TJA1048TK Dual High-Speed CAN Transceiver | NXP
料号: TJA1048TK ✓ 量产中TJA1048TK 概述
A CAN transceiver is the physical-layer interface between a digital CAN controller and the wired communication bus. It converts controller logic into differential bus signals and converts received bus levels into logic signals for the controller. Within the hierarchy of automotive communication electronics, the TJA1048TK belongs to the CAN transceiver class, connecting CAN protocol controllers to the vehicle network while supporting high-speed data transfer.
The TJA1048TK combines two independent CAN transceiver channels in one compact package. Its dual-channel architecture reduces the component count and board area required for systems using more than one CAN bus. Standby mode provides an operating state for controlling power consumption or temporarily disabling communication. The small-outline HVSON package is intended for space-constrained assemblies where a conventional leaded or larger-outline package would be less suitable.
The 14-terminal package supports a nominal 5 V operating supply, and its 0.65 mm pitch permits compact routing under automotive-style density constraints. The NXP product page specifies reel-reel packing on 13-inch reels, a minimum package quantity of 6000, a minimum order quantity of 6000, and a stated lead time of 10 weeks. These manufacturing and ordering details make the TJA1048TK appropriate for automated production planning as well as technical evaluation.
Typical uses include automotive body and comfort electronics, engine-control systems, industrial automation equipment, motor-control systems, and other embedded products with one or two CAN communication links. In a two-channel design, one transceiver can serve a body-control module, gateway, diagnostic interface, or automation controller where separate CAN controllers require a common physical-layer device.
PCB implementation should prioritize short CAN traces, a continuous ground reference beneath the transceiver, and compliant decoupling from the nearby supply pins. Because high-speed differential signaling depends on impedance control and symmetry, component placement, trace geometry, connector transitions, and the protection network must be designed together. Use the manufacturer datasheet pin-description table and application guidance when assigning every terminal and selecting bypass capacitance.
This product page combines the manufacturer interface description, ordering information, package dimensions, termination, and practical PCB guidance. It also distinguishes documented functions from unknown electrical details, helping engineers assess TJA1048TK suitability without changing the component or inventing specifications that the manufacturer has not published for this ordering code.
直接替换替代料: TJA1048TK ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料TJA1048TK 规格参数
| Product Type | Dual high-speed CAN transceiver with Standby mode |
| CAN Channel Count | 2 channels |
| Nominal Supply Voltage | 5 V |
| Bus Interface | Differential CAN transmit and receive on a two-wire bus |
| 封装 | 14-HVSON (3 x 4.5 mm) |
| Terminal Count | 14 terminals |
| Terminal Pitch | 0.65 mm |
| 安装类型 | Surface mount |
| Packing | Reel-reel, 13-inch reel |
| Minimum Package Quantity | 6000 pieces |
| Minimum Order Quantity | 6000 pieces |
| Stated Lead Time | 10 weeks |
| Operating Mode | Standby mode |
| Target Application | High-speed automotive CAN communication |
TJA1048TK 6000 pieces 引脚配置指南
TJA1048TK(6000 pieces 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TJA1048TK.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TJA1048TK 适用于 6 应用s: Automotive Body Control Module, Vehicle Network Gateway, Industrial Automation Controller, Motor Control and Diagnostics, CAN Communication Test Module, Embedded Diagnostic Interface.
Automotive Body Control Module
The TJA1048TK fits a body-control module that must connect a microcontroller or application processor to two vehicle CAN networks. Its two high-speed CAN channels consolidate multiple bus interfaces into one 14-HVSON device, while the compact 3 x 4.5 mm package preserves board area. With a nominal 5 V supply and 0.65 mm terminal pitch, the part supports dense automotive electronics layouts. The final design should follow the manufacturer application guidance for CAN line protection, termination, decoupling, and layout symmetry.
Vehicle Network Gateway
A vehicle network gateway can use the TJA1048TK for two differential CAN links that connect separate bus domains to gateway logic. Its dual-channel arrangement reduces the number of physical-layer transceivers required beside the gateway controller. The small 14-HVSON outline is especially useful when gateway boards must accommodate additional communication, memory, and processing functions. Bus-side protection, common-mode handling, and standby control should be designed according to the NXP datasheet and the vehicle's EMC requirements.
