SN75159N - Dual RS-422/485 Driver | Texas Instruments
料号: SN75159N ✓ 量产中SN75159N 概述
A differential line driver is an interface IC that converts logic-level signals into balanced differential outputs suitable for reliable, noise-resistant communication over cables. The SN75159 belongs to the RS-422 driver family within the broader interface-IC and bus-transceiver hierarchy. Its differential outputs help reject common-mode noise, while the 3-state capability prevents an inactive driver from loading a shared bus.
The device provides two differential driver channels, single 5 V operation, TTL-compatible inputs, and independent controls for each channel. When its output-control input is low, the corresponding output pair becomes high-impedance and can neither drive nor load the bus. This behavior supports multiple transmitters sharing a party-line bus when only one driver is intended to be active at a time. The manufacturer identifies the SN75159 as meeting or exceeding ANSI EIA/TIA-422-B and ITU Recommendation V.11 requirements.
The SN75159 is a driver rather than a full transceiver: it does not include receiver channels for returning data from the bus. Its 14-pin PDIP construction is appropriate for through-hole industrial, control, instrumentation, and legacy communication equipment where socketed or manually assembled DIP packaging is preferred. Because each channel can be disabled independently, the device can support multiple physical drivers on one bus when their active intervals are properly coordinated.
Typical uses include industrial automation links, RS-422 point-to-point links, multidrop party-line systems, test equipment, process-control instrumentation, and data acquisition systems requiring balanced differential signaling. The 5 V supply and TTL-compatible control interface simplify connection to older logic systems, while independent channel control supports bus segmentation or spare-driver arrangements.
The primary design consideration is ensuring that only one transmitter actively drives a shared bus at a time. Output-enable timing, grounding, cable termination, and driver-output loading must be evaluated together. The differential outputs should connect to the intended RS-422 network using an appropriate cable and termination scheme; the manufacturer datasheet should be consulted for the complete electrical limits and pin assignments.
This page organizes the SN75159N interface function, verified operating characteristics, practical use cases, and design cautions into an engineering-focused guide. It also separates confirmed product information from parameters that require direct confirmation with the manufacturer before schematic release or production procurement.
直接替换替代料: SN75159N ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料SN75159N 规格参数
| Product Type | Dual differential line driver |
| Driver Configuration | 2 differential driver channels |
| Logic Compatibility | TTL compatible |
| 电源电压 | 5 V |
| Supported Standards | ANSI EIA/TIA-422-B and ITU Recommendation V.11 |
| Interface Classification | RS-422/RS-485 driver |
| Output State Control | Independent control for each driver |
| Disabled Output Impedance | High impedance |
| Line Operation | Balanced differential |
| Bus Arrangement | Party-line operation |
| Package Type | 14-pin PDIP |
| 安装类型 | Through-hole |
| Datasheet Revision | Rev. B |
SN75159N 14-pin pdip 引脚配置指南
SN75159N(14-pin pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: SN75159N.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SN75159N 适用于 6 应用s: Industrial RS-422 Automation Links, RS-485 Transmitter-Only Interface, Party-Line Data Bus, Process-Control Instrumentation, Data Acquisition Equipment, Legacy Test and Measurement Systems.
Industrial RS-422 Automation Links
The SN75159N suits industrial control equipment that sends TTL-compatible commands or sensor data over a balanced differential line. Its two driver channels provide separate transmit paths, while differential signaling improves common-mode-noise tolerance over longer industrial cables. The single 5 V supply simplifies integration with legacy controller logic. The 14-pin PDIP package also supports socketed assembly and field-serviceable through-hole boards. Designers should pair the device with an RS-422 receiver when the remote endpoint must return data, and verify timing and cable termination against the manufacturer specifications.
推荐
RS-485 Transmitter-Only Interface
The SN75159N can implement the transmit side of an RS-485 interface because it provides two differential drivers and independent 3-state output controls. A separate receiver is required when the system must detect incoming bus data. This arrangement is useful for controllers that periodically command field devices while accepting replies through a dedicated receive path. Because multiple transmitters may share the bus, firmware and hardware must ensure that only one channel drives the line during a given interval. Differential routing, grounding, and termination remain important for dependable operation.
