TLV2334ID - 4-Channel Low-Power Op Amp | Texas Instruments
料号: TLV2334ID ✗ 停产TLV2334ID 概述
An operational amplifier, commonly called an op amp, is an active semiconductor device that uses high-gain differential amplification to improve the gain, input impedance, and output-drive capability of a feedback circuit. Within the broader hierarchy, the TLV2334ID belongs to the operational amplifier, analog amplifier IC, and signal-conditioning IC categories. Its four channels allow compact designs to process multiple independent analog signals without using separate single-amplifier packages.
Key characteristics include a 300 kHz gain-bandwidth product, approximately 1.1 mV input offset voltage, four amplifier circuits, and operation from a single 3 V or 5 V supply. The 8 V maximum supply supports low-voltage portable equipment, industrial controls, sensor interfaces, and general-purpose analog conditioning. The common-mode range extending below the negative rail is particularly useful when the signal approaches ground.
The TLV2334ID is based on a complementary metal-oxide-semiconductor operational-amplifier design intended for low-voltage operation. Its approximately 300 kHz bandwidth is appropriate for moderate-frequency signal conditioning rather than high-speed video or precision instrumentation. The low-voltage supply capability also simplifies battery-powered designs, although input and output swing limits must be checked against the signal being conditioned.
Typical uses include four-channel sensor interfaces, low-voltage audio and control circuits, instrumentation amplifiers, active filters, comparators with added hysteresis, and general-purpose analog buffers. Because the package contains four amplifiers, channel-to-channel matching is useful when several related low-frequency signals must be processed in one circuit.
When designing a PCB around the TLV2334ID, place input, output, feedback, and decoupling components close to the relevant pins. Use a local supply bypass capacitor on each supply rail and provide a stable, low-impedance ground return. Check input common-mode voltage and output swing before operating near the supply limits; an amplifier can remain powered while its usable input or output range is restricted.
This product page combines the exact catalog attributes and datasheet-search references for the TLV2334ID with practical guidance for supply bypassing, signal conditioning, PCB layout, and drop-in replacement evaluation. It distinguishes confirmed catalog facts from electrical parameters that require review in the manufacturer datasheet before design release.
直接替换替代料: TLV2334ID ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TLV2334ID (相同外形与封装尺寸) ——差异在于 Amplifier Type, Gain-Bandwidth Product, Maximum Supply Voltage, Package.
TLV2374IDR
✅ 直接替换📋 参考替代料(不在目录中)
TLV2374ID
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2372ID
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →TLV2372IDR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2334IP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2334ID 最大额定值与电气特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 4 circuits |
| Number of Amplifiers | 4 amplifiers |
| Maximum Supply Voltage | 8 V |
| Single-Supply Operation | 3 V and 5 V |
| Gain-Bandwidth Product | 300 kHz |
| Input Offset Voltage | 1.1 mV |
| Common-Mode Input Range | Extends below the negative rail and up to VDD |
| 输出电压范围 | Includes negative values |
| 封装 | 14-pin SOIC |
| Package Body Width | 3.90 mm |
| Package Length | 0.154 inch (3.90 mm) width class |
| 安装类型 | Surface mount |
| Process Technology | LinCMOS |
TLV2334ID 0.154 inch (3.90 mm) width class 引脚配置指南
TLV2334ID(0.154 inch (3.90 mm) width class 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TLV2334ID.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TLV2334ID 适用于 6 应用s: Low-Voltage Sensor Signal Conditioning, Industrial Control and Instrumentation, Battery-Powered Portable Equipment, Active Audio and Low-Frequency Filters, Data Acquisition and Analog Front Ends, Power and Motor Control Interfaces.
Low-Voltage Sensor Signal Conditioning
The TLV2334ID fits four-channel sensor-conditioning systems that operate from 3 V or 5 V. Its common-mode input range extends below the negative supply rail, which is valuable when sensor outputs remain near ground. The four amplifiers can buffer or amplify separate inputs without requiring four single-channel packages, while the 300 kHz gain-bandwidth product suits moderate-frequency sensors. Designers should verify the input offset voltage of approximately 1.1 mV against the sensor accuracy requirement and confirm output swing for the selected supply.
