TJA1028TK/5V0/10/Z - 5V LIN Transceiver | NXP
料号: TJA1028TK/5V0/10/Z ✓ 量产中TJA1028TK/5V0/10/Z 概述
A LIN transceiver is an interface integrated circuit that connects a host microcontroller to a low-cost, single-wire automotive network. The LIN bus sits below the hierarchical level of a CAN network: LIN is a Local Interconnect Network commonly used for body electronics, comfort controls, lighting, seat functions, and other low-bandwidth vehicle nodes. The TJA1028 combines this network interface with a local regulator, allowing a compact node to obtain both LIN communication and a 5 V supply from one component.
Key features include bus wake-up, low-power mode, TXD timeout protection, thermal shutdown protection, and under-voltage detection. The integrated regulator provides up to 70 mA for local circuitry, while the 4.5 V to 28 V external supply range supports typical 12 V vehicle electrical systems. Its LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 compatibility makes it suitable for standardized in-vehicle networks.
Technically, the TJA1028 combines a LIN physical-layer transceiver with a regulated auxiliary output. The LIN side provides the physical signaling interface between logic-level TXD and RXD signals and the bus. The regulator side reduces the vehicle supply to a fixed 5.0 V. The manufacturer describes strong electrostatic robustness as a key design feature, which is important because vehicle wiring can be electrically noisy and subject to ESD events.
Typical applications include LIN door modules, seat-control units, switch banks, climate-control peripherals, ambient-lighting controllers, and compact body-control nodes. The 5 V variant is especially useful when a local sensor or actuator requires a regulated 5 V rail while the node communicates with a LIN master through the same wiring harness.
Design the 3 mm by 3 mm footprint on a multilayer board with short LIN routing, a stable ground connection, and protection appropriate to the vehicle harness. Follow the manufacturer datasheet for decoupling capacitors, LIN bus protection, pin assignments, and PCB footprint dimensions. The 70 mA regulator is intended for local logic loads rather than high-current actuators.
This page consolidates the device specifications, compliant LIN standards, package details, functional family alternatives, and practical design guidance into an engineering-focused reference for evaluating and implementing compact LIN nodes.
直接替换替代料: TJA1028TK/5V0/10/Z ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
TJA1028TK/3V3/10/Z
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1028TK/5V0/10,1
✅ 直接替换📋 参考替代料(不在目录中)
TJA1028TK/3V3/10,1
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1028TK/5V0/10/Z 规格参数
| Product Type | LIN half-duplex transceiver with integrated voltage regulator |
| LIN Compliance | LIN 2.0, LIN 2.1, SAE J2602 |
| ISO Standard | ISO 17987-4:2016 (12 V) |
| Supply Voltage Range | 4.5 V to 28 V |
| Regulated Output Voltage | 5.0 V |
| Integrated Regulator Output Current | 70 mA |
| LIN Data Rate | 10.4 kbaud |
| Communication Mode | Half-duplex |
| 封装 | 8-HVSON (3 mm x 3 mm) |
| 安装类型 | Surface mount |
| Bus Wake-Up | Supported |
| Low-Power Mode | Supported |
| TXD Timeout Protection | Supported |
| Thermal Shutdown Protection | Supported |
| Under-Voltage Detection | Supported |
TJA1028TK/5V0/10/Z 8-hvson (3 mm x 3 mm) 引脚配置指南
TJA1028TK/5V0/10/Z(8-hvson (3 mm x 3 mm) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TJA1028TK/5V0/10/Z.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TJA1028TK/5V0/10/Z 适用于 6 应用s: Automotive Door Control Module, Seat Control Peripheral, Automotive Switch Bank, Climate Control Peripheral, Automotive Lighting Controller, Compact Body Control Node.
Automotive Door Control Module
The TJA1028TK/5V0/10/Z fits a LIN-connected door node that must communicate with a vehicle master while powering local switches or sensors. Its 10.4 kbaud LIN interface supports the low-bandwidth body-electronics traffic used for switch positions, status reporting, and actuator commands. The integrated 5.0 V regulator can supply up to 70 mA to local logic, reducing the component count compared with a separate transceiver and low-dropout regulator. A 4.5 V to 28 V operating range accommodates a 12 V vehicle environment. Use the manufacturer pin and application guidance to place the exposed pad, connect the LIN network, and route the regulated 5 V rail away from sensitive switch inputs.
推荐
Seat Control Peripheral
A seat-control peripheral is a practical LIN application because it exchanges relatively slow commands and switch-position data rather than streaming high-bandwidth payloads. The TJA1028TK/5V0/10/Z provides the physical LIN interface at 10.4 kbaud and a fixed 5.0 V regulator output rated to 70 mA. That output can support local input logic or a small sensor interface, although motor and heating elements require separate drivers. The device also includes bus wake-up, TXD timeout protection, thermal shutdown, and under-voltage detection, helping the module recover predictably from faults. Keep the LIN route short, provide the bus components shown in the manufacturer application circuit, and verify the 5 V load against the regulator thermal limits.
推荐
Automotive Switch Bank
The TJA1028TK/5V0/10/Z can serve as the communication and local-power device for a compact bank of window, lighting, or climate switches connected to a LIN bus. Its 10.4 kbaud rate is appropriate for reporting individual switch states and receiving commands. The integrated 5.0 V regulator removes the need for a dedicated 5 V LDO when the load is no more than 70 mA, while under-voltage detection and TXD timeout protection improve system recovery behavior. Because switch inputs may experience harness noise and ESD, follow the manufacturer recommendations for bus protection, grounding, and component placement. The local rail should serve logic and sensing circuits only, not direct lamp or motor loads.
