TAS5613PHD - 150W Stereo Class-D Power Stage | Texas Instruments
料号: TAS5613PHD ✓ 量产中TAS5613PHD 概述
A Class-D audio power stage is an efficient switching amplifier that converts analog audio signals into high-power drive for loudspeakers. It belongs to the amplifier IC hierarchy, specifically the audio amplifier and power-amplifier categories. Compared with linear audio amplifiers, Class-D architectures can provide high output power with lower power dissipation because the switching elements are operated near their fully-on or fully-off states. Integrated feedback helps the device regulate its power stage and supports repeatable amplifier design.
The TAS5613PHD delivers up to 150 W in a stereo configuration and up to 300 W in a mono configuration. According to the manufacturer product page, distortion can be as low as 0.03% THD at 1 W into 4 ohms, while flat total harmonic distortion across frequency is positioned for natural sound reproduction. Power-supply rejection reaches 80 dB in bridge-tie-load operation without an input signal, and signal-to-noise ratio can exceed 100 dB when weighted for A.
The device uses PurePath HD analog-input technology and provides click-and-pop-free startup and shutdown behavior. Its integrated-feedback architecture is intended to simplify power-stage implementation while retaining high-frequency signal capability. The manufacturer identifies pin compatibility with the TAS5630, TAS5615, and TAS5611 families, enabling designers to evaluate different power levels or feature sets while retaining a common package strategy.
Typical applications include high-power stereo audio receivers, active loudspeakers, home-theater amplification, multichannel audio systems, and compact subwoofer or full-range driver stages. The 150 W stereo rating is particularly relevant to consumer and professional audio equipment where a single integrated stage can drive conventional passive loudspeakers efficiently. The 300 W mono configuration offers additional flexibility for bridged applications or higher-power single-channel systems.
Thermal design remains a central implementation consideration because Class-D power stages concentrate losses in the switching devices and package. Follow the manufacturer’s recommended land pattern, component placement, thermal-pad connection, power-supply decoupling, and output-filter guidance. Account for worst-case supply voltage, channel imbalance, amplifier gain, and enclosure temperature rather than sizing the system only from nominal output power.
This page organizes the manufacturer’s key technical facts, package information, family relationships, and engineering guidance for faster component evaluation. The comparison and selection sections also clarify how the pin-compatible TAS5613PHD relates to other PurePath HD power stages when power capability, channel architecture, and thermal requirements differ.
直接替换替代料: TAS5613PHD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TAS5613PHD (相同外形与封装尺寸) ——差异在于 Maximum Stereo Output Power, Product Type, Maximum Mono Output Power, Package, Total Harmonic Distortion.
TAS5615PHD
✅ 直接替换联系询价
查看数据手册 →TAS5611PHD
✅ 直接替换联系询价
查看数据手册 →TAS5630DKD
✅ 直接替换联系询价
查看数据手册 →TAS5613PHD 最大额定值与电气特性
| Product Type | Stereo Class-D analog-input audio power stage |
| Maximum Stereo Output Power | 150 W |
| Maximum Mono Output Power | 300 W |
| Power-Supply Operating Range | 18 V to 38 V |
| Analog Input Range | 10.8 V to 13.2 V |
| Signal Bandwidth | Up to 80 kHz |
| Total Harmonic Distortion | 0.03% at 1 W into 4 ohms |
| Power-Supply Rejection Ratio | 80 dB in BTL configuration without an input signal |
| Signal-to-Noise Ratio | >100 dB, A-weighted |
| Channel Configuration | 1-channel mono or 2-channel stereo |
| Feedback Architecture | Integrated feedback |
| Input Architecture | Analog input |
| Startup and Shutdown Behavior | Click-and-pop-free |
| 封装 | 64-pin HTQFP, 14 mm x 14 mm |
| 安装类型 | Surface mount |
| Pin Compatibility | Compatible with TAS5630, TAS5615, and TAS5611 families |
TAS5613PHD 64-pin htqfp, 14 mm x 14 mm 引脚配置指南
TAS5613PHD(64-pin htqfp, 14 mm x 14 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TAS5613PHD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TAS5613PHD 适用于 6 应用s: Home-Theater Stereo Amplifier, Active Loudspeaker Power Module, Professional Audio Monitor, Subwoofer and Full-Range Driver Amplifier, Multichannel AV Receiver Output Stage, Automotive or Industrial Audio System.
Home-Theater Stereo Amplifier
The TAS5613PHD fits a high-power home-theater output stage because it supports 150 W stereo operation from an 18 V to 38 V power supply and provides signal bandwidth up to 80 kHz for high-definition audio sources. Its integrated-feedback architecture helps simplify the power stage, while click-and-pop-free startup and shutdown reduce unwanted transients during theater-mode changes. In a typical design, the analog drive signal enters the power-stage inputs and filtered Class-D outputs connect to the speaker channels through the manufacturer-recommended network. The 0.03% THD figure at 1 W into 4 ohms is useful for low-level listening, but thermal design must cover sustained high-output conditions.
推荐
Active Loudspeaker Power Module
The TAS5613PHD is suitable for an active loudspeaker module requiring a high-efficiency, high-output analog-input power stage. Its 150 W stereo rating or 300 W bridged-mono capability can serve conventional passive-driver networks when the power supply and thermal system are designed for that load. Integrated feedback supports a compact implementation, while the 80 kHz bandwidth accommodates high-resolution program material. The output-filter and switching-node layout must follow the manufacturer’s reference design, and copper heat spreading is essential because package dissipation increases with output power and channel loading.