推荐
Party-Line Data Bus
The SN75159N is designed for party-line operation in which multiple transmitters can connect to one balanced bus. According to the manufacturer datasheet, driving an output-control input low forces the associated outputs into a high-impedance state so that an inactive driver does not load the line. The two independently controlled channels can address separate nodes or implement prioritized access. Correct arbitration timing is essential because only one transmitter should actively drive the bus at a time. The design should also account for propagation delay, enable settling time, cable length, and the termination required by the network topology.
推荐
Process-Control Instrumentation
The SN75159N can transmit control and measurement information from process-control instrumentation over a balanced differential connection. Its two independent driver channels reduce the need for separate line-driver ICs when a controller has two outbound signal paths. TTL-compatible logic control and a 5 V supply support integration with conventional control electronics. The PDIP format is useful for instrument panels and legacy industrial systems assembled for maintainability. Engineers must define grounding and isolation requirements, select suitable cable termination, and confirm that the electrical output levels match the selected RS-422 receiver and cable length.
推荐
Data Acquisition Equipment
The SN75159N is useful in data-acquisition systems that distribute commands or collect outputs through differential communication channels. Two independent 3-state drivers permit one channel to remain inactive while the other communicates, avoiding unwanted bus loading during test-sequence changes. The device's balanced outputs are intended for robust transmission over longer cables compared with single-ended logic. For acquisition systems that need bidirectional links, pair it with a suitable receiver and define the direction-control logic around the output-enable pins. Validate channel timing, output loading, and ground potential before connecting external equipment.
推荐
Legacy Test and Measurement Systems
The SN75159N fits legacy test and measurement equipment that uses a 5 V supply, TTL-compatible controls, and a through-hole interface IC. It can provide two balanced outputs for driving remote instruments, fixtures, or communication peripherals while allowing each channel to be disconnected electrically from a shared line. The 14-pin PDIP format simplifies socket-based prototyping and maintenance in established instrument platforms. Confirm the device's electrical limits and enable timing in the manufacturer datasheet, maintain consistent signal grounding, and observe the output-state restrictions whenever more than one driver shares a conductor.
推荐
推荐产品汇总
工程参考数据: SN75159N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Product Type | Dual differential line driver |
| Driver Channels | 2 |
| Supply Voltage | 5 V |
| Interface | RS-422/RS-485 transmitter |
| Output Control | Independent control for each driver |
| Disabled Output State | High impedance |
| Package | 14-pin PDIP |
| Brand | Texas Instruments |
| Standards | ANSI EIA/TIA-422-B and ITU Recommendation V.11 |
关键差异点
- Independent output disable for each differential channel (对比 SN75158)
- Two balanced transmit paths in one device (对比 SN75158)
- Shared-bus isolation through 3-state outputs (对比 SN75158)
设计说明
Ensure that no two transmitters actively drive the same differential pair at the same time. According to the manufacturer datasheet, an output-control input in its low state places the associated SN75159N outputs in a high-impedance state, preventing them from driving or loading the bus. Use non-overlapping control timing and include adequate settling time before changing a channel's output state.
Route each differential driver pair as a closely coupled pair and keep it away from unrelated switching nodes and high-current paths. Maintain a continuous ground reference for the interface circuit and follow the connection and termination guidance in the Texas Instruments datasheet. The 14-pin PDIP footprint should be checked against the official pin-configuration diagram before drill or wiring work begins.
Treat output-enable timing as part of the interface budget rather than as an afterthought. Allow for both the channel's propagation delay and the time required for a high-impedance output to stop loading the line before another transmitter is enabled. In party-line systems, test worst-case enable overlap, cable length, receiver loading, and termination because these factors determine whether the bus remains usable during transitions.
合规信息
The manufacturer datasheet confirms ANSI EIA/TIA-422-B and ITU Recommendation V.11 compatibility, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not present in the cited source material.