TJA1028TK/3V3/10:1 - 3.3V LIN Transceiver | NXP
料号: TJA1028TK/3V3/10:1 ✓ 量产中TJA1028TK/3V3/10:1 概述
A LIN transceiver, or Local Interconnect Network transceiver, connects a low-speed serial network node to a vehicle electrical network. The LIN bus belongs to the broader vehicle networking hierarchy, where simple sensors and actuators share a communication backbone with higher-bandwidth vehicle networks. The TJA1028 combines physical-layer signaling with local regulated power, positioning it between standalone LIN transceivers and larger system-basis-chip solutions.
Key features include LIN 2.0 and LIN 2.1 operation, compliance with SAE J2602 and ISO 17987-4:2016 for 12 V systems, a 3.3 V regulated output, and an integrated regulator rated up to 70 mA. The 10:1 ordering suffix identifies the device threshold configuration. Its 8-HVSON package is designed for compact surface-mount assemblies where board area, EMC behavior, and short return paths are important.
The integrated regulator allows a transceiver node to derive a local 3.3 V rail from the vehicle supply while preserving a single LIN bus connection. The regulator and transceiver share a compact package, but their functions remain distinct: the transceiver handles bus-level transmit and receive signaling, while the regulator supports local loads. This separation makes the device suitable for small sensor, actuator, and body-control nodes that do not require a complete system-basis chip.
Typical applications include LIN-controlled vehicle lamps, door modules, seat controls, climate-control peripherals, and compact motor or sensor interfaces. The 3.3 V output is particularly useful for a microcontroller, signal-conditioning circuit, or digital sensor that requires a stable low-voltage rail beside a LIN physical interface. Using one IC for communication and local power reduces PCB area and assembly cost.
PCB implementation should preserve a direct, short LIN connection and follow the manufacturer layout guidance for the HVSON exposed pad and supply decoupling. Confirm the regulator's thermal performance at the expected ambient temperature and ensure that its 70 mA capability is not shared with loads outside the intended design. The manufacturer datasheet pin-description table should be used for exact pad and exposed-pad assignments.
This product page combines the exact ordering information, LIN compliance details, regulator capability, package characteristics, application guidance, and drop-in-family analysis needed to evaluate the TJA1028TK/3V3/10:1 before schematic and PCB sign-off.
直接替换替代料: TJA1028TK/3V3/10:1 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TJA1028TK/3V3/10:1 (相同外形与封装尺寸) ——差异在于 Package.
TJA1028TK/3V3/10/2Z
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1028TK/3V3/10/J
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1028TK/3V3/20/J
✅ 直接替换联系询价
查看数据手册 →TJA1028TK/5V/10:1
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1028TK/5V/10/J
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1028TK/3V3/10:1 规格参数
| Product Type | LIN transceiver with integrated voltage regulator |
| LIN Protocol Support | LIN 2.0 and LIN 2.1 |
| Automotive Network Compliance | SAE J2602 and ISO 17987-4:2016 for 12 V systems |
| System Supply Rating | 12 V |
| Integrated Regulator Output | 3.3 V |
| Integrated Regulator Current | 70 mA |
| Bus-Slope Threshold Ratio | 10:1 |
| Transceiver Type | Half LIN bus transceiver |
| 封装 | 8-HVSON, 3 x 3 mm |
| 安装类型 | Surface mount |
| 工作温度 | -40 °C to +150 °C |
| Packing Method | Tape reel |
| Regulator Topology | Low-drop voltage regulator |
TJA1028TK/3V3/10:1 8-hvson, 3 x 3 mm 引脚配置指南
TJA1028TK/3V3/10:1(8-hvson, 3 x 3 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TJA1028TK/3V3/10:1.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TJA1028TK/3V3/10:1 适用于 6 应用s: Automotive LIN Sensor Nodes, Vehicle Door and Body Modules, Automotive LED Lighting Controls, Climate-Control Peripheral Interfaces, Seat and Motor Control Interfaces, Industrial 12 V LIN Network Equipment.
Automotive LIN Sensor Nodes
The TJA1028TK/3V3/10:1 fits compact sensor nodes that communicate over a 12 V LIN network while requiring a local 3.3 V supply. Its LIN 2.0 and LIN 2.1 support, SAE J2602 and ISO 17987-4:2016 compliance, and 10:1 threshold configuration allow the transceiver to coexist with established vehicle-network behavior. The integrated 70 mA regulator can power a low-power microcontroller, sensor interface, or logic section without a separate regulator IC. A compact 8-HVSON 3 x 3 mm package also helps reduce board area. The design must keep the LIN route short, observe the recommended protection and grounding layout, and keep all regulator loads below 70 mA across the full -40 °C to +150 °C range.
推荐
Vehicle Door and Body Modules
Door and body-control modules can use the TJA1028TK/3V3/10:1 to combine LIN communication with local regulated power in a space-constrained assembly. The transceiver handles the physical LIN connection, while the integrated 3.3 V regulator supplies up to 70 mA for control logic or communication peripherals. The 10:1 threshold configuration is suited to LIN networks specified at 12 V, and the operating range of -40 °C to +150 °C supports harsh vehicle environments. Engineers should allocate the regulator's 70 mA across all local loads, retain an unobstructed thermal path under the exposed pad, and follow the manufacturer layout pattern to minimize susceptibility to bus transients and EMC coupling.
推荐
Automotive LED Lighting Controls
The TJA1028TK/3V3/10:1 is suitable for LIN-addressed lighting controls where a remote lamp or indicator driver needs a compact communication interface and a low-voltage logic rail. The 3.3 V regulator can support up to 70 mA for command logic, status feedback, or a small local controller, while the LIN transceiver provides network connectivity in the same 8-HVSON package. Combining these functions reduces board space compared with a discrete transceiver-regulator arrangement. The 10:1 threshold configuration must align with the vehicle LIN network, and regulator capacity must be checked before adding higher-current LED circuitry. High-current lamp drive and any inductive switching stage should remain separate from this low-voltage supply path.