推荐
Professional Audio Monitor
The TAS5613PHD can serve as the power stage in a professional monitor or near-field loudspeaker when both output capability and low-level signal fidelity are important. The manufacturer specifies THD as low as 0.03% at 1 W into 4 ohms and flat THD behavior across frequency for natural sound reproduction. Its analog input allows direct integration with a preamplifier or DAC output stage, while integrated feedback reduces the complexity of discrete power-amplifier loops. The amplifier must still be evaluated for thermal rise, output-filter component tolerance, EMI behavior, and protection requirements under sustained monitoring conditions.
推荐
Subwoofer and Full-Range Driver Amplifier
The TAS5613PHD is appropriate for a bridged subwoofer stage because the manufacturer identifies up to 300 W mono operation and supports 1-channel or 2-channel configurations. Its 18 V to 38 V operating range permits use with a conventional high-current audio supply, while the integrated-feedback topology supports predictable power-stage behavior. In a subwoofer implementation, the device drives the speaker through the prescribed external output-filter and inductor network rather than connecting the raw switching output directly to the load. Component selection for the filter, power-supply wiring, and heat sink should reflect the selected load impedance and worst-case audio demand.
推荐
Multichannel AV Receiver Output Stage
The TAS5613PHD can be used in each output channel of a multichannel AV receiver when a common high-power Class-D architecture is preferred. Its selectable mono and stereo operation lets designers establish channel configurations according to the amplifier-board topology, while 150 W per stereo channel supports typical cinema and music loudspeaker loads. The 80 kHz signal bandwidth is suitable for high-definition source material, and click-and-pop-free startup improves user experience during mute and power transitions. Multi-channel deployment multiplies heat dissipation, so designers should evaluate each channel’s loading, fault condition, shared supply impedance, and enclosure cooling rather than sizing the system from one channel alone.
推荐
Automotive or Industrial Audio System
The TAS5613PHD can support industrial or automotive audio systems when its 18 V to 38 V supply range, analog interface, and 150 W stereo capability align with the available power architecture. The integrated-feedback power stage is useful in space-constrained equipment where a high-output Class-D solution is preferable to a large linear amplifier. Designers must verify the exact temperature limits, vibration environment, EMI constraints, and protection requirements against the manufacturer datasheet because the device is not automatically qualified for every automotive program. The exposed thermal pad and high-current output connections also require a robust land pattern, copper plan, and chassis or heat-sink strategy.
推荐
推荐产品汇总
工程参考数据: TAS5613PHD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TAS5615PHD | TAS5611PHD | TAS5630D |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 64-pin HTQFP (14 mm x 14 mm) | 64-pin HTQFP (14 mm x 14 mm) | 64-pin HTQFP (14 mm x 14 mm) | 64-pin HTQFP (14 mm x 14 mm) |
| Product Type | Stereo Class-D analog-input audio power stage | Pin-compatible PurePath HD power stage | Pin-compatible PurePath HD power stage | Pin-compatible PurePath HD power stage |
| Maximum Stereo Output Power | 150 W | 150 W | 150 W | 300 W |
| Maximum Mono Output Power | 300 W | 300 W | 300 W | 600 W |
关键差异点
- Documented compatibility across three related TI power-stage families (对比 TAS5630D)
- 150 W stereo and 300 W bridged-mono capability (对比 TAS5615PHD)
- High-frequency audio bandwidth with low-level distortion (对比 TAS5611PHD)
- Integrated feedback and clean startup behavior (对比 TAS5630D)
设计说明
Use the exposed thermal pad as the primary heat-transfer path and connect it to the thermal and ground structure specified by the manufacturer datasheet. Estimated: power dissipation equals output power divided by amplifier efficiency minus the DC input power; at 150 W output and 90% efficiency with a 24 V supply, approximately 6.9 W enters the amplifier as electrical loss and must be removed through the package. The actual operating temperature depends on copper area, airflow, ambient temperature, and the manufacturer’s thermal model, so verify the design against the maximum channel load.
Place the input, feedback, power-supply, and output-filter components exactly as shown in the manufacturer application circuit. Keep the high-current switching loops compact, use multiple PCB layers to distribute power and ground, and avoid routing sensitive feedback traces beside switching-node nets. The 80 kHz signal bandwidth makes physical layout and component tolerances relevant to channel matching. Confirm the exposed-pad connection, via pattern, output inductors, and input network against the manufacturer land pattern rather than adapting a generic 64-pin HTQFP layout.
Design the 18 V to 38 V supply path for the current required by the selected stereo, mono, or bridged configuration. Estimated: at 150 W output, 90% efficiency, and 24 V supply, the average supply current is about 6.9 A; at 300 W bridged output it is about 13.9 A. These estimates show why local high-current decoupling, low-impedance supply wiring, and transient-response margin are important. Confirm average and peak current with the manufacturer’s application circuit because music transients and channel imbalance can increase demand.
Do not treat pin compatibility as proof of drop-in electrical equivalence. Before replacing TAS5613PHD with TAS5615PHD, TAS5611PHD, or TAS5630D, compare the power rating, supply range, input voltage, feedback network, gain, output-filter values, protection behavior, and exposed-pad connection. A higher-power alternative can dissipate more heat even when its package dimensions match. Also avoid applying a supply outside the 18 V to 38 V operating range or exceeding the absolute maximum ratings listed in the manufacturer datasheet.
Use the recommended external output-filter components and maintain the specified switching-node copper geometry to limit differential-mode and common-mode emissions. Feedback components should be positioned away from inductors and high-current switching areas, and analog input traces should use a quiet reference path. Validate the assembled amplifier with a representative speaker cable and enclosure because radiated emissions and audible artifacts can depend on the output-filter response, grounding, cable length, and chassis geometry rather than only on IC selection.
合规信息
The TI product page identifies TAS5613 as active but does not state the requested environmental or automotive compliance classifications.