrial control nodes that need four half-duplex bus channels on a 5 V logic rail. Each channel combines a TTL-compatible driver with a high-input-impedance receiver, allowing a controller to exchange commands and status over shared single-ended conductors. Its open-collector outputs support loads up to 100 mA, while the common driver strobe helps the host keep all drivers off except during transmission. The principal trade-off is the obsolete lifecycle, so new deployments should assess current sourcing and validate thermal, timing, and bus-length requirements before production release.
推荐
Multipoint Data Communication
The SN75138D can connect several TTL-based nodes to a shared single-ended bus where only one transmitter should be active at a time. High-input-impedance receiver inputs reduce bus loading, and the open-collector driver outputs support wired logic when paired with correct pull-up and termination networks. The common driver strobe provides centralized control over all four driver outputs, which simplifies arbitration logic in embedded controllers. Designers should calculate the pull-up value from driver sink current, cable length, node count, and rise-time limits, and should verify that the 4.75 V to 5.25 V supply range matches the surrounding system.
推荐
Embedded Instrumentation Links
For embedded measurement and control equipment, the SN75138D provides four independent driver and receiver channels for linking TTL logic to wired field buses. The high-threshold receiver supports noise-tolerant decoding of the bus state, while the high-input-impedance input structure helps preserve integrity on shared lines. Clamp diodes on the open-collector outputs add transient handling around the driver pins. Because this part is obsolete, instrument designers should preserve it for repairs to proven platforms and prefer a currently supported transceiver for new field-instrument designs unless lifecycle risk is formally accepted.
推荐
Computer Peripheral Interfaces
The SN75138D can bridge legacy TTL peripherals and controllers through four half-duplex bus channels. The driver inputs and receiver outputs allow the host logic to use familiar digital levels, while the open-collector bus side supports shared conductors and wired pull-up behavior. A common strobe lets firmware disable the drivers during reception, reducing the risk of output contention. For peripheral modernization, check whether the target cable, termination, and signal rates remain compatible with the original transceiver, because the SN75138D’s obsolete status can outweigh the convenience of reusing an existing board.
推荐
Data Acquisition Systems
The SN75138D is suitable for legacy data-acquisition chassis in which several sensor or controller nodes communicate with a central TTL interface. Four channels reduce the number of separate bus transceivers required, and the receiver’s high input impedance avoids unnecessarily loading the measured network. The 4.75 V to 5.25 V supply range aligns with conventional 5 V acquisition hardware, while the common driver strobe supports orderly command-and-response traffic. Designers should isolate sensitive analog inputs from the bus routing and verify that the line-driver outputs do not introduce unacceptable loading in the selected termination topology.
推荐
Legacy Test Equipment
The SN75138D can support repair and extension of older test systems that use four TTL-controlled, half-duplex bus links between an instrument controller and peripheral fixtures. The open-collector outputs handle loads up to 100 mA, and the high-impedance receivers reduce loading on connected lines. The common driver strobe is useful for fixture designs that require coordinated transmit and receive states. Before incorporating the device into maintained equipment, verify the original bus termination, cable length, logic thresholds, and timing margin, and obtain remaining stock through a formal quotation because production availability is limited.
推荐
推荐产品汇总
工程参考数据: SN75138D ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SN65C1167ENSR |
|---|---|---|
| Package | SOIC-16 (D) | SOIC-16 |
| Brand | Texas Instruments | Texas Instruments |
关键差异点
- Four independently usable transceiver channels in one 16-pin package (对比 SN65C1167ENSR)
- Defined 5 V operating range and 100 mA open-collector capability (对比 SN65C1167ENSR)
- Common driver strobe supports coordinated bus arbitration (对比 SN65C1167ENSR)
设计说明
Do not allow more than one node to enable its bus driver at the same time. The SN75138D uses open-collector outputs, so conflicting enabled drivers can create excessive sink or source current and an undefined bus level. Use the common driver strobe in a controlled sequence, hold drivers disabled while receiving, and define arbitration behavior for startup, reset, and fault recovery.
Calculate pull-up and termination values from the actual bus topology rather than copying a generic resistor value. Consider driver sink-current capability, the 100 mA stated output rating, receiver input impedance, cable length, node capacitance, and the required signal rise time. Place termination only where required by the bus architecture and keep stub branches short to limit reflected signals.
Place the transceiver close to the bus connector and separate bus traces from clocks, sensitive analog inputs, and switching-regulator nodes. Provide local supply decoupling and return the driver and receiver paths as a controlled, continuous interface between the connector and device. Use a ground-plane layout that avoids splitting return paths beneath the device, and follow the manufacturer pin-description table for the final net assignments.
The SN75138D is specified for a 4.75 V to 5.25 V supply range, so verify that supply tolerance, startup sequencing, and local rail noise remain inside the device requirements. Confirm supply current and power dissipation against the actual enabled-driver state and bus load. An estimated thermal calculation must use the final worst-case supply, output voltage, and load conditions before a production design is approved.
合规信息
The available product summary does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for the exact SN75138D ordering suffix. Request current material-compliance documentation with a quotation.