推荐
Industrial Control and Instrumentation
The TLV2334ID can implement low-voltage amplification, buffering, and active filtering in industrial control boards. Its 3 V and 5 V single-supply operation supports compact controller subsystems, and the common-mode range extending below the negative rail helps process signals near ground. Four independent channels reduce board area when several control or measurement signals are present. The 300 kHz bandwidth is appropriate for many low-frequency loops, but loop stability, noise, and output-drive requirements should be checked against the specific control topology.
推荐
Battery-Powered Portable Equipment
For battery-powered portable equipment, the TLV2334ID provides four general-purpose amplifier channels from a 3 V or 5 V supply. Its low-voltage operation aligns with energy-conscious designs, and its ability to accept common-mode signals below the negative rail is useful near the bottom of the supply range. The approximately 1.1 mV input offset voltage may dominate accuracy in high-gain sensor paths, so select resistor and gain values accordingly. Confirm output swing and quiescent current in the manufacturer datasheet before finalizing a power budget.
推荐
Active Audio and Low-Frequency Filters
The TLV2334ID can form active filters, channel equalizers, or low-frequency audio-control paths in compact analog boards. Its 300 kHz gain-bandwidth product provides useful bandwidth for moderate-frequency filters, while four channels allow related stereo or multi-axis signal paths to share one package. Common-mode input operation below the negative rail can simplify circuits centered around ground. Check the required filter-Q network, output drive, and output-voltage swing against the 3 V or 5 V supply to avoid clipping near the rail.
推荐
Data Acquisition and Analog Front Ends
The TLV2334ID is suitable for front-end stages in compact data-acquisition systems requiring several low-frequency channels. It can buffer sensor outputs, amplify small signals, and participate in active anti-alias or smoothing filters. The approximately 1.1 mV input offset voltage is important for calibration budgets, while the common-mode range extending below the negative rail helps accommodate near-ground inputs. Verify input capacitance, noise, settling behavior, and output swing in the manufacturer datasheet before sampling at the highest planned rate.
推荐
Power and Motor Control Interfaces
The TLV2334ID can serve as an interface amplifier in low-voltage power-control or motor-control subsystems where several command or feedback signals require conditioning. Its 3 V and 5 V supply operation can align with controller logic rails, and four channels provide flexible signal routing. The common-mode input range below the negative rail is useful for bipolar command signals referenced to ground. The design must remain within the confirmed 8 V maximum supply and must verify output swing, slew rate, capacitive-load behavior, and protection against transient industrial signals.
推荐
推荐产品汇总
工程参考数据: TLV2334ID ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TLV2374IDR | TLV2374ID | TLV2372ID | TLV2372IDR | TLV2334IP |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same |
关键差异点
- Four amplifier channels in one 14-pin SOIC (对比 TLV2374IDR)
- Confirmed low-voltage operating points (对比 TLV2372IDR)
- Near-ground common-mode signal support (对比 TLV2372ID)
设计说明
Route each feedback network directly between its corresponding amplifier output and inverting-input pin. Keep the non-inverting input and feedback components away from switching nodes and high-current return paths. Because the TLV2334ID contains four amplifiers in one 14-pin SOIC, placing the unused channels in a stable configuration, such as a non-inverting unity-gain connection with suitable input biasing, can reduce sensitivity to unused-channel behavior.
Place the supply bypass capacitor close to the package power pin and connect it to a low-impedance ground plane. The confirmed operating points are 3 V and 5 V single supply, with an 8 V maximum supply, but the manufacturer datasheet must be consulted for absolute maximum conditions, quiescent current, and output current. Decouple any sensitive analog supply locally and keep the return current from sensors, filters, and ADC inputs out of the same high-current path.
Do not assume that operation below the negative rail applies to every input condition. The common-mode range extends below the negative rail, but output swing, slew rate, input capacitance, and stability into the selected load remain separate constraints. Use the manufacturer characteristic curves to verify the complete signal path, especially for high-gain configurations, capacitive loads, and signals approaching either supply rail.
合规信息
The available catalog and datasheet-search data do not state a definitive compliance status. Check the current manufacturer product page and material declaration before release.