Industrial Automation Controller
The TJA1048TK is suitable for industrial automation equipment that participates in two CAN networks for sensor, actuator, or machine-control communication. It provides the differential transmit and receive interface expected by a CAN protocol controller and operates from a nominal 5 V rail. The dual-channel 14-HVSON package reduces board space, while Standby mode supports controlled operating states. Industrial implementations should add appropriate bus protection and verify EMC performance for the installation environment.
Motor Control and Diagnostics
In a motor-control or service-diagnostic unit, the TJA1048TK can support two high-speed CAN connections from one controller. One channel may handle runtime control traffic while another supports diagnostics or a secondary machine network. The device's differential CAN interface matches a controller-based architecture, and its 3 x 4.5 mm package leaves room for power conversion and signal-conditioning components. Keep the CAN routing away from high-switching-current paths and validate the completed board against industrial EMC requirements.
CAN Communication Test Module
A compact communications test module can use the TJA1048TK to provide two high-speed CAN physical interfaces for monitoring, routing, or protocol testing. The dual-channel arrangement allows one controller to handle two independent bus connections without requiring two separate transceiver packages. The small HVSON outline supports portable test equipment where PCB area is constrained. Designers should preserve symmetry between CANH and CANL, include accessible test points, and follow the reference circuit for supply filtering and bus protection.
Embedded Diagnostic Interface
The TJA1048TK can form the CAN physical layer of an embedded diagnostic or service interface that needs two links. One path may communicate with a primary controller while another connects to a secondary diagnostic network. Its nominal 5 V operation and compact surface-mount package align with embedded controller boards, and Standby mode can support managed operating states. Confirm the terminal assignments and logic levels in the manufacturer pin table, then apply the specified bus protection and termination strategy.
工程参考数据: TJA1048TK ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | NXP Semiconductors |
| Package | 14-HVSON (3 x 4.5 mm) |
| Terminal Count | 14 terminals |
| Terminal Pitch | 0.65 mm |
| CAN Channel Count | 2 channels |
| Product Type | Dual high-speed CAN transceiver |
| Nominal Supply Voltage | 5 V |
| Operating Mode | Standby mode |
| Packing | Reel-reel, 13-inch reel |
| Minimum Package Quantity | 6000 pieces |
| Minimum Order Quantity | 6000 pieces |
| Stated Lead Time | 10 weeks |
关键差异点
- Two CAN channels in one compact package (对比 Single-channel CAN transceivers)
- Compact automotive-oriented package (对比 Larger-outline 14-pin CAN transceivers)
- Standby operating support (对比 CAN transceivers without a documented standby state)
设计说明
Route CANH and CANL as a closely coupled differential pair with symmetric geometry, continuous ground reference, and minimal stubs. Place the transceiver near the connector or protection network so transient-current paths do not traverse sensitive logic areas. Keep the pair away from switching power inductors and high-current return paths. Confirm the target differential impedance and the complete board stack-up during PCB design, then verify signal and mode performance on the assembled design.
Use the TJA1048 manufacturer application diagram to select and place the supply bypass network near the device. Keep the CAN termination arrangement compatible with the network topology and locate protection components where surge or ESD current can be diverted before reaching the transceiver. The 0.65 mm terminal pitch and compact 3 x 4.5 mm HVSON outline require careful footprint and assembly checks, including the exposed-pad connection and paste pattern shown in the package documentation.
Do not treat TJA1048 ordering suffixes as automatically interchangeable: the TK suffix is associated with the 14-HVSON package, while another suffix may use a different outline. Verify pin functions, exposed-pad requirements, supply limits, and standby logic directly from the relevant datasheet before substitution. Also avoid assuming that a CAN transceiver replaces the CAN protocol controller; the controller and transceiver remain separate functional blocks in the network architecture.
High-speed CAN signaling depends on a physically consistent bus implementation. Match connector and transceiver impedances, provide the correct bus termination, and use a protection network designed for the installation environment. Check radiated and conducted emissions because common-mode currents on CAN wiring can couple into adjacent circuits. The manufacturer's EMC guidance and application circuit should form the basis for the final protection and filtering design.
合规信息
The automotive application is stated by NXP, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for this ordering code.