TLV2332ID - Dual 8V 525kHz Operational Amplifier | Texas Instruments
料号: TLV2332ID ✓ 量产中TLV2332ID 概述
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2332 belongs to the LinCMOS low-voltage, medium-power operational-amplifier family. In the broader component hierarchy, it is an operational amplifier, analog amplifier IC, and semiconductor designed for signal conditioning, buffering, voltage comparison, and feedback control.
The TLV2332 family is specified for operation from a single supply as low as 3 V and is fully characterized at 5 V and 8 V. Its 525 kHz gain-bandwidth product supports moderate-bandwidth signal paths, while the low input-bias-current characteristics provide low input noise current. The common-mode input voltage can extend below the negative rail, which is particularly helpful for sensor interfaces and single-supply amplifier stages whose useful signal range approaches 0 V.
Each device contains two independent amplifier channels. The dual configuration reduces component count and PCB area when a design requires two similar amplifier functions. Because it is a medium-power LinCMOS family member rather than an ultra-low-power comparator or micropower amplifier, it provides a useful balance between bandwidth, low-voltage operation, and drive capability. The exact output-current, input-offset, noise-density, and slew-rate figures should be confirmed in the manufacturer datasheet for the selected operating conditions.
Typical uses include low-voltage sensor conditioning, buffered ADC inputs, portable instrumentation, audio preamplification, threshold detection, and general-purpose analog signal processing. The 3 V and 5 V single-supply characterization makes the device suitable for battery-powered and embedded systems, while its 525 kHz bandwidth supports applications that do not require the speed of a high-frequency precision amplifier.
PCB design should account for input-bias-current-driven offsets, output drive capability, and stable operation near the supply rails. Place input and output compensation or decoupling components close to their associated pins, maintain short feedback paths, and provide adequate ground-return geometry. Check the datasheet pin configuration and common-mode limits before assigning signal sources, particularly when inputs can remain below 0 V relative to the circuit ground.
This product page combines the TLV2332ID device specifications, package details, sourcing guidance, and engineering-oriented design guidance. It also distinguishes documented drop-in choices from unverified substitutions so engineers can assess PCB compatibility, electrical limits, and application fit before approving a replacement.
直接替换替代料: TLV2332ID ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TLV2332ID (相同外形与封装尺寸) ——差异在于 Amplifier Type, Mounting Type.
TLV2332IP
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →TLV2332U
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2332ID 最大额定值与电气特性
| Amplifier Type | Dual operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 8 V |
| Single-Supply Operation | 3 V and 5 V |
| Gain-Bandwidth Product | 525 kHz |
| Common-Mode Input Range | Extends below the negative supply rail |
| Output Voltage Swing | Includes the negative rail |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
TLV2332ID 引脚配置
| 引脚 1 | OUTA — Channel A output |
| 引脚 2 | INTA- — Channel A inverting input |
| 引脚 3 | INTA+ — Channel A non-inverting input |
| 引脚 4 | V- — Negative supply connection |
| 引脚 5 | INTB+ — Channel B non-inverting input |
| 引脚 6 | INTB- — Channel B inverting input |
| 引脚 7 | OUTB — Channel B output |
| 引脚 8 | V+ — Positive supply connection |
典型应用
TLV2332ID 适用于 6 应用s: Battery-Powered Sensor Conditioning, Buffered ADC Input, Portable Audio Preamplification, Low-Voltage Threshold Detection, Portable Test and Measurement, Embedded Control Signal Interface.
Battery-Powered Sensor Conditioning
The TLV2332ID fits battery-powered sensor interfaces because it supports 3 V and 5 V single-supply operation and its common-mode input range extends below the negative rail. A thermistor, resistive sensor, or low-level transducer can therefore be amplified while useful input signals approach ground. The two channels can condition one sensor path and provide a second stage for filtering or level conversion. Its 525 kHz gain-bandwidth product handles slow-to-moderate sensor bandwidth efficiently, while the low input-bias-current characteristics reduce measurement errors with high-impedance sources. Check output swing and supply current against the sensor excitation and battery budget before finalizing the circuit.
推荐
Buffered ADC Input
The TLV2332ID can buffer low-impedance inputs to an analog-to-digital converter when the source has high output impedance or requires gain. Its 525 kHz gain-bandwidth product supports conventional sample-and-hold systems and general-purpose conversion front ends, while two channels can buffer two related sensor channels. The common-mode range extending below the negative rail is useful when a sensor output starts near 0 V on a single supply. The amplifier must still deliver the required output range and settling accuracy at the converter’s acquisition time, so use the electrical-characteristics curves to verify dynamic performance rather than relying on bandwidth alone.