推荐
Climate Control Peripheral
A LIN climate-control peripheral can use the TJA1028TK/5V0/10/Z to connect a fan command, temperature sensor, or actuator-control MCU to the vehicle network. The transceiver supports LIN 2.0/2.1 and SAE J2602 operation at 10.4 kbaud, which matches command and diagnostic traffic in a compact body node. The fixed 5.0 V regulator output, rated to 70 mA, can power a sensor interface or low-current logic without a separate regulator. Low-power mode is useful for reducing consumption when the node is inactive, while bus wake-up allows the peripheral to resume when network activity occurs. Do not power fan motors, heaters, or solenoid valves from the regulator; use dedicated driver stages.
推荐
Automotive Lighting Controller
The TJA1028TK/5V0/10/Z is suitable for a LIN-connected ambient-lighting or exterior-lighting controller that receives low-bandwidth commands from a central body controller. Its integrated 5.0 V output can supply up to 70 mA of control logic, while the LIN physical interface handles command reception and diagnostic responses at 10.4 kbaud. The half-duplex architecture supports a compact node implementation, and bus wake-up can reduce the energy required when the vehicle network wakes the module. High-current LEDs must use separate driver circuitry with appropriate transient protection. Keep the LIN trace physically robust, use the manufacturer's recommended bus network, and observe the exposed-pad land pattern to avoid thermal or assembly problems.
推荐
Compact Body Control Node
The TJA1028TK/5V0/10/Z supports compact body-control nodes that combine LIN connectivity with a small regulated supply requirement. Its 4.5 V to 28 V input range, 5.0 V output, and 70 mA regulator capability allow it to operate from a 12 V vehicle battery while powering a local microcontroller or sensor interface. Integrated low-power mode, bus wake-up, under-voltage detection, TXD timeout protection, and thermal shutdown provide useful supervision for a distributed network. Board-space savings come from combining two functions in an 8-HVSON package, but thermal design and exposed-pad soldering remain essential. Use the NXP datasheet for the exact footprint, capacitors, LIN components, and recommended application layout.
推荐
推荐产品汇总
工程参考数据: TJA1028TK/5V0/10/Z ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TJA1028TK/3V3/10/Z | TJA1028TK/5V0/10,1 | TJA1028TK/3V3/10,1 |
|---|---|---|---|---|
| Package | 8-HVSON (3 mm x 3 mm) | 8-HVSON (3 mm x 3 mm) | 8-HVSON (3 mm x 3 mm) | 8-HVSON (3 mm x 3 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Regulator Output Voltage | 5.0 V | 3.3 V | 5.0 V | 3.3 V |
| Integrated Regulator Output Current | 70 mA | 70 mA | 70 mA | 70 mA |
| LIN Data Rate | 10.4 kbaud | 10.4 kbaud | 10.4 kbaud | 10.4 kbaud |
| Operating Supply Range | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V | 4.5 V to 28 V |
| LIN Compliance | LIN 2.0/2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0/2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0/2.1, SAE J2602, ISO 17987-4:2016 | LIN 2.0/2.1, SAE J2602, ISO 17987-4:2016 |
| Integrated Regulator | Yes, low-drop voltage regulator | Yes, low-drop voltage regulator | Yes, low-drop voltage regulator | Yes, low-drop voltage regulator |
| Protection Features | Bus wake-up, TXD timeout, thermal shutdown, under-voltage detection | Bus wake-up, TXD timeout, thermal shutdown, under-voltage detection | Bus wake-up, TXD timeout, thermal shutdown, under-voltage detection | Bus wake-up, TXD timeout, thermal shutdown, under-voltage detection |
| Ordering Suffix | TJA1028TK/5V0/10/Z | TJA1028TK/3V3/10/Z | TJA1028TK/5V0/10,1 | TJA1028TK/3V3/10,1 |
关键差异点
- LIN physical layer and local regulator integrated in one package (对比 TJA1028TK/3V3/10/Z)
- Exact electrical configuration retained by the /10,1 ordering variant (对比 TJA1028TK/5V0/10,1)
- Single-package regulation reduces board partitioning (对比 TJA1028TK/3V3/10,1)
设计说明
Use the NXP manufacturer footprint and land-pattern dimensions for the 8-HVSON package, including its exposed thermal pad. Place the LIN bus components and required decoupling capacitors close to their associated pins, keep the LIN route short, and provide a low-impedance ground connection. Confirm whether the exposed pad is electrically tied to ground in the application circuit and follow the manufacturer's soldering and assembly guidance.
The integrated regulator is rated to deliver up to 70 mA at 5.0 V, but it is intended for local logic and sensing loads. Do not power motors, lamps, solenoids, or other high-current loads from this output. Maintain input and output capacitance required by the manufacturer datasheet, and verify the regulator's thermal behavior with the worst-case vehicle input voltage and expected local-load duty cycle.
Do not confuse the 5.0 V and 3.3 V TJA1028 variants or the /10/Z and /10,1 ordering suffixes. The regulator voltage must match the node's logic requirements, and the exact suffix must match the required ordering and packing configuration. Also avoid using the LIN interface for loads outside its 10.4 kbaud body-network application or omitting the bus protection and wake-up components shown in the manufacturer application circuit.
Place the LIN interface and regulator-return path so switching from other electronics on the board does not couple into the LIN signal or 5 V rail. Keep sensitive sensor nodes and high-current driver stages physically separated where practical. Use the manufacturer's specified bus and filter components, avoid long parallel LIN routing, and connect the package thermal pad according to the recommended layout so heat from the regulator does not create local temperature gradients near the transceiver.
合规信息
The NXP datasheet identifies LIN 2.0/2.1, SAE J2602, and ISO 17987-4:2016 (12 V) compliance. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status were not stated in the available product information and remain unknown.