推荐
Climate-Control Peripheral Interfaces
Compact climate-control peripherals benefit from the TJA1028TK/3V3/10:1 because the LIN transceiver and 3.3 V regulator share one small 8-HVSON package. The integrated regulator can provide up to 70 mA for sensor conditioning, status logic, or a low-power control MCU while the transceiver communicates with the vehicle LIN network. LIN 2.0 and LIN 2.1 support and 12 V SAE J2602 and ISO 17987-4:2016 compliance make the interface suitable for modern vehicle electrical architectures. Designers should account for transient energy on the LIN wiring, maintain a low-impedance ground return, and separate the regulator output from high-current motor-drive stages to prevent load changes from disturbing communication.
推荐
Seat and Motor Control Interfaces
The TJA1028TK/3V3/10:1 can serve as the communication and local-power front end for small seat, latch, or motor-control nodes. Its LIN physical layer provides network access, while the integrated 3.3 V, 70 mA regulator supplies control logic that does not belong directly on the noisy 12 V bus. The compact 8-HVSON footprint supports space-constrained modules, and the -40 °C to +150 °C operating range covers demanding vehicle locations. The motor power stage should use separate robust drive circuitry, with its return currents kept away from the transceiver ground reference. Before release, validate startup, bus thresholds, regulator loading, thermal operation, and fault behavior under the vehicle's worst-case supply and temperature conditions.
推荐
Industrial 12 V LIN Network Equipment
Although primarily an automotive LIN interface, the TJA1028TK/3V3/10:1 can also serve compact industrial equipment connected to a 12 V LIN-compatible network. Its integrated 3.3 V regulator supplies up to 70 mA for local control electronics, reducing the need for a separate regulator when board area is constrained. The 10:1 threshold configuration and LIN 2.0 and LIN 2.1 support must match the network implementation, while the -40 °C to +150 °C range provides broad temperature capability. Industrial deployments still require careful review of ground offsets, wiring protection, EMC conditions, and bus termination or topology requirements. The manufacturer application information should guide the protection network and decoupling arrangement.
推荐
推荐产品汇总
工程参考数据: TJA1028TK/3V3/10:1 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TJA1028TK/3V3/10/2Z | TJA1028TK/3V3/10/J | TJA1028TK/3V3/20/J | TJA1028TK/5V/10:1 | TJA1028TK/5V/10/J |
|---|---|---|---|---|---|---|
| Package | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Integrated Regulator Output | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 5.0 V | 5.0 V |
| Integrated Regulator Current | 70 mA | 70 mA | 70 mA | 70 mA | 70 mA | 70 mA |
| Bus-Slope Threshold Ratio | 10:1 | 10:1 | 10:1 | 20:1 | 10:1 | 10:1 |
| Protocol Support | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 | LIN 2.0 and LIN 2.1 |
| 12 V Bus Compliance | SAE J2602 and ISO 17987-4:2016 | SAE J2602 and ISO 17987-4:2016 | SAE J2602 and ISO 17987-4:2016 | SAE J2602 and ISO 17987-4:2016 | SAE J2602 and ISO 17987-4:2016 | SAE J2602 and ISO 17987-4:2016 |
| Operating Temperature | -40 °C to +150 °C | -40 °C to +150 °C | -40 °C to +150 °C | -40 °C to +150 °C | -40 °C to +150 °C | -40 °C to +150 °C |
关键差异点
- Combines LIN communication and local regulated power (对比 Standalone LIN transceiver without an integrated regulator)
- Uses the 10:1 LIN threshold configuration (对比 TJA1028TK/3V3/20/J)
- Supports the full automotive temperature range (对比 TJA1028TK/5V/10:1)
- Compact integration in an 8-HVSON footprint (对比 Discrete LIN transceiver and regulator implementation)
设计说明
Follow the NXP PCB layout pattern for the 8-HVSON device. Place the regulator input and output capacitors close to their associated pins, provide a short ground return, and connect the exposed thermal pad as specified. Keep the LIN trace and protection components away from sensitive signal paths. A compact bus connection reduces parasitic inductance and improves EMC behavior, particularly when the module is connected through long vehicle wiring.
Build the 3.3 V regulator budget from the 70 mA maximum specified for the TJA1028TK/3V3/10:1. Include microcontroller, sensor, status-indicator, and peripheral currents in the maximum-load case rather than average consumption. Use the 3.3 V output only for loads specified for that voltage, and separate any motor, lamp, or actuator drive stage from the low-voltage rail to prevent transients from disturbing the transceiver.
Use the manufacturer reference layout as the geometric baseline for pad placement, exposed-pad vias, and decoupling. Avoid routing LIN or switching-node copper beneath the exposed pad unless the datasheet explicitly permits it. Keep the ground path short and maintain a low-impedance return around the transceiver. Validate the assembled board for bus ringing, susceptibility, radiated emissions, and regulator stability across the expected supply and load range.
Do not select the 20:1 threshold family option as a silent substitute for the 10:1 device without confirming the network waveform and receiver detection requirements. Likewise, a 5 V output variant is not electrically interchangeable with this 3.3 V part when connected loads require the nominal 3.3 V rail. Confirm the complete ordering suffix, pin assignment, exposed-pad connection, and regulator load before releasing a replacement to production.
合规信息
The manufacturer identifies compliance with SAE J2602 and ISO 17987-4:2016 for 12 V LIN networks. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status should be confirmed for the selected orderable variant in the manufacturer compliance documentation.