推荐
Portable Audio Preamplification
The TLV2332ID is suitable for low-level audio preamplification in compact, single-supply equipment. Its dual-channel architecture supports left and right signal paths, while the 525 kHz gain-bandwidth product covers voice and other moderate-bandwidth audio content. Operation from 3 V or 5 V accommodates battery-powered and portable-system supply rails, and the common-mode input capability can simplify microphone or line-stage biasing near ground. Actual headroom, output swing, noise, and drive into the next stage should be checked at the intended frequency and load because those performance values depend on operating voltage and circuit configuration.
推荐
Low-Voltage Threshold Detection
The TLV2332ID can implement dual-channel threshold detection by comparing an input with a reference and driving a logic-compatible downstream circuit. Its 525 kHz gain-bandwidth product allows moderately fast comparator-like behavior without operating as a dedicated comparator, and both channels can monitor separate signals. The 3 V and 5 V single-supply ratings make the device useful in embedded control systems. Verify output-current capability, saturation behavior, input offset, and propagation delay at the selected gain and supply voltage; a dedicated comparator may be preferable when rail-to-rail input operation or very fast switching is mandatory.
推荐
Portable Test and Measurement
The TLV2332ID is appropriate for low-level measurement front ends in portable instrumentation because it combines two channels with 3 V and 5 V single-supply operation. The amplifiers can condition two inputs, form differential measurement circuits, or provide buffering between sensors and a converter. A gain-bandwidth product of 525 kHz is sufficient for many general-purpose measurement bandwidths, while operation below 8 V supports compact isolated or battery-powered equipment. The designer should verify input bias current, offset, noise density, output drive, and stability with the intended source impedance and feedback network using the manufacturer’s tested application guidance.
推荐
Embedded Control Signal Interface
The TLV2332ID can interface control, feedback, and actuator signals in embedded equipment operating from 3 V or 5 V. Two independent channels can amplify sensor feedback and condition an analog command simultaneously, reducing package count compared with two separate single amplifiers. The common-mode input range extending below the negative rail is helpful for signals referenced close to ground. Designers should preserve the feedback components near the device, avoid excessive trace resistance in high-impedance inputs, and verify output current and settling behavior against the controlled load to prevent unexpected saturation during transient operation.
推荐
推荐产品汇总
工程参考数据: TLV2332ID ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TLV2332IP | TLV2332U |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Channels | 2 | 2 | 2 |
| Maximum Supply Voltage | 8 V | 8 V | 8 V |
| Gain-Bandwidth Product | 525 kHz | 525 kHz | 525 kHz |
| Single-Supply Operation | 3 V and 5 V | 3 V and 5 V | 3 V and 5 V |
| Common-Mode Input Range | Extends below the negative supply rail | Extends below the negative supply rail | Extends below the negative supply rail |
关键差异点
- Two independent amplifiers in one 8-pin package (对比 TLV2332IP)
- 525 kHz gain-bandwidth product (对比 TLV2332U)
- Single-supply operation with ground-referenced input capability (对比 TLV2332IP)
设计说明
Keep input, feedback, and output paths short and connect decoupling capacitance close to the supply pins. High-impedance sensor inputs can pick up leakage and coupling from adjacent traces, so minimize exposed input-node area and avoid routing beneath noisy switching nodes. Ground the return path directly beneath the amplifier rather than creating a long path through signal traces.
Design for 3 V and 5 V single-supply operation, but observe the 8 V maximum supply rating. Tie the negative supply pin to circuit ground in single-supply systems and connect the positive supply pin through the normal decoupling arrangement. Confirm that signal inputs remain within the common-mode range and that output swing leaves adequate margin for the load; the below-negative-rail input capability does not imply unrestricted output swing.
Do not treat every TLV23xx amplifier as interchangeable. The TLV233x family is optimized for a combination of low power and performance, whereas other family members may differ in speed, power, output swing, or stability. When substituting an amplifier, compare the complete electrical characteristics, feedback configuration, output loading, and pin function rather than relying only on package size or the device family name.
合规信息
The available manufacturer and distributor information does not explicitly state the requested compliance outcomes. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status for the exact orderable MPN before environmental qualification.