THS4211DRB - 1 GHz Low-Distortion Op Amp | Texas Instruments
料号: THS4211DRB ✓ 量产中THS4211DRB 概述
A high-speed voltage-feedback operational amplifier is a transistor-based amplifier that uses negative feedback to amplify signals while maintaining controlled bandwidth, gain, and phase behavior. Within the amplifier hierarchy, the THS4211DRB is an operational amplifier, a voltage-feedback amplifier, and a high-speed signal-conditioning IC. Its unity-gain stability allows operation without a decompensation resistor, while its 3 mm by 3 mm VSON package supports compact analog, video, communications, and test-equipment circuits.
The principal performance features include 1 GHz small-signal bandwidth, 970 V/µs slew rate, 200 mA output drive, and low third-harmonic distortion of -90 dBc at 30 MHz. Differential gain is specified at 0.003°, and the 130 MHz bandwidth with 0.1 dB gain variation supports wideband signal paths. These characteristics are particularly useful when large output transitions, multi-channel timing, or high-order harmonic content would otherwise limit system performance.
The voltage-feedback topology provides a direct relationship between input differential voltage and output voltage, with gain determined mainly by external feedback components. Unity-gain stability makes the device usable as a buffer, while higher closed-loop gains can be created with conventional resistor networks. The exposed thermal pad provides the primary path for heat removal when the amplifier dissipates appreciable power during large-signal operation. Designers should account for output-current demand, supply headroom, feedback-component matching, and parasitic capacitance when working at high frequencies.
Typical applications include high-speed analog buffers, video-signal conditioning, active filters, current-sense amplifiers, communications receivers, and laboratory or instrumentation front ends. The 1 GHz bandwidth and 970 V/µs slew rate also make the device suitable for waveform edges that must remain square or accurately reproduced. A gain or bandwidth tradeoff may be required when the input signal contains significant out-of-band energy.
For layout, use a low-inductance ground plane, place feedback components close to the amplifier pins, and provide very short return paths for both supply rails. The exposed pad should be connected to the ground plane through multiple vias while observing the package land-pattern requirements. Decoupling capacitors should be placed directly at the supply pins, and test points should not interrupt high-speed feedback traces.
This product page combines the manufacturer's principal performance characteristics, commercial sourcing information, and application-focused engineering guidance. It also distinguishes exact drop-in interchangeability from devices that merely use a related package, helping designers evaluate PCB reuse, signal bandwidth, thermal capability, and supply requirements before committing to a replacement.
直接替换替代料: THS4211DRB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料THS4211DRB 最大额定值与电气特性
| Amplifier Type | Single-channel voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain Stability | Unity-gain stable |
| Small-Signal Bandwidth | 1 GHz |
| Slew Rate | 970 V/µs |
| Third-Harmonic Distortion | -90 dBc at 30 MHz |
| Flat-Bandwidth Gain | 130 MHz at 0.1 dB |
| Differential Gain | 0.003° |
| Output Drive Current | 200 mA |
| Supply Voltage Range | 5 V to 15 V |
| 电源电流 | 19 mA |
| Output Current | 220 mA |
| Shutdown Supply Current | 7 µA |
| 工作温度范围 | -40 °C to 85 °C |
| 封装 | 8-VSON with exposed pad, 3 mm × 3 mm |
| 安装类型 | Surface mount |
THS4211DRB 8-vson with exposed pad, 3 mm × 3 mm 引脚配置指南
THS4211DRB(8-vson with exposed pad, 3 mm × 3 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: THS4211DRB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
THS4211DRB 适用于 6 应用s: High-Speed Video Signal Conditioning, Active Wideband Filtering, Communication Receiver Front Ends, Precision Current-Sense Amplification, Test and Measurement Instrumentation, High-Speed Data Acquisition.
High-Speed Video Signal Conditioning
The THS4211DRB fits video amplification and buffering because it combines 1 GHz bandwidth with a 970 V/µs slew rate, allowing fast transition edges to remain well controlled. Its -90 dBc third-harmonic distortion at 30 MHz is valuable when downstream circuitry must receive a clean amplified representation of the source signal. The amplifier can be configured at unity gain or with conventional external feedback while maintaining stability. The 200 mA output-drive specification provides margin for suitable video loads, but cable and termination capacitance should be included in simulation because they can reduce stability or trigger ringing.
推荐
Active Wideband Filtering
The THS4211DRB is suitable for active filters requiring accurate amplification over a broad frequency range. Its 1 GHz small-signal bandwidth, 130 MHz bandwidth at 0.1 dB, and 0.003° differential gain provide useful performance targets for multi-stage filter design. The 970 V/µs slew rate helps preserve large-signal behavior, while unity-gain stability simplifies buffer stages. Component tolerance, parasitic capacitance, and amplifier noise can alter the realized response, so simulate the complete filter around the intended gain and load rather than relying only on nominal bandwidth figures.
推荐
Communication Receiver Front Ends
The THS4211DRB can serve in high-speed receiver front ends where signal amplification must preserve both amplitude and phase. Its 1 GHz bandwidth handles wideband data paths, while the 970 V/µs slew rate supports rapid transitions and the 200 mA output-drive capability supports suitable termination networks. Low distortion at 30 MHz can reduce added spectral content in measurement or demodulation paths. The designer must still verify common-mode limits, input-referred noise, gain flatness, and the effect of PCB parasitics across the operating frequency range.
推荐
Precision Current-Sense Amplification
The THS4211DRB can amplify small differential signals in current-measurement systems when high bandwidth is important. Its 0.003° differential-gain figure and 1 GHz bandwidth support accurate treatment of rapidly changing current signals, while the 970 V/µs slew rate limits slew-related error during fast edges. A low-value sense resistor can produce millivolt-scale signals that require careful grounding and Kelvin routing. Check input and output common-mode ranges, supply headroom, and the amplifier's offset and noise characteristics against the measurement resolution required by the application.
推荐
Test and Measurement Instrumentation
The THS4211DRB is appropriate for instrumentation requiring low-distortion buffering of fast test signals. Its 1 GHz bandwidth, 970 V/µs slew rate, and 200 mA output drive allow it to retain signal shape across many waveform-generator and analyzer input ranges. Unity-gain stability supports direct buffer use, while external feedback permits selectable gain. At the 3 mm by 3 mm VSON scale, thermal design and ground-plane continuity become especially important; route the exposed pad to a solid ground area and keep input and output loops physically separate to reduce parasitic feedback.
推荐
High-Speed Data Acquisition
The THS4211DRB fits the analog input stage of high-speed data-acquisition systems that need wide bandwidth and low distortion. The 1 GHz amplifier bandwidth and 970 V/µs slew rate can preserve short input pulses before conversion, while the -90 dBc distortion specification at 30 MHz limits added harmonics. Input protection, anti-alias filtering, source impedance, and ADC acquisition timing must be evaluated together. A compact layout with very short traces and local decoupling reduces parasitic effects that could otherwise consume the amplifier’s high-frequency performance margin.
推荐
推荐产品汇总
工程参考数据: THS4211DRB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 8-VSON with exposed pad, 3 mm × 3 mm |
| Brand | Texas Instruments |
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Small-Signal Bandwidth | 1 GHz |
| Slew Rate | 970 V/µs |
| Supply Voltage Range | 5 V to 15 V |
| Output Drive Current | 200 mA |
| Third-Harmonic Distortion | -90 dBc at 30 MHz |
| Gain Stability | Unity-gain stable |
关键差异点
- Combines very high bandwidth with strong large-signal capability (对比 General-purpose low-speed operational amplifiers)
- Maintains stable operation at unity gain (对比 Decompensated high-speed amplifiers)
- Provides low distortion for high-frequency signal paths (对比 General-purpose amplifiers used for video conditioning)
设计说明
Place input, output, and feedback components directly adjacent to the THS4211DRB pins. Keep the feedback loop physically small and route the non-inverting and inverting traces away from supply and output-current paths. At 1 GHz bandwidth, even a short return loop can introduce phase error or instability. Use a continuous ground plane beneath the device, connect the exposed pad with several short thermal vias, and avoid placing test pads or routing discontinuities within the high-speed signal path.
Use the exposed pad as the principal thermal path for the 8-VSON package. The 200 mA output-drive capability can increase dissipation during large-signal operation, while the compact 3 mm by 3 mm body limits passive heat spreading. Estimated thermal design should be based on the actual supply voltage, output swing, load, duty cycle, and ambient temperature. Validate the result with temperature-rise measurement because copper area, via count, adjacent components, and board construction can materially change junction temperature.
Do not assume that any related THS4211 order code is a drop-in replacement. Verify the 8-VSON dimensions, pin numbering, exposed-pad connection, shutdown function, supply limits, and common-mode range in the Texas Instruments manufacturer datasheet. In particular, the THS4215 adds power-down capability, while SOIC and other package options are not mechanically interchangeable. Also check whether the circuit operates at unity gain, where the specified stability is directly useful, or at a closed-loop gain requiring separate stability and bandwidth review.
Terminate and simulate the complete output path because capacitive loading can change the apparent bandwidth, slew behavior, and stability of a 1 GHz amplifier. Keep cable or connector structures away from the device, use controlled impedance routing, and add source or isolation resistors when a downstream load otherwise presents excessive capacitance. Use an oscilloscope bandwidth and probe method that do not obscure the edge being measured; otherwise, probe and instrument loading can be mistaken for THS4211DRB distortion.
合规信息
Compliance attributes are not explicitly identified in the product-page excerpts or distributor listings. Verify current declarations using the Texas Instruments product page and manufacturer documentation.